HearthStone TUCSON Bedienungsanleitung

OWNER’S MANUAL

TUCSON

Gas-Fired Catalytic Vent-Free Room Heater

(8740)

Manufacturedby:

HearthStoneQuality Home Heating Products, Inc.

317 Stafford Avenue

Morrisville, Vermont 05661

READ THIS OWNER’S MANUAL

Operate and maintain this gas heater according to

instructions in this manual.

Read this manual in its entirety.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result, causing

property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to page 6 of this

manual.

FOR YOUR SAFETY - WHAT TO DO IF YOU SMELL GAS

* DO NOT ATTEMPT TO LIGHT THIS GAS HEATER OR ANY APPLIANCE

* EXTINGUISH ANY OPEN FLAME

* DO NOT TOUCH ANY ELECTRICAL SWITCH

* DO NOT PLUG IN OR UNPLUG ANY APPLIANCE

* DO NOT USE ANY PHONE IN YOUR BUILDING

* OPEN WINDOWS IN THE ROOM AND VACATE THE BUILDING

* TURN OFF THE MAIN GAS SUPPLY

* IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE

* FOLLOW THE GAS SUPPLIERS INSTRUCTIONS

* IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT

6400-40434 12/01

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-1-

INFORMATION SHEET

Record, on this page, all relevant information concerning the purchase, installation, and maintenance of

your Tucson gas-fired heater. This information will facilitate servicing, purchase of replacement parts, and

warranty claims (if necessary). Keep your original receipt in a safe place as proof of purchase.

Serial Number:

Fuel type (check one) Natural Gas

Liquid Propane

Sold by:

Phone: Date of Purchase:

Installed by:

Phone: Date of Installation:

Gas Supplier:

Phone:

Read this Owner’s Manual before installing or operating the Tucson gas-fired heater. Retain this manual for

future reference.

SERVICE RECORD

Date Who Performed Work Work Performed Notes

WHAT WHEN WHAT WHEN

Firebox Cleaning............. annually Door Gasket.................... replacement as needed

Catalytic combustor......... visual check annually Glass Cleaning................ as needed

Catalytic combustor......... replacement every 5 yrs. or as needed (do not clean the catalytic combustor)

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-2-

INTRODUCTION

Welcome

Congratulations on the purchase of your HearthStone

Tucson Gas-Fired Catalytic Vent-Free Stove. The

Tucson incorporates the latest in energy and gas

technology which will provide you with clean, efficient

heat for years to come. The combination of natural stone

and cast iron gives the Tucson years of attractive looks

and allows for durable performance which can be

maintained with minimal care.

If there are any questions regarding installation or

operation, which are not answered within this manual,

contact your local dealer or your building inspector.

Your Tucson is equipped with a standing pilot which:

1) generates a millivolt signal that powers the

wall-mounted thermostat and;

2) lights the main burner when the thermostat

calls for heat. (The Tucson requires no

electrical power source for normal operation).

This unit is equipped with a variable output control

located on the gas control valve. It allows you to vary

the heat output, along with the flame height, to suit

personal needs. Heat output can be reduced during the

Fall and Spring (when the need for heat is reduced) and

increased during Winter months (when the need for heat

is the greatest). Regardless of how you set the variable

output control, the on/off cycling of the unit may be

controlled by the wall-mounted thermostat, or the

on/off/Tstat switch.

The Tucson will provide you with years of practical and

convenient service. However, as with any gas appliance,

the unit must be properly installed and maintained by

qualified service personnel to ensure safe and trouble-

free operation.

Table of Contents

Information Sheet...........................................1

Service Record...............................................1

Introduction....................................................2

Safety Information..........................................3

Clearances To Combustibles..........................5

Hearth Requirements/Floor Protection...........5

FreshAirRequirements.....................5

DeterminingSpace Classifications..................6

Meeting FreshAir Requirements....................9

PackingList&Items Required For

Installation......................................................9

Unpack &Inspect For Damage.......................9

Electrical Connections...................................10

Gas Supply &Connections............................11

LogSet Information.......................................12

Before The Stove Is Lit................................13

How To Turn The Unit On & Off................14

Burner Flame Appearance............................15

Initial Adjustments.......................................16

Daily Operation............................................16

Routine Maintenance and Care.....................17

Parts List.........................................19

Specifications...............................................19

Trouble Shooting.........................................20

Warranty......................................................22

READ THIS OWNER’S MANUAL

Operate and maintain this gas heater according to

instructions in this manual. Read this manual in its

entirety.

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-3-

SAFETY INFORMATION

Your Tucson Vent-Free is very attractive and extremely efficient,

utilizing today’s best technologies. By following a few simple

safety precautions and by performing minimal maintenance, the

unit will remain appealing while providing years of quality

performance.

WARNING

Installation and repair should be done by a qualified service

person. The appliance should be inspected before use and at

least annually by a qualified service person. It is imperative

that control compartments, burners, and circulating air

passages of the appliance are kept clean and free of

obstructions.

IMPORTANT

Please read and understand all warnings before installing or

operating this heater. Failure to follow these instructions or

improper use of this heater will void the warranty and can

cause serious injury or death from burns, fire, explosion and

carbon monoxide poisoning. Do not attempt to alter or modify

the construction of this heater or its components. Any

alteration or modification of construction voids the warranty

and the certification of this heater. Save this manual for future

reference.

DANGER: CARBON MONOXIDE

POISONING MAY LEAD TO DEATH!

Carbon Monoxide Poisoning: Early signs of carbon monoxide

poisoning resemble the flu with headaches, dizziness, and/or

nausea. If you have these signs, get fresh air immediately! Have

the heater serviced, as it may not be operating properly. As a safety

precaution, a CO monitor may be installed in or near the room

where the unit will be operating.

The installation must conform with local codes or, in the absences

of local codes, the current National Fuel Gas Code, ANSI Z223.1

(NFPA 54).

DO NOT INSTALL THIS HEATER IN A BEDROOM OR

BATHROOM.

Do not use this heater if any part has been under water.

Immediately call a qualified service technician to inspect the heater

and to replace any part of the control system and gas control which

has been under water.

This heater has a standing pilot which incorporates an Oxygen

Depletion System (ODS). The ODS shuts off the flow of gas to the

pilot and the burner in the event that sufficient fresh air becomes

unavailable for continued safe operation of the heater. If this heater

shuts off during operation, sufficient fresh air may not be available.

Refer to the Troubleshooting or Fresh Air Requirements sections

of this manual, or call a qualified service technician.

Avoid any drafts that alter the burner flame patterns. Do not

allow fans to blow directly into the heater. Ceiling fans may

create drafts that alter burner flame patterns. Sooting and

improper burning may occur.

This unvented gas heater is intended to be smokeless. During the

first few hours of operation the appliance may produce a slight

smoke and/or odor. This is normal during the first burn. During

the initial burn, open a window(s) to assist in the removal of the

smoke/odor. If the logs appear to smoke, turn the heater off and

call a qualified service technician.

During any pressure testing of supply piping system in excess of

½ psi (14" w.c.), the heater and its control valve must be

disconnected from the gas supply system.

If equal to or less

than ½ psig, it must be isolated from the gas supply piping

system by closing its individual manual shutoff valve.

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-4-

SAFETY INFORMATION cont.

WARNING:

DO NOT OPERATE THIS HEATER

WITHOUT THE CATALYTIC COMBUSTOR PROPERLY

INSTALLED. IF THE CATALYST APPEARS ALTERED

OR DAMAGED, DO NOT USE THE APPLIANCE UNTIL

THE CATALYST IS REPLACED.

HOT SURFACES

Certain exposed surfaces of the Tucson will reach high

temperatures during normal operation. Clearances to

combustibles must be maintained, as specified in the Clearances

To Combustibles section of this manual. The Tucson should be

located out of traffic and away from furniture, draperies, clothing

and flammable materials. Do not place objects that may obstruct

air circulation on, under, or near the heater. Do not place objects

on the top grill of the stove. Doing so will obstruct the air flow

of the stove, preventing it from operating properly. Clean the

area around, under, and behind the unit on a regular basis to

prevent the accumulation of dust and lint.

Children and adults who are unfamiliar with heaters of this type

should be alerted to the hazards of high surface temperatures and

warned that they should stay away to avoid burns to skin and

clothing. Children should be carefully supervised when in the

same area as the Tucson heater. Do not leave children unattended

in the vicinity of this unit.

NEVER BURN PAPER, WOOD, OR OTHER

MATERIALS

This gas heater is designed to burn either natural gas(NG) or

liquid propane(LP). Never burn any fuel which was not intended

for use.

DO NOT LIGHT PILOT OR MAIN BURNERS BY

HAND

The standing pilot light equipped with this gas heater is lit by

using a piezoelectric spark generator, as described in the How To

Turn the Unit On & Off section of this manual. Never attempt to

light the pilot or main burners by hand (with a match or lighter).

After repeated attempts, if the pilot light fails to light,

discontinue operation, turn off the gas at the gas control valve,

and immediately contact qualified service personnel for

assistance.

FIRE HAZARD

Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this appliance. The Tucson should be

located out of traffic and away from furniture, draperies,

clothing, and flammable material.

CERAMIC FIBER LOG SAFETY INFORMATION

If the decorative ceramic logs and ember strip material

supplied with the Tucson are damaged or missing, they

must be replaced with the same, approved replacement

parts supplied by the manufacturer. These components

affect the combustion quality and safety of the heater. Do

not replace fiber ceramic logs or ember strip with

unapproved ceramic logs or any other material. Always

wear gloves and safety goggles while handling the log

set and ember strip.

SERVICE CAUTION

If you believe your Tucson is not, in any way, performing

properly, immediately discontinue operation until the unit

has been inspected and approved by qualified service

personnel. Prior to servicing the unit, turn the valve control

knob clockwise to “OFF”. The unit should be cool prior to

servicing and cleaning. Any component removed during

servicing should be replaced prior to operation. Use of any

components not supplied by HearthStone. on the stove

voids all warranties. Do not substitute components.

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-5-

CLEARANCES TO COMBUSTIBLES

Due to high surface temperatures,

the Tucson should be located out of

traffic and away from furniture and

draperies. Clothing and other

flammable material should not be

placed on or near the Tucson heater.

Always maintain adequate

clearances around the air openings

into the combustion chamber and

allow for adequate ventilation.

Minimum clearances to

combustibles must be maintained as

shown to the right, in Figures 1-4.

HEARTH

REQUIREMENTS/FLOO

R PROTECTION

The Tucson can be installed on wood

flooring or a non-combustible surface.

For installation of the Tucson on

carpeting, vinyl tile, or other combustible materials

other than wood flooring, the unit shall be installed on

a metal, wood, or other non-combustible hearth.

The required size of the hearth is thesame

as the outline of the stove (shown in Figure 19).

NOTE: Some wood floor varnishes, stains, or

polyurethane may be affected by heat.

CODES

Adhere to all local codes or, in their absence, the latest edition of THE NATIONAL FUEL GAS CODE ANSI Z223.1

(NFPA54) which can be obtained from:

AMERICAN NATIONAL STANDARDS INSTITUTE, INC.

1430 BROADWAY

NEW YORK, NY 10018

NATIONAL FIRE PROTECTION ASSOCIATION, INC.

BATTERY MARCH PARK

QUINCY, MA 02269

FRESH AIR REQUIREMENTS

Your Tucson stove requires an adequate supply of fresh air

to function properly and safely. The fresh air supply must be

met within the space in which the heater is to be installed. To

ensure an adequate supply of fresh air is available for proper

and safe operation of your Tucson stove, the following

information must be considered when installing the appliance

in a mobile home, modular home, or an on-site house, Refer

to Figure 5.

The space in which the heater should be installed will fall

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-6-

into one of the following categories: 1. Unusually tight construction

2. Unconfined space

3. Confined space

WARNING:

If the area in which the heater may be

operated is smaller than that defined as an unconfined

space, provide adequate combustion and ventilation air

by one of the methods described in the National Fuel Gas

Code ANSI Z223.1, Latest Edition, Section 5.3.

DETERMINING SPACE CLASSIFICATION

Unusually tight construction

This is construction where:

a. Walls and ceilings exposed to the outside atmosphere have

a continuous water vapor retarder with a rating of one perm

(6 x 10

¹¹ kg per pa-sec-m²) or less with openings gasketed

or sealed, and

b. Weatherstripping has been added on openable windows

and doors, and

c. Caulking or sealants are applied to areas such as joints

around window and door frames, between sole plates and

floors, between wall ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines, and at

other openings.

If the space in which the heater will be installed falls into this

category, supplemental fresh air must be provided, as

outlined in the Meeting Fresh Air Requirements section of

this manual.

Unconfined space

If the space in which the heater is to be installed meets the

following criteria, it is considered to be an unconfined space.

The room in which the heater is to be installed has an air

volume of at least 50 cubic feet (cubic feet = length x width

x height of the space) for each 1000 BTU/hr (4.8 m³ / K. W.)

input rating for all appliances in the space. This includes

adjoining rooms only if there are doorless passageways

between them, or there are vents between the rooms. If the

space in which the unit is being installed is an unconfined

space, additional fresh air is not needed.

Confined space

If the space in which the heater is to be installed meets the

following criteria, it is considered a confined space.

The room in which the heater is to be installed has an air

volume of less than 50 cubic feet for each 1000 BTU/hr (4.8

m³ / K. W.) input rating for all appliances in the space. This

includes adjoining rooms only if there are doorless

passageways between them, or there are vents between the

rooms.(See Figure 5).

If the space in which the heater is to be installed is a confined

space, additional fresh air must be provided. This can be

done by one of the ways outlined in the Meeting Fresh Air

Requirements section of this manual.

Example (refer to Figure 5)

I. Determine the volume of the space where the unit will be

installed. Volume = length x width x height. Also included

in the volume of the space is the volume of any adjoining

rooms, only if there are doorless passage ways between them,

or if there are vents between the rooms.

II. Multiply the volume by 1000 BTU/hr, then divide that

number by 50 cubic feet, to obtain the

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-7-

The following formula can be used to determine the maximum heater rating per the

definition of unconfined space:

(L1 + L2) FT x (W) FT x (H) FT x 1000

BTU/HR =

EXAMPLE:

Consider two connecting rooms with an open area between, with the following dimensions:

L1 = 15 1/2 Ft., L2 = 12 Ft., W = 12Ft., H = 8 Ft.

(15 1/2 + 12) x (12) x (8) x 1000

BTU/HR =

BTU/HR = 52,800

If there were a door between the two rooms the calculation would be based only on the

room with the heater.

(15 1/2) x (12) x (8) x 1000

BTU/HR =

BTU/HR = 29,760

DETERMINING SPACE CLASSIFICATION cont.

total maximum BTU/hr rating which the room can support.

III. Add the BTU/hr ratings of all fuel burning appliances

installed within the same space. The BTU rating for this unit

is 20,000 BTU/hr. (Do not include any direct vent

appliances, as these types of appliances use outside air for

combustion and venting).

IV. Compare the maximum BTU/hr rating that the room can

support (from II.) with the maximum BTU/hr rating of the

combined appliances (from III.). If the number from III. is

smaller than the number calculated in II., the space should be

considered an unconfined space. If the number from III. is

larger than II., the space should be considered a confined

space, and additional fresh air must be provided. This can be

done by one of several ways.

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-8-

INLET AIR

OPENINGS

VENTILATION LOUVERS

(EACH END OF ATTIC)

VENTILATION LOUVERS FOR

UNHEATED CRAWL SPACE

FIGURE 6

FIGURE 7

FIGURE 8

(EACH END OF ATTIC)

VENTILATION LOUVERS

OUTLET

AIR

INLET AIR DUCT

(ENDS 1 FT ABOVE FLOOR)

FIGURE 9

OUTLET AIR

DUCT

INLET AIR

DUCT

OUTLET

AIR

MEETING FRESH AIR REQUIREMENTS

1. Air from inside the building.The confined space shall be

provided with two permanent openings communicating directly

with an additional room(s), of sufficient volume, so that the

combined volume of all spaces meets the criteria for an

unconfined space. The total input of all gas utilization equipment

installed in the combined space shall be considered in making this

determination. Each opening shall have a minimum free area of 1

square inch per 1,000 BTU/hr (22 cm² / kW) of the total input

rating of all gas utilization equipment in the confined space, but

not less than 100 square inches (645 cm²). One opening shall

commence within 12 inches (30 cm) of the top, and one opening

shall commence within 12 inches (30 cm) of the bottom, of the

enclosure. The minimum dimension of air openings shall not be

less than 9 square inches (8 cm) (see Figure 6).

2. All air from outdoors. The confined space needs to have two

permanent openings, one commencing within 12 inches (30 cm)

of the top, and one commencing within 12 inches (30 cm) of the

bottom, of the enclosure. The openings shall communicate freely

with the outdoors, either directly, by ducts, or by spaces (crawl or

attic). The minimum dimension of air openings shall be not less

than 9 square inches (8 cm). See Figures 7 thru 9.

A. Where directly communicating with the outdoors, each

opening shall have a minimum free area of 1 square inch per

4,000 BTU/hr (5.5 cm² / kW) of total input rating of all equipment

in the enclosure. See Figure 7.

B. Where communicating with the outdoors through vertical

ducts, each opening shall have a minimum free area of 1 square

inch per 4,000 BTU/hr (5.5 cm² / kW) of total input rating of all

equipment in the enclosure (See Figure 8).

C. Where communicating with the outdoors through horizontal

ducts, each opening shall have a minimum free area of 1 square

inch per 2,000 BTU/hr (11 cm² / kW) of total input rating of all

equipment in the enclosure (See Figure 9).

D. Where ducts are used, they shall be of the same cross-

sectional area as the free area of the openings to which they

connect.

OWNER’S MANUAL MODEL: 8740 TUCSON Vent-Free ROOM HEATER

-9-

PACKING LIST & ITEMS REQUIRED FOR INSTALLATION

Packing list

1 - Tucson Vent-Free

Gas-Fired Heater

1 - Decorative Ceramic Fiber Log

1 - Ember Strip

1 - Thermostat with 40' wire

1 - Owners Manual

1 - Warranty Validation Form

Items Required For Installation

Ensure that the following items are available before proceeding with

installation:

1/8 Allen wrench

An external regulator (for propane/ L. P. gas only)

Gas piping which complies with local codes

Pipe sealants approved for use with propane/L. P. Gas (resistant to

sulfur compounds)

A manual shutoff valve for the gas supply

A sediment trap

Pipe wrenches

Phillips head screwdriver

Other parts required by local code

Safety glasses

Gloves

UNPACK & INSPECT FOR DAMAGE

Unpack

The Tucson is packaged by the manufacturer to

withstand shipment without damage under most

circumstances. However, damage can occur during

transit and handling. Care should be taken when

unpacking, inspecting for damage, and installing the

unit. If any damaged or missing parts are detected,

immediately contact your dealer.

After removing the shipping carton, carefully remove the

top three stones and grill. Use the protective wrapping

material to temporarily protect the stones from chipping

or damage while the unit is inspected and installed.

With the top stones and grill removed and set aside, undo

the lag bolts that fasten the unit to the pallet. Take care

not to mar or chip the legs if enameled. Lift the stove off

the pallet and set it in place, (with regards to the

Clearances To Combustibles section of this manual.)

Inspect for damage

Inspect the Tucson for visible and/or concealed damage.

The unit should appear to be square and true. The stones

should be whole and without cracks, chips, or breakage.

The sheet metal parts should be smooth and free of

bends and/or dents.

If the heater is enameled, the enameled cast iron should

be free of chips and/or cracks. If visible or concealed

damage is found or suspected, contact your local dealer

for instructions.

The Owner’s Manual, thermostat (with wire), removable

ash lip, and the decorative ceramic fiber logs, supplied with

the Tucson, are contained within the firebox. It is

important to wear the safety goggles and gloves when

handling the log set. Open the firebox door using a 1/8

allen wrench and inspect the logs for damage. If a damaged

log is encountered, contact your local dealer for

replacement logs. Put the logset, thermostat, and the ash lip

aside. They will be installed later.

Andere Handbücher für TUCSON

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HearthStone Gasheizung Handbücher

HearthStone

HearthStone Waitsfield DX 8770 Bedienungsanleitung

HearthStone

HearthStone Champlain 8303 Bedienungsanleitung

HearthStone

HearthStone 8050 Fehlerbehebungshandbuch

HearthStone

HearthStone Stowe Bedienungsanleitung

HearthStone

HearthStone TUCSON 8745 Bedienungsanleitung

HearthStone

HearthStone Tucson (8700) Fehlerbehebungshandbuch

HearthStone

HearthStone AURORA Eclipse DV 8901 Series Bedienungsanleitung

HearthStone

HearthStone Stowe 8320 Fehlerbehebungshandbuch

HearthStone

HearthStone Killington Bedienungsanleitung

HearthStone

HearthStone Bristol DX Bedienungsanleitung

HearthStone

HearthStone AURORA SL-26N Bedienungsanleitung

HearthStone

HearthStone Santa Fe Fehlerbehebungshandbuch

HearthStone

HearthStone Tudor 8120 Programmierhandbuch

HearthStone

HearthStone STERLING "G" B-VENT 8521 Bedienungsanleitung

HearthStone

HearthStone Champlain 8302 Bedienungsanleitung

HearthStone

HearthStone hase-Bari 8180 Bedienungsanleitung

HearthStone

HearthStone Stowe 8324 Bedienungsanleitung

HearthStone

HearthStone Tribute DV 8050 Fehlerbehebungshandbuch

HearthStone

HearthStone Tudor Fehlerbehebungshandbuch

HearthStone

HearthStone Tribute DV 8050 Programmierhandbuch

HearthStone

HearthStone Champlain 8301 Bedienungsanleitung

HearthStone

HearthStone Santa Fe 8761 Bedienungsanleitung

HearthStone

HearthStone STERLING "G" 8531 Bedienungsanleitung

HearthStone

HearthStone FS-16N-TV Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung