HBM P3MBP Bedienungsanleitung

A1710-3.3 en

High Pressure

Transducer

Mounting instructions

P3MBP

P3MBP BlueLine

A1710-3.3 en HBM

Contents Page

Safety instructions 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 List of components supplied 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Construction and operating mode 8. . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Mounting 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Electrical connection 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 Cable extension 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Measuring 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Measuring dynamic pressures 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Specifications (in accordance with DIN 16 086) 14. . . . . . . . . . . . . . . .

7 Dimensions (in mm) 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4P3MBP BlueLine

A1710-3.3 enHBM

Safety instructions

Use in accordance with the regulations

The P3MB pressure transducer is to be used exclusively for pressure measu-

rement and directly related control tasks. Any other use is deemed to be not

as prescribed.

To ensure safe operation, the transducer must only be used in accordance

with the specifications in the User Manual. It is also essential to comply with

the statutory and safety regulations relevant to the particular application. This

also applies to the use of accessories.

We declare that the transducer is in conformity with the requirements of the

European Pressure Equipment Directive 97/23/EC, directive of the European

Parliament and Council of 29 May 1997 on the approximation of the laws of

the member states concerning pressure equipment.

The pressure transducer is not a safety device as defined in the regulations

for use. The perfectly safe operation of this pressure transducer requires sui-

table transport as well as technically correct storage, installation and assem-

bly coupled with careful operation.

Use as a ”component with a safety function” does not come under appropriate

use and the user must assess this himself (in the sense of the Pressure

Equipment Directive 97/23/EC).

General dangers in non-observance of the safety instructions

The pressure transducer corresponds to the state of the art and is safe to

operate. The pressure transducer can give rise to residual danger if impro-

perly installed and operated by untrained personnel.

All personnel involved in the installation, commissioning, maintenance or

repair of the pressure transducer must have read and understood the User

Manual and in particular the technical safety instructions.

Accident prevention

Care must be taken to ensure that when the pressure transducer is being

installed or removed, there is no pressure in the circuit.

Residual dangers

The scope of the capabilities and components provided with the transducer

covers only a part of pressure measurement technology. Equipment planners,

installers and operators must plan, carry out and accept responsibility for the

safety engineering aspects of pressure measurement technology in such a

way that residual dangers are kept to a minimum.

P3MBP BlueLine

A1710-3.3 en HBM

All existing regulations must be complied with. There must be reference to the

residual dangers connected with pressure measurement technology.

Even though the P3MB is designed to be as safe as possible, safety regula-

tions demand that burst protection is provided all round the transducer.

The transducer must be protected against mechanical stress or shock.

The resistance of the steel used in the measuring body is only as stated if the

temperatures never rise above or fall below the limits specified in the data

sheet.

If the temperature limits are exceeded – for example, because there is a fire -

the device is rendered unusable.

The end of service life is reached, if the zero signal has changed significantly.

Residual dangers are highlighted in this operating manual with the following

symbols :

Symbol: DANGER

Meaning: Maximum danger level

Warns of an imminently dangerous situation in which failure to comply with

safety requirements will result in death or serious physical injury.

Symbol: WARNING

Meaning: Potentially dangerous situation

Warns of a potentially dangerous situation in which failure to comply with

safety requirements can result in death or serious physical injury.

Symbol: CAUTION

Meaning: Potentially dangerous situation

Warns of a potentially dangerous situation in which failure to comply with

safety requirements could result in damage to property or some form of

physical injury.

6P3MBP BlueLine

A1710-3.3 enHBM

Symbol: NOTE

Means that important information about the product or its handling is being

given.

Symbol:

Meaning: CE mark

The CE mark enables the manufacturer to guarantee that the product com-

plies with the requirements of the relevant EC directives (the declaration of

conformity is available at http://www.hbm.com/support/dokumentation).

Conversions and modifications

The pressure transducer must not be modified from the design or safety-

engineering point of view without our express agreement. Any modification

precludes liability on our part for any damage resulting therefrom.

Qualified personnel

The pressure transducer must only be installed and operated by qualified per-

sonnel strictly in accordance with the technical data relating to the safety

requirements and safety rules and regulations listed. It is also essential to

comply with the statutory and safety regulations relevant to the particular

application. This also applies to the use of accessories.

”Qualified personnel” means persons familiar with the installation, assembly,

commissioning and operation of the product who possess the qualifications

appropriate to their function.

Recalibration and repair

When you send the transducer for calibration or repair to HBM, please specify

the pressure medium used. Traces of the medium can always remain in the

measuring bore. We need this information to act adequately and, if required,

select the appropriate cleaning agent. If no medium has been specified, we

must possibly refuse to perform calibration or repair.

P3MBP BlueLine

A1710-3.3 en HBM

1 List of components supplied

Pressure transducer 1-P3MBP/5000 bar/10000 bar/15000 bar

Double-cone seal with packing (for nominal (rated) measuring range

of 5.000 bar)

Order no.: 2-9289.5512

Double-cone seal (for nominal (rated) measuring range of 10.000 bar and

15.000 bar)

Order no.: 3-9219.0816

User manual

Cable made of polyurethane with Lemosa connector (male) 2-9268.0835

8P3MBP BlueLine

A1710-3.3 enHBM

2 Construction and operating mode

BlueLine series pressure transducers (5000 bar, 10,000 bar, 15,000 bar) have

been designed to measure static and dynamic pressures of fluids.

The development of the P3MB BlueLine was based on HBM’s years of expe-

rience in high pressure technology.

Since 1970, devices in accordance with the P3M principle have been working

successfully with a nominal (rated) measuring range up to 3600 bar.

A large number of devices have proved themselves in dynamic applications.

We are now adding to this type series in the high-pressure direction with the

nominal (rated) measuring range 5000 bar and also adding devices with a

range of 10,000 bar and 15,000 bar

The P3MB BlueLine is suitable for dynamic applications:

•The measuring body is made of field-tested, ductile steel

•P3MB measuring bodies for higher pressures with their threaded connector

are made of a single piece of rolled steel – there is no weld or any other

sort of sealing or jointing point.

•The size of the chosen output signal is big enough to enable measured

value adjustments to be made without too much extra work. On the other

hand, the choice of output signal – or the stresses and strains - should be

small enough for dynamic loading to be possible (without the premature

signs of material fatigue).

•Any fluid or gas (vapour) that does not attack these steels is a suitable

measurement medium. The pressure transducer and its threaded connector

are strengthened for the purpose of the pressure connector and can be

installed anywhere. In particular cases there are specific instructions in

Chapter 3 ”Mounting” which must be followed!

The stated properties are protected by FEM calculations and dynamic loading

tests.

The stated measuring body design, chosen for all devices of the P3MB type

series of measuring ranges 500 bar and above, enables the P3MB to meet a

higher safety standard.

Years of reliable use under dynamic load and in rough operating conditions

provide practical proof that the P3MB has a safe and robust design.

Strain gages (S.G.) are attached directly above the measurement hole. They

are coupled to a Wheatstone bridge and to protect them from harsh ambient

conditions, are located in a hermetically sealed reference chamber. This is

made of stainless steel. In this way, the reliability and precision of the trans-

ducers is assured, even if operating conditions are persistently rough.

P3MBP BlueLine

A1710-3.3 en HBM

3 Mounting

CAUTION

•Before installing the P3MB, check that the threaded connector and the

thread in its counterpart are sound and free of burrs. The parts must fit to-

gether easily.

•Use only the seals provided for this purpose by HBM.

•Devices must never be installed in a counterpart without a relief aperture.

The diameter of the relief aperture should not be less than 2mm. Its purpose

is to safely protect the volume at the root between the two parts, the P3M and

the container or pipework, against an increase in pressure. Even if the seal

leaks, this will prevent destructively high forces ever building up.

P3MB BlueLine transducers are sealed at the pressure connection by a

tapered gasket of 58 °in a beveled run-in to the hole of 60°- as is usual and

successful in ultrahigh pressure technology.

The seal is made from corrosion-resistant material - the 5000 bar version

from 1.4301, the 10.000 bar and 15.000 bar versions from 1.4542.

To minimize the volume in the measurement hole (”dead volume“) packing is

used for these measuring ranges. This forms a unit with the sealing plug. This

makes it very easy to install as well.

The pressure connection thread is M 20 x 1.5.

Pressure transducers can be fitted in any position.

But if the transducer is to be used to measure dynamic pressure characteris-

tics in liquids, it is advisable to install it with the pressure connection upward.

In this way you stop gas accumulating in the measurement hole, where con-

tinually changing compression and release can lead to sizable rises in tem-

perature.

10 P3MBP BlueLine

A1710-3.3 enHBM

CAUTION

When tightening, the wrench (size 27) must only be applied to the

clamping area of the mounting flange, and not to the housing or

cable entry. The permitted tightening torque is 30Nm.

P3MBP 5000

M20 x 1.5

Relief aperture

Double-cone seal

min. 17

P3MBP 10,000 bar

Seal with packing

Ø3.5

Ø6.5

2.7

58o

M20 x 1,5

min. 17

2,3

Ø2,5

Ø6,5

58o

Relief aperture

Double-cone seal

Sealing cone

Fig. 3.1: Installing the pressure transducer

Inhaltsverzeichnis

Beliebte Wandler Handbücher anderer Marken

Camille Bauer

Camille Bauer SINEAX F534 Bedienungsanleitung

Trane

Trane KIT 16724 Montageanleitung

Lumel

Lumel P18 Bedienungsanleitung

B&C Speakers

B&C Speakers DE75PTN Bedienungsanleitung

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Handbuch

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Bedienungsanleitung

ProMinent

ProMinent Dulcometer DMT Bedienungsanleitung

MKS

MKS MicroPirani 925 Series Anleitung zur Verwendung

WIKA

WIKA WU-20 Bedienungsanleitung

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Bedienungsanleitung

Camille Bauer

Camille Bauer SIRAX CH-5610 Bedienungsanleitung

WIKA

WIKA F2802 Bedienungsanleitung

Veris Industries

Veris Industries PW Series Bedienungsanleitung

Simrad

Simrad ES120-7C - REV D Benutzerhandbuch

Airmar

Airmar M260 Bedienungsanleitung

Spirax Sarco

Spirax Sarco ITV1030 Bedienungsanleitung

halstrup-walcher

halstrup-walcher PU10 Bedienungsanleitung

Balluff

Balluff BTL5-P Bedienungsanleitung