HiB Laser Bedienungsanleitung

(Fig1)

Thank you for purchasing this HiB product.

Please read through these instructions carefully and refer back to them during installation to ensure that

your product is tted safely and that it retains its high quality nish.

Please retain this leaet for future reference.

Before drilling, ensure there are no hidden cables or pipes in the wall.

Parity & Laser Recessed Cabinets

FI #02 002 R150907 Ver No. 1.0 Jan 2016

Please Note

This product can be tted into a partition wall, or wall hung. Before installing

ensure you take note of measurements of recessed area or mounting points (See

g. A).

This product must be installed with a minimum distance of 150mm between

the infra-red sensor switch and any adjacent wall or object to ensure correct

operation of the sensor.

You may need to remove the door / doors to make it easier to t. This can be

done by unclipping the hinges. (There is a release catch at the back of the hinge).

DO NOT FIT SHELVES AT THIS STAGE.

Laser

Art No. 44300

Parity

Art No. 44200

Hanger Adjustment (Fig C)

Fixing Preparation (Fig A)

Fixing Brackets (Fig B)

Wall Hung Installation

1. Position the cabinet in a suitable location, (according to the zonal diagram (Fig. 1) on the back page),

ensuring that the domestic electrical mains supply is within reach of the electrical connection point

of the cabinet. Carefully mark the position of the top of the cabinet using a soft pencil.

2. Remove the cabinet from the wall and using a spirit level, mark a horizontal line below the pencil

mark, taking into account the location of the mounting points. Place brackets on the new line paying

attention to the distance of the mounting points. Mark the position of the holes using a soft pencil.

(See g. A).

3. Before drilling, ensure there are no hidden cables or pipes behind the mounting points. Drill the

required holes in the marked positions. If drilling through tile, use a ceramic drill bit. Insert the wall

plugs level with the surface of the wall. If tting to a tiled surface, wall plugs should be inserted

below the tile surface to avoid cracking. NB. For plasterboard walls, specialist xings should be

purchased, available from any DIY or hardware store.

4. Fix the bracket to the wall using the screws provided. (See Fig. B).

5. Open the cabinet door(s) and remove screws on front edge of the internal panel at the top. Place

screws in a safe place.

6. Temporarily hang the cabinet ensuring claws on the hangers are securely located on the wall

brackets. Using a spirit level adjust the angle of the cabinet via the screws on hangers (See Fig. C).

using a drill create a suitable hole for an internal xing hole inside the cabinet (see Fig. A) and mark

all. Then remove cabinet from wall.

7. Drill a suitable hole in the marked location and t a wall plug (taking into account step 3).

8. Connect the domestic mains supply according to the wiring diagram (g. 2) on the back page.

9. Rehang cabinet, tighten screw on hangers (See Fig. C) and secure the base of the cabinet with

supplied screw & screw cap.

10. Once fully secure, close the internal top cover and secure with screws removed earlier.

11. Starting with the top shelf, insert the shelf supports in desired position and t shelves (See Fig. F).

12. Door(s) can be adjusted if required via screws on hinges. (See Fig. G).

13. Switch mains supply back on.

Recessed Area

Mounting Points

REAR VIEW

Angle

Adjustment

Claw In/Out

Adjustment

hib.co.uk 3

Recessed Installation

Before installation, ensure the construction of the partition wall is suitable to allow the cabinet to t

tightly into the recess. The cabinet should be placed in a suitable location, (according to the zonal

diagram (Fig. 1) on the back page). Ensure that the domestic electrical mains supply is within reach of the

electrical connection point of the cabinet.

1. Remove caps using a suitable screw driver, then remove diusers & light tubes. (See g. D).

2. Position the cabinet in the recess, and mark the positions of the xing holes of the cabinet using a

soft pencil. Then remove from wall.

3. See stage 3 of the wall hung installation process opposite.

4. Connect the domestic mains supply according to the wiring diagram (Fig. 2) on the back page.

5. Slot cabinet into recess and using a suitable screwdriver, screw cabinet onto stud wall. (See Fig. E).

6. Replace lighting tubes & diusers and replace top & bottom caps with supplied square caps for

recessed mounting. (See g. D2).

7. Follow stage 11 to 13 of the wall hung installation process opposite to complete installation.

Operating Instructions

To turn illumination on or o, wave hand past the sensor switch on the right side of the cabinet.

To operate charging socket, use pull cord located next to socket. Socket is suitable for recharging

toothbrushes, shavers and trimmers. NB. On rst use of the charger socket, reasonable force may be required

to fully insert the plug. Hold the cabinet rmly so that it is not pushed o the wall. After a few uses, stiness will

ease.

Lamp Replacement

Requires 2x T4 lamps, Max 22W

CAUTION: Allow at least 30 minutes after lamp failure before replacing. Ensure the domestic electrical

mains supply to which the product is connected is turned o.

1. Remove top or bottom caps using a suitable screw driver. Then remove diusers & light tubes.

2. Place new lighting tubes, then replace diusers and top or bottom caps.

Replace Caps & Diusers (Fig D)

Fixing into recess (Fig E)

Shelf Adjustment (Fig F)

Move door(s) up/down

Move door away/towards

the cabinet

Move door(s) left/right

Door Adjustment (Fig G)

1. 2.

This product is suitable for installation in zones: 2 &Outside Zone

All installations must comply with guidelines which are based on a zonal concept. The diagram above

illustrates this concept and must be followed to ensure the safe installation of electrical appliances in the

bathroom. These regulations apply to domestic installations only. Installations must be made in accordance

with the current IEE wiring regulations and relevant building regulations. HiB recommends that all electrical

bathroom products should only be tted by a suitably qualied, Part P registered electrician.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and

make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specications as necessary. E & OE.

T: +44 (0)20 8441 0352 F: +44 (0)20 8441 0219 E: [email protected]o.uk hib.co.uk

Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN

(Fig1)

Wiring Diagram (Fig 2)

live

earth

neutral

MAINS SUPPLYLUMINAIRE

Live supply can be Red or Brown

Earth supply is Green and Yellow

Neutral supply can be Blue or Black

Live is Brown

Earth is Green and Yellow

Neutral is Blue

Electrical Safety Information

HiB recommends that all electrical bathroom products should only be tted by a suitably qualied, Part P

registered electrician in accordance with current IEE regulations. Ensure mains power supply is switched

o before starting installation. Before drilling, ensure there are no hidden cables or pipes in the wall.

Care Instructions

Do not use abrasives or solvents when cleaning this product.

Wipe o all water spillages as soon as possible using a soft, damp cloth.

Aftercare Service

In the unlikely event that this product should fail please contact HiB customer services, contact detail

shown below.

WEEE Compliance

Must not be mixed with

general household waste.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HiB Inneneinrichtung Handbücher

HiB

HiB Novum Duet Bedienungsanleitung

HiB

HiB Vogue Bedienungsanleitung

HiB

HiB Proton Bedienungsanleitung

HiB

HiB novum Bedienungsanleitung

HiB

HiB novum NF02S3DRT30 Series Bedienungsanleitung

HiB

HiB Connect Series Bedienungsanleitung

HiB

HiB Novum N18DU60MWH Bedienungsanleitung

HiB

HiB Arcane Curve 50 Black 79500100 Bedienungsanleitung

HiB

HiB Verve 50 Cabinet Bedienungsanleitung

HiB

HiB Qubic 50 Bedienungsanleitung

HiB

HiB Austin Bedienungsanleitung

HiB

HiB Groove 50 Bedienungsanleitung

HiB

HiB Vanquish 50 Bedienungsanleitung

HiB

HiB Novum NF02SBU50 Series Bedienungsanleitung

HiB

HiB Ether 50 50500 Bedienungsanleitung

HiB

HiB Essence 50 Bedienungsanleitung

HiB

HiB NOVUM Camber Bedienungsanleitung

HiB

HiB Dusk 50 Bedienungsanleitung

HiB

HiB NOVUM N19FS50MBL Bedienungsanleitung

HiB

HiB Atrium 50 Bedienungsanleitung

HiB

HiB novum N19WH50MBL Bedienungsanleitung

HiB

HiB austin 9101900 Handbuch

HiB

HiB Paragon 50 Bedienerhandbuch

HiB

HiB Vapor 50 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung