Heat & Glo I30-X Bedienungsanleitung

i30-X Freestanding

Assembly Instructions

Further information can be found at:

https://jetmastervic.com.au/brochures-specifications/

These instructions are to be used in conjunction with the general i30-X installation manual that is

shipped with the unit.

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION

DO NOT MODIFY THIS APPLIANCE

Page 1

i30-X Freestanding case

Components

Ref Description QTY

1 Base 1

2 Rear Panel 1

3 Left Panel 1

4 Right Panel 1

5Top Panel - spigot

attached 1

6Black self tapping

screws (Pack of 30) 1

7 Ceiling Ring 1

8 Plastic gromet 1

The replace will require the I30X ex liner ue kit together with 8inch solid ue to encase the

exible ue up to the cowl. More information on page 7

Page 2

i30-X Base - Linear and Stretch

Components

Ref Description QTY

1 Base 1

2 Rear Panel 1

3 Left Panel 1

4 Right Panel 1

5 Top Panel 1

6Black self tapping screws (Pack of

30) 1

7 Nuts for securing top panel to sides 6

NOTE: If installing the replace on either the linear or stretch base, assemble the base rst and then

assemble the casing on top. There are 4 locating holes on both part #5 (top panel of the base)

and part #1 of the freestanding case that should be used to secure the two together using the

supplied screws

Linear pedestal width - 805mm

Stretch pedestal width - 1105mm

Page 3

i30-X Linear and stretch base

Assembly instructions

Step1.

Unbox the base and identify each component

using the table on page 3.

Step 2.

Locate and position the top panel on a clean

and at surface upside down.

The side panels are attached using the supplied

nuts (x6) which are xed to captive welded bolts

on the inside of the top panel.

Step 3.

Identify the left and right side panels. Each side

panel will have a larger return on the front side

and bolt holes that line up to the top panel

captive bolts.

Fit the side panels one at a time by positioning

them onto the top panel rst and sliding on to

the captive bolts. Then tighten the nuts as

shown.

Step 4.

Locate and position the rear panel.

The panel will t between the base vertical return

and is xed in place using the supplied black

screws

NOTE: A PH1 size bit is best suited to the screw

head size.

Step 5.

Locate and secure the base panel with the

supplied screws.

Once the base is secured, ip the base back

over to begin assembly of the case.

Page 4

i30-X Freestanding case

Assembly instructions

Step1.

Unbox the freestanding case and identify each

component using page 2 as reference.

Step 2.

Locate and position the base panel on a at

and slightly elevated working surface. The base

panel front is the at edge.

If using one of the matching bases (linear or

stretch) x this panel to the top of the base using

the 4 pre-drilled holes now.

Step 3.

Identify the left and right side panels. Each side

panel will have a return which will be at the back

of the case.

Fit the side panels one at a time by positioning

them to the inside lip of the base panel, lining up

the pre-drilled holes and screwing into place

using the supplied black screws. Leave the front

screws out at this time otherwise the unit won’t

slide in easily.

NOTE: A PH1 size bit is best suited to the screw

head size.

Step 4.

Locate and position the rear panel.

The panel will t between the base vertical return

and the side panel returns and should be tted

with the electrical and gas cut outs on the left

side of the replace nal position

Once the pre-drilled holes are lined up, screw it

together.

Page 5

i30-X Freestanding case

Assembly instructions

Step 5.

Position the top panel in place and line up the

pre-drilled holes.

It will be a snug t and gentle persuasion may

be required.

NOTE: before applying extreme downward

force to the case, ensure there is no part of the

back of side panels sitting outside the area of

the top panel. Excessive force may damage

the nished product.

Step 6.

Screw the top panel into place and position in

the desired location for unit installation.

Fix the base to the oor using relevant materials.

Clearance requirements

50mm rear clearance

1000mm clearance above

Plan view

Front view

Page 6

50mm side clearance

50mm clearance

to ue

Refer to current i30-X AU manual for oor protection requirements

Zero clearance required under the casing

i30-X Freestanding case

Assembly instructions

Drill 6 holes to ventilate

10 ¹⁄� casing

Step 7.

Mark the ceiling for the ue penetration using a

plumb bob or laser guide and rivet together the

unpainted 8inch gal. If the exposed ue

requires xing, black rivets are recommended.

NOTE: Do not use screws as they can damage

the exible ue.

Step 8.

Install the ue maintaining 50mm clearance to

combustible material through ceiling space

and connect over to the freestanding case

spigot.

Use the supplied celing ring to cover the ceiling

penetration gap and afx with hi temp silicone.

If the 8inch solid ue is passing through a ceiling

space, storage area or a location where blow-

in insulation is used, add an additional 10 ¼

ventilated ue pipe (cut to required size) and a

locating plate to maintain the required 25mm

clearance to the 8inch pipe. Use 15mm self

tapping screws to ensure spacing is consistent.

Drill 6 holes at the base of the outer pipe to

ventilate the casing. This must be left open at

the top.

Step 9.

Feed the exible ue down through the solid

8inch pipe and connect to the removable

spigot as per below inside the free standing

case.

Optional shielding if required

VIS-101/4-GAL-FL

VIS-CHIM-PLATE

Feed through casing spigot

Page 7

Spacer screws

i30-X Freestanding case

Assembly instructions

It is recommended that the bottom 100mm of

the i30X unit is sprayed with hi-temp black paint

prior to tting to the freestanding case. This is to

ensure no silver metal is visible through the

ventilation slots on the side of the free standing

casing.

Step 10.

Position the i30-X replace into the casing on an

angle so as to be able to feed both the exible

gas line and power cord through the back

panel.

Feed the exible gas line out through the rear

panel rectangular hole and the power cord

through the fold out tab. Ensure to use the

supplied rubber gromet to protect the power

cord.

Step 11.

Straighten the unit within the casing and

connect the exible ue slide plate assembly to

the unit whilst pushing the unit into the casing.

Screw in and tighten the slide plate locking

screw.

Step 12.

Insert the two screws on the front of the side

panels that were left out from step 3.

This ensures the rebox cannot slide forward out

of the enclosure after installation.

Step 13.

Connect gas and power and follow the

commissioning procedures for the replace

outlined in the general installation instructions.

The DF front assembly is used to nish the nal

product. The unit should be positioned and lined

up so the decorative front assembly is centered

and ush with the outer casing.

Page 8

Page 9

Page 10

If an offset is required below the

ceiling, the painted 8inch ue must be

riveted together and appropriately

braced within the ceiling cavity

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo TRUE-36G-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-X-AU-L Bedienungsanleitung

Heat & Glo

Heat & Glo RUTHERFORD-42 Bedienungsanleitung

Heat & Glo

Heat & Glo Dakota 42-B Bedienungsanleitung

Heat & Glo

Heat & Glo Rutherford-42 Bedienungsanleitung

Heat & Glo

Heat & Glo STELLAR 3-SS-20-G Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRS-CE Montageanleitung

Heat & Glo

Heat & Glo COSMO-I30-C Bedienungsanleitung

Heat & Glo

Heat & Glo SL-350TRS-CE-D Montageanleitung

Heat & Glo

Heat & Glo ST-36TRB-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo Escape-36DV Bedienungsanleitung

Heat & Glo

Heat & Glo SL-3X-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo REVO-V12 Bedienungsanleitung

Heat & Glo

Heat & Glo TIARAP-AL Bedienungsanleitung

Heat & Glo

Heat & Glo TIARII-BK-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CLX-IFT-S Bedienungsanleitung

Heat & Glo

Heat & Glo Paloma Bedienungsanleitung

Heat & Glo

Heat & Glo ST-550T-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo RHW-51 Bedienungsanleitung

Heat & Glo

Heat & Glo 8000TV-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo PRIMO48-CF Bedienungsanleitung

Heat & Glo

Heat & Glo Soho24 Bedienungsanleitung

Heat & Glo

Heat & Glo EM-415 Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Heat & Glo i30-X Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken