HighPoint RocketMate 220 Bedienungsanleitung

Revision History

RocketMate 220

2.5" Dual-M.2 Driverless & Bootable NVMe RAID Enclosure

Quick Installation Guide

V1.00

Table of Contents

Introducing the HighPoint RocketMate 220............................................. 3

Kit Contents ............................................................................................. 3

System Requirement................................................................................ 3

Board Layout............................................................................................ 4

Hardware Installation............................................................................... 6

RAID Switch Setting.................................................................................. 9

Certified Cable Accessories.................................................................... 11

Customer Support.................................................................................. 13

Introducing the HighPoint RocketMate 220

HighPoint’s RocketMate 220 is a driverless, bootable 2.5" NVMe RAID

enclosure designed for use with PC platforms. It can be installed into any

industry-standard 2.5" drive bay, tray, backplane or mobile rack with an

SFF-8639 connector. It is natively supported by all modern PC Virtual

Machine and Operating System platforms including VMware, Proxmox,

Hyper-V, Windows and Linux.

Kit Contents

⚫1x RocketMate 220 M.2 NVMe Enclosure

⚫1x Quick Installation Guide

⚫1x N1C-323140-1110 (use for deleting RAID arrays)

⚫1x N1C-800250-4110 (use for RAID Switch)

⚫1x N1C-300800-4110 (use for installing or removing screws)

System Requirement

⚫Windows 11 and 10, Windows Server 2016, 2019 and 2022,

Microsoft Hyper-V

⚫Linux Kernel v3.10 and later

⚫VMware, Proxmox

Board Layout

RAID LED Indicator

SFF-8639 connector

RAID Switch

RAID Setting

RAID Delete Switch

RAID LED Indicator Status

RAID Status

RAID Status LED Indicator

RAID0

Solid Green

RAID1

Solid Blue

Single Disk(JBOD) x2

Solid Pink

RAID failure

Solid Red

No Configuration

OFF

RAID Active

RAID creation

Flicker

M.2 M-Key port

mounting

screws

Supported SSD Form Factor：

2280

Energy Unit: Power Loss Protection

Hardware Installation

1. Remove the top panel by unscrewing the 3 screws shown below

(requires a Phillips screwdriver):

2. To install M.2 NVMe SSDs:

01. Remove the screws (shown below).

02. Carefully insert each M.2 SSD into the slot.

03. Fasten down each SSD using the screws removed in step “01”.

2242

2260

Note: Make sure the SSDs are carefully, but securely installed into each

M.2 port. Loose connections can cause a variety of stability and

performance issues, and may ultimately result in data loss.

3. Align the top panel and secure it to the enclosure using the screws

removed in step 1.

Note: Make sure the top panel is aligned properly and secured firmly to

the enclosure. A misaligned or lose panel may prevent the RocketMate

from functioning properly, and/or prevent the enclosure from properly

cooling the M.2 NVMe SSDs. Unsecure connections or overheating may

result in damage to the NVMe media or controller hardware, degraded

performance, or lead to unstable I/O and data loss.

4. Connect the enclosure to the host system using the appropriate cable

(such as the HighPoint M.2-8639-050, shown below):

SATA 15-pin

SFF-8639

RAID Switch Setting

Four options are available. When the system starts; the RocketMate 220

(RM220) will automatically create the specified array using the hosted

NVMe SSDs.

The RAID switch is located at the bottom of the

enclosure (dial).

The dial can be adjusted using the small flat-head

screwdriver included with the RM220.

M.2

RAID Switch

RAID Setting

code

RAID Level

4/9

RAID0

Set the dial to “4/9” – this will create a RAID 0 array after the RM220

is powered on. The LED will glow green.

1/6

RAID1

Set the dial to “1/6” – this will create a RAID 1 array after the RM220

is powered on. The LED will glow blue.

2/7

JBOD x2

Set the dial to "2/7" – this will create two JBOD array after the RM220

is powered on. The LED will glow pink.

3/8

Delete RAID

When the disk is powered on, set the dial code to "3/8", insert the

RAID pin into the “DEL” hole, and press it; the enclosure will flash the

LED twice and delete the array.

Note: The RAID Switch can only be used with SSDs that have not been

configured into an array.

Inhaltsverzeichnis

Andere HighPoint Gehäuse Handbücher

HighPoint

HighPoint RocketStor 6314X Bedienungsanleitung

HighPoint

HighPoint Thunderbolt TurboBox NA211TB Bedienungsanleitung

HighPoint

HighPoint RocketStor 6414TS Bedienungsanleitung

HighPoint

HighPoint RocketStor 6628A Bedienungsanleitung

HighPoint

HighPoint SSD6444M Bedienungsanleitung

HighPoint

HighPoint RocketStor 6614V Bedienungsanleitung

HighPoint

HighPoint RocketStor 6418AS Bedienungsanleitung

HighPoint

HighPoint SSD6540M Bedienungsanleitung

HighPoint

HighPoint RocketStor 6414AS Bedienungsanleitung

HighPoint

HighPoint RocketStor 6418TS Firmware-Update

HighPoint

HighPoint RocketStor 6674T Bedienungsanleitung

HighPoint

HighPoint SSD6540M Bedienungsanleitung

HighPoint

HighPoint RocketStor RS6414AS Bedienungsanleitung

HighPoint

HighPoint RocketStor 6421AS Bedienungsanleitung

HighPoint

HighPoint RocketStor 6614V Bedienungsanleitung

HighPoint

HighPoint RocketStor 6434TS Bedienungsanleitung

HighPoint

HighPoint RocketStor 6421TS Bedienungsanleitung

HighPoint

HighPoint SSD6780M Bedienungsanleitung

HighPoint

HighPoint RocketStor 6628T Bedienungsanleitung

HighPoint

HighPoint RocketStor 6124V Bedienungsanleitung

HighPoint

HighPoint RocketStor 6314A Bedienungsanleitung

HighPoint

HighPoint SSD6540M Bedienungsanleitung

HighPoint

HighPoint RocketStor 6414AS Bedienungsanleitung

HighPoint

HighPoint SSD6540M Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung