Henny Penny OFE-341 Betriebsanleitung
Model OFE/OFG/OEA/OGA-341, 342
5-1. TROUBLE SHOOTING GUIDE
Problem Cause Correction
POWER switch ON but fryer • Open circuit • Plug fryer in
completely inoperative
•Check breaker or fuse at supply
box
Shortening will not • Open high limit •Reset high limit per
heat but lights are on. circuit High Limit Temperature
Error message “E10” Control Section
• Drain valve open •Turn drain valve handle to
Error message “E15” closed position
Foaming or boiling • Water in shortening •At end of Cook Cycle, drain
over of shortening shortening and clean
• Improper or bad •Use recommended shortening
shortening
• Improper filtering •Refer to the procedure covering
filtering the shortening
• Improper rinsing after •Clean and rinse the frypot, then
cleaning the fryer dry thoroughly
Shortening will not • Drain valve clogged •Open valve, force cleaning
drain from frypot with crumbs brush through drain
Filter switch on, • Motor thermal •Reset thermal switch per section
motor does not run protector tripped on Filter Pump Motor
Protector – Manual Reset
More detailed troubleshooting information is available in the Technical Manual, available at
www.hennypenny.com, or 1-800-417-8405 or 1-937-456-8405.
903 5-1
SECTION 5. TROUBLESHOOTING
Model OFE/OFG/OEA/OGA-341, 342
5-2. ERROR CODES In the event of a control system failure, the digital
display will show an "Error Message." These
messages are coded: “E4”, “E5”, “E6”, “E10”,
“E15”, “E20”, “E-31”, “E41”, “E46”, “E54”,
E-70-A & B and “E92”. A constant tone is heard
when an error code is displayed, and to silence this
tone, press any button.
DISPLAY CAUSE PANEL BOARD CORRECTION
“E-4” Control board Turn switch to OFF position, then turn switch back to ON.
overheating if display shows “E-4”, the control board is getting too hot;
check the louvers on each side of the unit for obstructions
“E-5” Shortening Turn switch to OFF position, then turn switch back to ON;
overheating if display shows “E-5”, the heating circuits and temperature
probe should be checked
“E-6 A” Temperature Turn switch to OFF position, then turn switch back to ON;
probe open if display shows “E-6”, check the temperature probe;
to replace, refer to Technical Manual
“E-6 B” Temperature Turn switch to OFF position, then turn switch back to ON;
probe shorted if display shows “E-6” check the temperature probe;
to replace, refer to Technical Manual
“E-10” High limit Reset the high limit by manually pushing up on the reset
button; if high limit does not reset, high limit must be
replaced; refer to Technical Manual
“E-15” Drain switch Close drain, using the drain valve handle; if display still
failure shows “E-15”, check the drain microswitch; refer to
Technical Manual
“E-41”, Programming Turn switch to OFF, then back to ON; if display shows any
“E-46” failure of the error codes, try to reinitialize the control (Special
Program Section) if error code persists, replace the control
board; refer to Technical Manual
5-2 808
Model OFE/OFG/OEA/OGA-341, 342
5-2. ERROR CODES
(Continued)
DISPLAY CAUSE PANEL BOARD CORRECTION
“E-20 A” Vacuum Press the timer button to try the ignition process again;
switch failure if “E-20 A” persists check vacuum switch; refer to
(stuck closed) Technical Manual
“E-20 B” Draft fan or Press the timer button to try the ignition process again;
vacuum if “E-20 B” persists, check vacuum switch or the blower
switch failure motor; refer to Technical Manual
(stuck open)
“E-20 C” Ignition modules Press the timer button to try the ignition process again; if
not responding “E-20 C” persists, check the ignition
module, the spark ignitor, or the I/O board; refer to
Technical Manual
“E-20 D” Pilots not lit or Press the timer button to try the ignition process again; if
no flame sense “E-20 D” persists, check the ignition module, the I/O
board, or the flame sensor; refer to Technical Manual
“E-31” Elements up- Lower elements into frypot
Electric units only
Fan switch jumper Check for jumper wire on 12-pin connector & add if missing
wire missing
“E-54” PCB component Turn switch to OFF position, then turn switch back to ON;
failure if “E-54” persists, have PCB replaced
“E-70A” Fan switch jumper Have jumper wire checked on 12 pin connect to panel
missing
“E-70B” MV jumper missing Have jumper wire checked on connectors to panel
“E-92” 24 VAC fuse 24 VAC fuse on I/O board open; check for shorted
on I/O open component in 24-volt circuit (i.e.., hi limit, drain switch,
air switch)
908 5-3
Andere Handbücher für OFE-341
1
Dieses Handbuch passt für folgende Modelle
8
Andere Henny Penny Fritteuse Handbücher
Henny Penny
Henny Penny OFG-390 Bedienungsanleitung
Henny Penny
Henny Penny 581 Bedienungsanleitung
Henny Penny
Henny Penny 322 Bedienungsanleitung
Henny Penny
Henny Penny Pressure Fryer Bedienungsanleitung
Henny Penny
Henny Penny 500 Bedienungsanleitung
Henny Penny
Henny Penny FS-100 Bedienungsanleitung
Henny Penny
Henny Penny EVOLUTION ELITE EEG-242 Bedienungsanleitung
Henny Penny
Henny Penny OFE-290 Bedienungsanleitung
Henny Penny
Henny Penny PFE-500 Bedienungsanleitung
Henny Penny
Henny Penny OFE-321 Betriebsanleitung
Henny Penny
Henny Penny LOV LVE-100 Series Bedienungsanleitung
Henny Penny
Henny Penny FDS-200 Bedienungsanleitung
Henny Penny
Henny Penny OFE-341 Bedienungsanleitung
Henny Penny
Henny Penny GVE-071 Bedienungsanleitung
Henny Penny
Henny Penny F5 Bedienungsanleitung
Henny Penny
Henny Penny 8000 Computron Betriebsanleitung
Henny Penny
Henny Penny OFG-390 Bedienungsanleitung
Henny Penny
Henny Penny LVG-202 Bedienungsanleitung
Henny Penny
Henny Penny PFE-590 Referenzhandbuch
Henny Penny
Henny Penny 580 KFC Bedienungsanleitung
