HearthStone Stowe 8320 Fehlerbehebungshandbuch

Owner’s Manual & Installation Guide

for the Stowe(8320) GAS-FIRED

DIRECT VENT HEATER

READ THIS OWNER’S

MANUAL

Operate and maintain this gas heater

according to this instruction manual.

Read This Manual In Its Entirety.

WARNING: If the information in these

instructions is not followed exactly, a fire or

explosion may result causing property damage,

personal injury or loss of life.

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch electrical switches; do not use

the phone in your building.

•Immediately call your gas supplier from a

neighbors phone. Follow your gas suppliers

instructions.

•If you cannot reach your gas supplier, call the

fire department.

A qualified installer, service agency or gas supplier

must perform installation and service.

AVERTISSEMENT: Assurez-vous de bien suivre

les instructions donné dans cette notice pour

réduire au minimum le risque d’incendie ou pour

éviter tout dommage matéeriel, toute blessure ou la

mort.

Ne pas entresposer ni utiliser d’essence ni d’autre

vaperurs ou liquides inflammables dans le

voisinage

de cet apprareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE

ODEUR

DE GAZ:

•Ne pas tenter d’allumer d’appareil.

•Ne touchez à aucun interrupteur. Ne pas vous

servir des téléphones se trouvant dans le

batiment où vous vous trouvez.

•Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

•Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le service dos incendies.

L’installation et service doit être exécuté par un

qualifié installer, agence de service ou le

fournisseur de gaz.

Model #8320

6400-40422

05-22-03

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

HearthStone

Quality Home Heating Products

317 Stafford Avenue,

Morrisville, Vermont 05661

E-Mail: [email protected]

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

INFORMATION SHEET

Record, on this page, all relevant information concerning the purchase, installation, and maintenance

of your STOWE Gas-Fired Direct Vent heater. This information will facilitate servicing, purchase of

replacement parts, and warranty claims (if necessary). Keep your original receipt in a safe place as

proof of purchase.

Serial Number:

Fuel type (check one) Natural Gas Liquid Propane

Sold by:

Phone: Date of Purchase:

Installed by:

Phone: Date of Installation:

Gas Supplier:

Phone:

Read this Owner’s Manual before installing or operating the STOWE heater. Retain this manual for future

reference.

SERVICE RECORD

Date Who Performed Work Work Performed Notes:

WHAT WHEN WHAT WHEN

Firebox Cleaning............. annually Door Gasket.................... Replacement as needed

Glass Cleaning................ as needed

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

INTRODUCTION

Congratulations on your purchase of a

Stowe Gas-Fired Direct Vent heater. The

Stowe, by HearthStone, incorporates the

latest in balanced vent gas technology,

which will provide you with clean, efficient

heat for years to come.

The Stowe will provide you with years of

practical and convenient service. However,

as with any gas appliance, the unit must be

properly and safely installed and maintained

by qualified service personnel to ensure safe

and trouble-free operation.

Your Stowe is equipped with a standard

pilot which:

1. generates a milli-volt signal that

powers the wall-mounted thermostat

and;

2. lights the main burner when the

thermostat calls for heat.

This unit is equipped with an

On/Off/T’STAT switch and a variable

output control. The variable output control is

located on the gas control valve. It allows

you to vary the heat output, along with the

flame height to suit personal taste. Heat

output can be reduced {set to “LOW”}

during the Fall and Spring, when the need

for heat is reduced and increased {set to

“HIGH” during Winter months, when the

need for heat is the greatest.

A wall-mounted thermostat is provided by

HearthStone. Regardless of how you set the

variable output control, when the optional

thermostat has been installed and the

On/Off/Thermostat switch is set to

“Thermostat”, the wall-mounted thermostat

will control the on/off cycling of the unit. At

any time, you can override the thermostat

with the On/Off/T’STAT switch by setting it

to “ON” or “OFF”.

The Unit can also be equipped with a speed

blower fan, Kit #93-57001, which turns on

and off independently of the burner flames.

The switch allows you to turn the fan on or

off and control the speed of the fan to suit

your needs. Regardless of the speed the fan

is set, the fan will automatically come on

when the unit heats up.

Also available are two different optional

remote controls. Both of the remote controls

are capable of turning the unit on and off.

One of the optional remotes also allows you

to control the temperature of the stove from

anywhere in the vicinity of the unit. If “ON”

& “OFF” are the only controls required, Kit

# 90-56912 can be used. If you would like to

control the temperature via the remote

control, use Kit # 90-56914.

READ THIS OWNER’S MANUAL

Operate and maintain this gas heater

according to the instructions in this manual.

Read this manual in its entirety. This

manual has two sections, the first section is

for the OPERATOR, and the second section is

for the QUALIFIED SERVICE PERSONNEL only.

HEATER MUST BE INSTALLED

AND MAINTAINED BY QUALIFIED

SERVICE PERSONNEL

Verify the gas connections and venting

systems with requirements of local, regional

or national installation codes. Qualified

service personnel must inspect the gas heater

before use and at least annually.

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

TABLE OF CONTENTS

READ THIS OWNER’S MANUAL........1

INTRODUCTION...........................................4

SAFETY INFORMATION...............................5

FIRE HAZARD........................................... 6

SERVICE CAUTION ................................... 6

HOT SURFACES ........................................ 6

CERAMIC FIBER LOG SAFETY

INFORMATION.......................................... 7

SPECIFICATIONS:.................................7

OWNER’S INFORMATION............................8

ROUTINE MAINTENANCEAND CARE.......10

FIREBOX, PILOT, & BURNER TUBES .......11

INSTALLER’S INFORMATION ....................11

UNPACK AND INSPECT FOR DAMAGE ..... 12

VENTING INFORMATION...........................16

ELECTRICAL CONNECTIONS ....................22

GAS SUPPLY & CONNECTIONS.................25

LOG PLACEMENT .....................................26

LIGHTING THE UNIT FOR THE FIRST TIME

...................................................................28

INITIAL ADJUSTMENTS.............................29

MAINTENANCE AND CARE........................32

PARTS LISTS .............................................34

SAFETY INFORMATION

Your Stowe is a very attractive and extremely

efficient, utilizing today’s best technologies.

By following a few simple safety precautions

and by performing minimal maintenance, the

unit will remain appealing while providing

years of quality performance.

The installation must conform to local codes

or, in the absences of local codes, the current

National Fuel Gas Code, ANSI Z223.1 (NFPA

54) or CAN/CGA B149 Installation Code.

(Installer l’appareil selon les codes ou

réglements locaux, ou, en l’absence de tells

réglements, selon les Codes d’installation

CAN/CGA B149.)

Do not use this appliance if any part has been

under water. Immediately call a qualified

service technician to inspect the heater and to

replace any part of the control system and gas

control that has been under water. (Ne pas se

servir de cet appareil s’il a été plongé dans

l’eau, complétement ou en partie. Appeler un

technicien qualifié pour inspector l’appareil et

remplacer toute partie du systéme de contrôle

et toute commande qui ont été plunges dans

l’lau.)

During the first few hours of operation the

appliance may produce a slight smoke and/or

odor. This is normal during the first several

burns. During the initial burn, open a

window(s) to assist in the removal of the

smoke/odor. If the logs appear to smoke, turn

WARNING:

A qualified s

ervice technician should do

installation and repair. A qualified

service technician should inspect the

appliance before use and at least annually.

More frequent cleaning may be required

due to excessive lint from carpeting,

bedding material, etc. It is

imperative that

control compartments, burners, and

circulating air passages of the appliance

are kept clean and free of obstructions.

(S’assurer que le brûleur et le

compartiment des commandes sont

propres. Voir les instructions

d’installation et d’utilis

ation qui

accompagnent l’appareil.)

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

the heater off and call a qualified service

technician.

The appliance and its individual shutoff valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at test pressures in excess of ½

psig. (3.5k Pa). The appliance must be isolated

from the gas supply piping system by closing

its individual manual shutoff valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less than ½

psig (3.5k Pa).

FIRE HAZARD

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity

of this appliance. The Stowe should be

located out of traffic and away from

furniture, draperies, clothing, and flammable

material.

SHOCK HAZARD

When the optional blower is installed, this

appliance is equipped with a three-prong

(grounding) plug for protection against shock

hazard and should be plugged directly into a

properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from the

plug.

MUST BE VENTED TO THE

OUTSIDE

Never vent the gas heater to other rooms or

buildings. This gas appliance must not be

connected to a chimney flue serving a

separate solid-fuel burning appliance.

SERVICE CAUTION

If you believe your Stowe is not, in any way,

performing properly, immediately

discontinue operation until the unit has been

inspected and approved by qualified service

personnel. Prior to servicing the unit, turn

the valve control knob clockwise to “OFF”.

The unit should be cool prior to servicing

and cleaning. Any safety screen, guard, or

component removed during servicing should

be replaced prior to operation. Use of any

components not supplied by HearthStone on

the stove voids all warranties. Do not

substitute components.

HOT SURFACES

Certain exposed surfaces of the Stowe will

reach high temperatures during normal

operation. Clearances to combustibles must

be maintained, as specified in the “Clearances

To Combustibles” section of this manual.

Due to high temperatures the appliance

should be located out of traffic and away

from furniture, draperies, clothing and

flammable materials. Children and adults

should be alerted to the hazards of high

surface temperatures and should stay away

to avoid burns to skin or clothing ignition.

Young children should be carefully

supervised when in the same room as the

appliance. Clothing or other flammable

material should not be placed on or near

the appliance. (Surveille les enfants. Garder

les vêtements, les meubles, l’essence ou autres

liquides à vapeur inflammables lin de

l’appareil.) Clean the area around, under, and

behind the unit on a regular basis to prevent

the accumulation of dust and lint.

¦WARNING:DO NOT OPERATE THE

APPLIANCE WITH THE FRONT

GLASS REMOVED, CRACKED OR

BROKEN. REPLACEMENT OF GLASS

SHOULD BE DONE BY A LICENSED

OR QUALIFIED SERVICE PERSON.

ONLY OPEN FRONT FOR ROUTINE

SERVICE. DO NOT SLAM OR STRIKE

GLASS.

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

CERAMIC FIBER LOG SAFETY INFORMATION

If the decorative ceramic log material supplied with the Stowe is damaged or missing, it must be

replaced with the same, approved replacement parts supplied by the manufacturer. These

components affect the

combustion quality and safety of the heater. Do not replace fiber ceramic logs with unapproved

ceramic logs or any other material.

Always wear gloves and safety goggles while handling the log set and ember strip.

SPECIFICATIONS:

LISTED: DIRECT VENT GAS HEATER

Listed: DV Gas Heater

Model: Stowe DV Room Heater

Testing Agency: Intertek Testing Services

NA Inc. (ITS)

Tested to: ANSI Z21.88-1998, CSA 2.33-

M98, CAN/CGA2.17

Certified for use by:

Board of State Examiners of Plumbers and Gasfitters

100 Cambridge Street, Room 1511

Boston, Massachusetts

02202

NG LP

Input rating (Btu/hr) 0-2000ft 25,000

25,000

Maximum output (Btu/hr) 0-2000ft 24,400

24,000

Minimum input rating (Btu/hr) 14,500

14,300

Orifice size DMS 0-2000ft 40 53

Man. pressure-HI setting (in.w.c./kPa) 3.5/0.87

10.0/2.48

Man. pressure-LO setting (in.w.c./kPa) 1.2/0.30

3.3/0.80

Inlet pressure-HI (in.w.c./kPa.) 7.0/1.74

13.0/2.75

Inlet pressure-Lo (in.w.c./kPa) 5.0/1.24

11.0/2.88

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

OWNER’S INFORMATION

The installation must conform with local

codes or, in the absences of local codes, the

current National Fuel Gas Code, ANSI Z223.1

(NFPA 54) or CAN/CGA B149 Installation

Code. (Installer l’appareil selon les codes ou

règlements locaux, ou, en l’absence de tels

règlements, selon les Codes d’installation

CAN/CGA-B149.)Do not use this appliance

if any part has been under water.

Immediately call a qualified service

technician to inspect the heater and to

replace any part of the control system and

gas control that has been under water. (Ne

pas se servir de cet appareil s’il a été plongé

dans l’eau, complètement ou en partie.

Appeler un technicien qualifié pour inspector

l’appareil et remplacer toute partie du système

de contrôle et toute commande qui ont été

plongés dans l’lau.

LIGHTING INSTRUCTIONS

NOTE: The gas control knobs and the piezo

ignitor are located behind the control valve

access door, under the front of the unit.

1. STOP! Read the What To Do If You

Smell Gas! Warning (on the cover of

this manual).

2. Set the on/off/T’STAT switch or

thermostat

to the “OFF” position.

3. Push in and turn gas control knob

clockwise to “OFF”. (If not previously

lit, the knob should be in this position.)

4. Wait (5) five minutes to clear out any

gas. If you then smell gas, STOP! Smell

all around the appliance area for gas.

Be sure to smell next to the floor

because some gases are heavier than air

and will settle on the floor. If you smell

gas immediately follow the What To Do

If You Smell Gas! warning on the cover

of this Manual. If you do not smell gas,

proceed to the next step.

5. Set the ON/OFF/T’STAT switch to

“ON” or, if the thermostat has been

installed, “T’STAT”.

6. Turn gas control knob counter-clockwise

to “PILOT”.

7. Push in control knob all the way and

hold in. Immediately light the pilot with

the gas lighter (push in and “click” the

piezoelectric spark ignitor button several

times until lit). Continue to hold the

control knob in for about 20 seconds

after the pilot is lit. Release the knob and

it will pop back out. Pilot should remain

lit. If the pilot goes out, repeat the

operation.

* If knob does not pop out when released,

stop, shut off the gas supply to the heater

and immediately call a qualified service

technician or gas supplier.

* If the pilot will not stay lit after several

tries, turn the gas control knob “OFF” and

call a qualified service technician or gas

supplier.

8. After the pilot lights, turn gas control

knob counter-clockwise to “ON”.

9. Shut the gas control valve access door.

10. If the ON/OFF/T’STAT switch is set to

“ON”, the stove should now be lit. If the

thermostat (or remote) has been

installed, set the ON/OFF T’STAT

switch to “T’STAT” and turn the

thermostat (or remote) to “ON”. Then

set the desired temperature.

NOTE: When pressing/clicking the

piezoelectric spark ignition button to light

the pilot, watch through the glass (front) of

the unit. Click the ignitor button until a

flame is visible at the pilot. Once the pilot is

lit, continue to press on the gas control knob

for another 20 seconds, then release.

Ascertain that the pilot is still lit by looking

through the front door. If lit, then turn the

gas control knob fully counter-clockwise to

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

the “ON” position. If the pilot fails to light,

or if it went out due to a premature release

of the gas control knob while pressed in the

“PILOT” position, wait 60 seconds for the

Interlock to release. Then repeat the lighting

process as described in this section of the

manual.

Once the pilot has been lit, the gas control

knob has been turned to the “ON” position,

and the ON/OFF/T’STAT switch has been

turned to “ON”, the main burners should

light immediately. If you would like to use

the thermostat and it has been installed,

switch the ON/OFF/T’STAT switch to

thermostat. Turn the thermostat to "ON" and

set it to a higher position so that it "calls" for

heat in order to turn light the main burners

(i.e. turns the unit on). Note that the

thermostat controls the on/off cycling of the

main burners, but the pilot remains lit

regardless of the thermostat setting. The

only way to turn the pilot off is to turn the

gas control knob fully clockwise to the

“OFF” position.

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to the “OFF”

position or turn the ON/OFF/T’

STAT switch to the “OFF” position.

2. If shutting the unit off for the non-

heating season, turn the gas control

knob fully clockwise to the “OFF”

position. Do not force the knob to

turn.

DAILY OPERATION

The Stowe gas-fired heater is easily operated

by the homeowner once installed and

adjusted by a qualified service technician.

Following is a list of the controls available

to the owner/user:

A. ON/OFF/PILOT………Built into Valve

B. VARIABLE OUTPUT

CONTROL……………Built into Valve

C. ON/OFF/T’STAT

SWITCH…………………...…Standard

D. THERMOSTAT………………Standard

E. REMOTE CONTROL (w/o

thermostat)…………………....Optional

F. REMOTE CONTROL

(w/thermostat)…………….…..Optional

G. BLOWER……………………..Optional

A. ON/OFF/PILOT

The valve is equipped with two “control

knobs”. One is the ON/OFF/PILOT

knob, located on the front left side of the

valve. When in the “OFF” position, the

unit cannot operate at all. When in the

“PILOT” position, the pilot light can be

lit, but that is all. When in the “ON”

position, the unit may be on

continuously, or it may be “waiting” to

be controlled by the thermostat or

remote, depending on the setting of the

other controls.

B. VARIABLE OUTPUT CONTROL

The Variable Output Control knob,

located on the front right side of the

valve, controls the “rate” heat is

produced. By adjusting the variable

output control the rate of heat output can

be varied to meet the heating

requirements of the season. Choosing a

“LOW” flame setting will result in

longer burn cycles at a reduced output,

while choosing a “HIGH” flame setting

will result in a shorter, hotter burn cycle.

Through trial and error you can select

the optimum flame size for you setting

and application.

C. ON/OFF/T’STAT SWITCH

The ON/OFF/T’STAT switch controls

how the unit will operate, continuously

or by thermostat. When the switch is in

the “ON” position, the main burner

HearthStone Quality Home Heating Products Inc STOWE Gas-Fired Direct Vent heater

will stay on constantly, and the

thermostat will not operate. When the

switch is in the “T’STAT” position, it

will operate via the thermostat, running

only when the thermostat “calls” for

heat. When the switch is in the “OFF”

position, the pilot remains lit but the unit

can not operate, as the main burner can

not light.

D. THERMOSTAT

The unit may be controlled

automatically via the wall-mounted

thermostat. By setting the

ON/OFF/T’STAT switch to “T’STAT”,

and setting the desired room

temperature, the unit will cycle on and

off as needed to maintain the requested

temperature.

E. REMOTE CONTROL (w/o thermostat)

The unit may also be partially controlled

via the OPTIONAL remote control, Kit

#90-56912. When the ON/OFF/T’STAT

switch is in the “T’STAT” position, it

allows you to turn the stove “On” &

“Off” from anywhere in the vicinity of

the unit, and is available through your

local HearthStone dealer.

F. REMOTE CONTROL (w/thermostat)

The unit may also be fully controlled via

the OPTIONAL REMOTE CONTROL

w/thermostat, available through your

local HearthStone dealer Kit #90-56914.

When the ON/OFF/T’STAT switch is in

the “T’STAT” position, this Remote

allows you to turn the unit “On” & “Off”

and also allows you to control the

temperature of the stove from anywhere

in the vicinity of the unit.

G. BLOWER

The unit may be equipped with an

OPTIONAL variable blower fan,

available through your local HearthStone

dealer Kit #93-57001. The fan helps to

circulate heat away from the stove.

Note: The ON/OFF/T’STAT switch or the

T’STAT controls the on/off cycling of the

main burners, but the pilot remains lit

regardless of any of the control settings (B-

G) listed previously, except the

ON/OFF/PILOT control knob, which is the

only way to turn the pilot off. Turning the

gas control knob fully clockwise to the

"OFF" position will turn off the pilot.

During the summer, non-heating season,

switch the wall thermostat and rocker

switches to “OFF”, and turn off the pilot.

This will improve the overall efficiency of

the unit, as the heat from the pilot is not

wanted in the summer. When putting the

unit back into service follow the “Lighting

of the Unit” portion in the “How To Turn

On & Off” section of this manual.

When the unit is first lit, especially when

cool, it is normal to experience some

condensation on the inside of the glass

window. This condensation will burn off

within the first few minutes of operation. If

continuous condensation or water drips are

noted from any part of the unit, immediately

discontinue operation of the unit and contact

a qualified service technician.

ROUTINE MAINTENANCE

AND CARE

The Stowe requires minimal routine

maintenance and care. The unit should

always be cool and off when being cleaned.

Inhaltsverzeichnis

Andere HearthStone Gasheizung Handbücher

HearthStone

HearthStone STERLING "G" 8531 Bedienungsanleitung

HearthStone

HearthStone 8160 Bedienungsanleitung

HearthStone

HearthStone Tudor Fehlerbehebungshandbuch

HearthStone

HearthStone Tudor 8120 Programmierhandbuch

HearthStone

HearthStone Bristol DX Bedienungsanleitung

HearthStone

HearthStone Stowe DX 8322 Bedienungsanleitung

HearthStone

HearthStone STERLING "G" B-VENT 8521 Bedienungsanleitung

HearthStone

HearthStone Killington Bedienungsanleitung

HearthStone

HearthStone Aurora 8900 Series Bedienungsanleitung

HearthStone

HearthStone Santa Fe Fehlerbehebungshandbuch

HearthStone

HearthStone Santa Fe 8761 Bedienungsanleitung

HearthStone

HearthStone Champlain Bedienungsanleitung

HearthStone

HearthStone Tribute DV 8050 Programmierhandbuch

HearthStone

HearthStone AURORA Eclipse DV 8901 Series Bedienungsanleitung

HearthStone

HearthStone Waitsfield DX 8770 Bedienungsanleitung

HearthStone

HearthStone Tribute DV 8050 Fehlerbehebungshandbuch

HearthStone

HearthStone Tucson (8700) Fehlerbehebungshandbuch

HearthStone

HearthStone TUCSON Bedienungsanleitung

HearthStone

HearthStone Champlain 8302 Bedienungsanleitung

HearthStone

HearthStone hase-Bari 8180 Bedienungsanleitung

HearthStone

HearthStone Champlain 8303 Bedienungsanleitung

HearthStone

HearthStone Santa Fe Fehlerbehebungshandbuch

HearthStone

HearthStone Stowe Bedienungsanleitung

HearthStone

HearthStone TUCSON 8745 Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung