Heat & Glo SL-550TRSI-AUE Bedienungsanleitung

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

MODEL:SL-550TRSI-AUE

AUSTRALIAN GAS ASSOCIATION APPROVED

ApprovalNumber5666

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044 USA • 1-888-427-3973

INSTALLATION AND OPERATION

INSTRUCTIONS

THIS PRODUCT MAYBE COVERED BY ONE OR MORE OFTHE FOLLOWING PATENTS:

(UnitedStates)4593510,4686807,4766876,4793322,4811534,5000162,5016609,5076254,5113843,5191877,5218953,5263471,5328356, 5341794, 5347983, 5429495, 5452708,5542407,

5601073,5613487,5647340, 5688568,5762062,5775408, 5890485,5931661,5941237, 5947112,5996575, 6006743,6019099,6048195, 6053165,6145502, 6170481,6237588,6296474,

6374822,6413079,6439226,6484712,6543698,6550687,6601579,6672860,6688302B2,6715724B2,6729551,6736133,6748940,6748942,D320652,D445174,D462436;(Canada)1297749,

2195264,2225408;

(Australia)543790;586383;(Mexico)97-0457;(NewZealand)200265;

orotherU.S.andforeignpatentspending.

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

IMPORTANT: Read all instructions carefully before starting installation.

Failuretofollowtheseinstallationinstructions may result ina possible fire

hazard and will void the warranty. Save this Manual for future reference.

MODEL SL-550TRSI-AUE

ISAUSTRALIAN GASASSOCIATION

APPROVED FOR NATURAL GAS OR

PROPANE AS A BALANCED FLUE

HEATER.

Refer to the appliance data plates for gas

consumptionsand pressures.

Installationof this appliance should only be

carried out by an authorized person in ac-

cordance with the manufacturer's instruc-

tions.Applianceistobeinstalledinfull com-

pliance with the National Gas Installation

Standard AS5601, the manufacturer's in-

structions,andanylocalauthorities'require-

mentsforgas,electricaland building regu-

lations.

This appliance and its components are

tested and safe when installed in accor-

dancewiththisInstallationManual.Report

to your dealer any parts damaged in ship-

ment,specificallycheckglasscondition.The

gas logs and flue system components are

inseparatepackages. Readallinstructions

beforestartinginstallationandfollow these

instructions carefully during installation to

ensure maximum benefit and safety. Fail-

uretofollowthemwillvoidyourwarrantyand

maypresent a fire hazard.

TheHeat& Glo, a brand of Hearth &Home

TechnologiesInc.warrantywillbevoidedby,

and Heat & Glo, a brand of Hearth & Home

TechnologiesInc.disclaimsanyresponsibil-

ityfor the followingactions:

• Installation of any damaged heater or

fluesystemcomponent

• Modification of the heater or balanced

flue system installation other than as

instructed by Heat & Glo, a brand of

Hearth& HomeTechnologies Inc.

• Improper positioning of the gas logs or

theglassdoor

• Installationand/oruseofanycomponent

part not manufactured or approved by

Heat & Glo, brand of Hearth & Home

TechnologiesInc.,not withstanding any

independent testinglaboratory or other

party approval of such componentpart

oraccessory.

PLEASEREADTHISMANUALBEFOREINSTALLING

ANDUSINGTHISAPPLIANCE.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA

Heat & Glo Quality Systems

registered by SGS ICS

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

TABLE OF CONTENTS

1.0 InstallationInstructions.........................................................................................5

1.1 Introduction...................................................................................................6

1.2 Flue SystemApprovalsand Installation .........................................................8

1.3 Connecting theGasSupply ........................................................................22

1.4 Ignition SystemWiring ................................................................................23

1.5 BlowerFan.................................................................................................24

1.6 Finishing ....................................................................................................25

1.7 InstallerTesting ...........................................................................................26

1.8 LogPlacement ...........................................................................................27

2.0 OperatingInstructions .......................................................................................30

2.1 Safetyand LightingInformation...................................................................31

2.2 FanOperation ............................................................................................32

3.0 Servicingand Maintenance...............................................................................32

3.1 RemovalofCoversforServicing ................................................................33

3.2 RemovalofComponentsforService ..........................................................33

3.3 PartsReplacement.....................................................................................33

3.4 Adjustmentsand Replacement Parts ..........................................................33

3.5 MaintenanceTasks.....................................................................................34

3.6 Troubleshooting..........................................................................................35

4.0 ReplacementParts ...........................................................................................37

LimitedWarranty...............................................................................................39

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Figure 1. Diagram of SL-550TRSI-AUE

25-3/4 in.

(653mm)

12-7/8 in.

(327mm)

15-7/8 in.

(402mm) 16-3/8 in.

(414mm)

8-3/4 in.

(223mm)

Ø 82 in.

(203mm)

36-3/8 in.

(924mm)

GAS LINE

ACCESS

6 in.

(153mm)

2-1/8 in.

(55mm)

32 in.

(813mm)

36 in.

(913mm)

16-1/8 in.

(408mm) 3-1/2 in.

(90mm)

6-7/8 in.

(175mm)

26-3/8 in.

(671mm)

31-1/8 in.

(790mm)

Ø 6-1/2 in.

(165mm)

32-5/8 in.

(828mm)

ELECTRICAL

ACCESS

23-3/8 in.

(593mm)

TOP STANDOFFS

FLUE COLLAR

COVER PLATE

HOOD

DATA BADGE

& LABELS

DRESS

GUARD

ACCESS

DOOR

GAS

CONTROLS

ELECTRICAL

ACCESS

GAS LINE

ACCES

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Figure 2. Fireplace Dimensions, Locations, and

Space Requirements

Minimum Clearances

from the Fireplace to Combustible Materials

Inches mm

Glass Front......................................36........ 914

Floor .................................................0........... 0

Rear ................................................ 1/2 ........ 13

Sides .............................................. 1/2 ........ 13

Top ................................................1 1/2....... 38

Ceiling* ............................................31........ 787

For minimum clearances, see the direct vent termina-

tion clearance in Figures 23 and 28.

Minimum Clearances

from the Vent Pipe to Combustible Materials

Inches mm

Vertical Sections. ............. 1 ................ 25

Horizontal Sections

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

At Wall Firestops

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

*The clearance to ceiling is measured from the top

of the unit, excluding the standoffs (see Figure 30).

1” MIN. (25mm)

1/2” MIN. (12.5mm)

Theheater canbe mounted onany ofthe following sur-

face:

1. Aflat surface(minimum 6mm base).

2. Four(4) cornersupports.

(Example: Four (4) concrete masonry blocks). These

supportsmust be positionedso they contact all four (4)

perimeter edges on the bottom of the unit.

Heaterframing can bebuilt before or after the heater is

set in place. Framing should be positioned to accom-

modate wall covering and heater facing material. The

heaterframing should beconstructed of2 inch X4 inch

(51 x 102mm) lumber or heavier. The framing headers

mayrest on the heater standoffs. Refer toFigure 2 and

Figure3 forheater andframing referencedimensions.

A B C D E

Inches 37 16-1/4 29-1/2 41-3/4 59

Millimeters 940 413 749 1060 1499

A B C D E

Inches 37 16-3/8 33 46-11/16 66

Millimeters 940 413 838 1186 1676

Top Flue

Rear Flue

1.0 INSTALLATION INSTRUCTIONS

In planning the installation for the heater it is neces-

saryto determine where the unit is to be installed, the

type of flue system to be used (straight out, corner, or

elevated), and whether optional accessories (wall

switchorremote control)are desired. Gassupply pip-

ingshouldalsobe planned.Refertotheappliance data

plate on the base pan of the heater for all gas pres-

suresand input rateinformation.

NOTE: Notintended forfireplace insert.

1” MIN. (25mm)

3” (76mm)

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Figure 3. Framing Dimensions

Framing should be constructed

of 2 X 4 lumber or heavier.

The framing headers

may rest on the

fireplace stand-offs.

ABCD*E*

37 in. 33-1/4 in. 16-1/2 in. 43-3/4 in. 23-3/8 in.

(940mm) (845mm) (420mm) (1111mm) (594mm)

*NOTE: The center of the framing hole is one inch

(254mm) above the center of the horizontal flue pipe.

CAUTION: Measure heater dimensions, and

verifyframingmethods and wallcoveringdetails be-

foreframing constructionbegins.

1.1 INTRODUCTION

This model is designed to operate with all com-

bustion air being siphoned from the outside of the

building and all exhaust gases expelled to the

outside of the building.

WARNING: THIS UNIT IS NOT FOR USE WITH

SOLID FUEL.

TheseunitsMUSTusetheflueterminationdescribed

in the flueing section of the manual.

The control system for this model is an electronic igni-

tiontype.It consistsof a gascontrol valve/variable regu-

lator, a pilot/sensor/electrode and an ON/OFF switch.

The controls are located behind the access door. Ro-

tate the door down to open. See Figure 1.

Minimuminlet gas supplypressure for purposeof input

adjustment is 4.5 inches w.c. (1.13kPa) for natural gas

and11inchesw.c.(2.75kPa)for propane.Manifold(out-

let) pressures should be set at 3.5 inches w.c. (.8kPa)

fornatural gasmodelsand 9.5inches w.c. (2.36kPa)for

propanemodels.

NON-COMBUSTIBLE ZONE

IS DEFINED BY 76MM ABOVE THE

ELBOW FOR THE ENTIRE

WIDTH AND DEPTH (BEHIND THE

FRONT HEADER) OF THE FIREBOX.

76mm

38mm

WALL STUD

FLUE

FRAMING

HOLE

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a flue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a flue

terminal to a LP Gas cylinder. A flue terminal is considered to be a source of ignition.

MINIMUMCLEARANCESREQUIREDFORBALANCEDFLUETERMINALS

ORTHEFLUE TERMINALSOFOUTDOORAPPLIANCES

Figure 4

CLEARANCES 'n' (mm)

Space heaters All other appliances

Up to 50 MJ/h

input UP to 50 MJ/h

input Over 50 MJ/h &

to 150 MJ/h

Over 150 MJ/h

input

150 500 1000 1500

T = Flue terminal M = Gas meter Shading indicates prohibited

I = Mechanical air inlet P = Electricity meter or fuse box areas for flue terminals

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances to 50 MJ/h input ................................................................................................ 300

Appliances over 50 MJ/h input ............................................................................................ 500

b - From the ground or above a balcony...................................................................................... 300

c - From a return wall or external corner ..................................................................................... 500

d - From a gas meter (M) ...........................................................................................................1000

e - From an electricity meter or fuse box (P) ............................................................................... 500

f - From a drain or soil pipe......................................................................................................... 150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal ......................................................... 500

h - From any other flue terminal, cowl, or combustion air intake ............................................... 500

j - Horizontally from an openable window, door, non-mechanical air

inlet, or any other opening into a building, with the exception of

sub-floor ventilation:

Appliances up to 150 MJ/h input ......................................................................................... 500

Appliances over 150 MJ/h input ........................................................................................ 1500

k - From a mechanical air inlet, including a spa blower .........................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of ................................. See table

sub-floor ventilation............................................................................................................. below

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

TABLE1

1.2 FLUE SYSTEM APPROVALS

Thesemodels haveflue starting collarson boththe top

and the back of the unit. Depending upon the installa-

tion, decide which ONE set of starting collars will be

usedto attach theflue system. Thestartingcollarsealing

cap must remain on the starting collar NOT used.

Thesemodels useSL-D-series directflue components

whenusing theTOP flue collarsand DVP-series direct

flue components when usingthe REAR fluecollars.

WARNING: YOU MUST NOT MIX DVP-SERIES

AND SL D-SERIES COMPONENTS IN ANY FLUE

SYSTEM CONFIGURATION.

Approved flue system components are labeled for

identification. NO OTHER FLUEING SYSTEMS OR

COMPONENTS MAY BE USED. Detailed installation

instructions are included with each flue termination kit

andshouldbeusedinconjunctionwiththismanual.Figure

5belowshowsfluesystemcomponentsandterminations.

Identifying Flue Components

The flue systems installed on this gas fireplace may

include one, two, or three 90°elbow assemblies. The

relationships of vertical rise to horizontal run in flue

configurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown in

theflueing drawingsand tables onthe next fewpages.

WARNING:THIS GASAPPLIANCEAND FLUEAS-

SEMBLY MUST FLUE DIRECTLYTO THE OUTSIDE

AND MUST NEVER BE ATTACHED TO A CHIMNEY

SERVINGA SEPARATE SOLID FUELBURNING AP-

PLIANCE. EACH GAS APPLIANCE MUST USE A

SEPARATE FLUE SYSTEM-COMMON FLUE SYS-

TEMSAREPROHIBITED.

CAUTION: UNDER NO CONDITION SHOULD

COMBUSTIBLE MATERIAL BE CLOSER THAN 3

INCHES (2 1/2 INCHES (64MM) AT WALL FIRE-

STOPS) FROM THE TOP OF THE PIPE OR 1-INCH

TOTHESIDESANDTHEBOTTOMFORHORIZONTAL

SECTIONS OF THIS FLUE SYSTEM. VERTICAL

SECTIONS OF THIS SYSTEM REQUIRE A MINI-

MUM OF 1-INCH (25MM) CLEARANCE TO COM-

BUSTIBLE MATERIALSALLAROUND THE PIPE.

For alternative installations, other than depicted, con-

tactyour dealer forfurther information.

Refer to Figure 4 for required clearances to flue terminals.

Flue system termination kits

Flue system components

Figure 5. Flue Components and Terminations

MODEL

SL-550TRSI-AUE DVP-TRAP2 & SLK-01TRD HORIZONTALTERMINATIONCAP

DVP-TVHW & SLK-991DA VERTICALTERMINATION CAP

FLUE TERMINATION APPROVALS

ERTICAL

TERMINATION

HORZONTAL

TERMINATION

WALL

FIRESTOP

STORM

COLLAR

ROOF FLASHING

HORIZONTAL PIPE

SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING

FIRESTOP

90 DEGREE

ELBOW

SLK-01TRD SLK-991DA DVP-TVHW DVP-TRAP2

DVP-SERIESSL D-SERIES

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

NOTE: PIPES OVERLAP 32mmAT EACH JOINT.

DVP90ST

319mm

286mm

184mm

32mm TYP

13mm TYP

217mm

DVP36

DVP48

1219mm

610mm

914mm

102mm

152mm

DVP4

DVP6

305mm

DVP12

51mm

MIN.

DVP12A

310mm

MAX.

DVP24

251mm

45.0

260mm

DVP45

362mm

Figure 6. DVP-Series Balanced Flue Component Specifications

(127mm inner pipe / 203mm outer pipe)

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Figure 7. SL D-Series Balanced Flue Component Specifications

(4-inch (102mm) inner pipe / 6 5/8-inch (168mm) outer pipe)

NOTE: PIPES OVERLAP1 3/8 INCHES (35mm)AT EACH JOINT.

6 5/8

(168mm)

9 5/8

(244mm)

6 3/8

(162mm)

6 3/8

(162mm) 6 ½

(165mm)

9 5/8

(244mm)

SL-90D

6 ½

(165mm)

6 5/8

(168mm)

5 ¾

(146mm)

11 ¾

(298mm)

SL-06D SL-12D SL-17/24D

17-24

(432-610mm)

SL-09D SL-12/17D SL-24D SL-36D SL-48D

8 ¾

(222mm)

12-17

(305-432mm)

23 ¾

(603mm)

35 ¾

(908mm)

47 ¾

(1213mm)

Andere Handbücher für SL-550TRSI-AUE

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo REVO-V12 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TRSI-AUC Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-42D Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-C (COSMO) Bedienungsanleitung

Heat & Glo

Heat & Glo SLR32 Bedienungsanleitung

Heat & Glo

Heat & Glo LCOR-HVB-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo RUTHERFORD 50-B Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IFTLP-S Bedienungsanleitung

Heat & Glo

Heat & Glo ESCAPE-30LP-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo LOGS-2531 Bedienungsanleitung

Heat & Glo

Heat & Glo FB-ZC Bedienungsanleitung

Heat & Glo

Heat & Glo 6000CL-IFT-S Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550METRO-LP Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-42 Bedienungsanleitung

Heat & Glo

Heat & Glo CF230E-B Bedienungsanleitung

Heat & Glo

Heat & Glo REVO-V12 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000TR-OAK Bedienungsanleitung

Heat & Glo

Heat & Glo SLR-B (COSMO) Bedienungsanleitung

Heat & Glo

Heat & Glo Cosmo SLR Bedienungsanleitung

Heat & Glo

Heat & Glo GRAND-I35-C Bedienungsanleitung

Heat & Glo

Heat & Glo HST48D Bedienungsanleitung

Heat & Glo

Heat & Glo MEZZO36 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch