HIK VISION Hik IP Receiver Pro Bedienungsanleitung
Hik IP Receiver Pro
User Manual
Legal Informaon and Symbol Convenons
Symbol Convenons
The symbols that may be found in this document are dened as follows.
Symbol Descripon
Danger
Indicates a hazardous situaon which, if not avoided, will or could
result in death or serious injury.
Cauon
Indicates a potenally hazardous situaon which, if not avoided, could
result in equipment damage, data loss, performance degradaon, or
unexpected results.
Note Provides addional informaon to emphasize or supplement
important points of the main text.
Hik IP Receiver Pro User Manual
i
Contents
Chapter 1 Overview .................................................................................................................... 1
1.1 Introducon ........................................................................................................................... 1
1.2 Running Environment ............................................................................................................ 1
Chapter 2 Installaon ................................................................................................................. 2
2.1 Port Instrucon ...................................................................................................................... 2
2.2 Install Hik IP Receiver Pro ....................................................................................................... 3
2.3 Acvate Hik IP Receiver Pro ................................................................................................... 3
Chapter 3 Device Management ................................................................................................... 5
3.1 Add Hikvision Device(s) Managed in Hik-ProConnect ............................................................ 5
3.2 Add Single Third-Party Device ................................................................................................ 6
3.3 Add Third-Party Devices in a Batch ........................................................................................ 6
3.4 Enable Alarm Service and Set Zone ....................................................................................... 7
Chapter 4 Basic Conguraon ..................................................................................................... 9
4.1 Access Hik-ProConnect .......................................................................................................... 9
4.2 System Sengs ...................................................................................................................... 9
4.2.1 Congure Hik IP Receiver Pro Name ........................................................................... 10
4.2.2 Change Password for Admin User ............................................................................... 10
4.2.3 Congure Time ............................................................................................................ 10
4.3 System Maintenance ............................................................................................................ 10
4.4 Network Sengs .................................................................................................................. 11
4.4.1 Edit Port ...................................................................................................................... 11
4.4.2 Set NIC for Hik IP Receiver Pro .................................................................................... 12
4.4.3 Set NAT ........................................................................................................................ 12
4.4.4 Set HTTPS .................................................................................................................... 13
Chapter 5 Storage Sengs ........................................................................................................ 15
5.1 Set Downloading Time and Select Storage Disk for Alarm-Related Videos .......................... 15
Hik IP Receiver Pro User Manual
ii
5.2 Set Recording Server for Second Video Vericaon ............................................................ 16
Chapter 6 Automaon Output Management ............................................................................ 17
6.1 Congure Protocol Parameters ............................................................................................ 17
6.2 Check Event Monitor Logs ................................................................................................... 20
6.3 Add CID Events for Transcoding ........................................................................................... 21
6.4 Edit Encoding Device Event and Device Online/Oine Event .............................................. 21
Hik IP Receiver Pro User Manual
iii
Chapter 1 Overview
1.1 Introducon
As a protocol converter, the Hik IP Receiver Pro connects devices and ARC (alarm receiving center)
for data transmission, through LAN or WAN.
You can add devices (including AX Pro security control panel, network camera, NVR, and DVR)
managed on the Hik-ProConnect to the Hik IP Receiver Pro to integrate them to the ARC through
Sur-Gard protocol, Ademco 685 protocol, Manitou protocol, or SBN protocol. Aer correct
conguraons on the Hik IP Receiver Pro and the ARC, the Hik IP Receiver Pro can receive and
transmit alarms and alarm-related videos from devices on the Hik IP Receiver Pro to the ARC for
nocaon and video vericaon.
This manual guides you to congure the Hik IP Receiver Pro. To ensure a proper usage and stability
of the Hik IP Receiver Pro, refer to the contents below and read the manual carefully before
installaon and operaon.
1.2 Running Environment
The following is recommended system requirement for running the Hik IP Receiver Pro.
Operang System
Microso Windows 10 (64-bit) / Windows Server 2012 R2 (64-bit) / Windows Server 2016 (64-
bit)
Note
For Windows Server 2012 R2 (64-bit), the patch KB2999226 is required to be installed.
CPU
Intel Core i5-7500 @ 3.0 GHz, four-core or above
RAM
8 GB or above
NIC
Gigabit-NIC with latest driver
Hik IP Receiver Pro User Manual
1
Chapter 2 Installaon
You can install the Hik IP Receiver Pro service to your server or PC, and acvate the service. Then
you can use the service remotely.
2.1 Port Instrucon
Before installing Hik IP Receiver Pro service, ensure the default ports of the Hik IP Receiver Pro are
not used by other services, otherwise the Hik IP Receiver Pro service will be unavailable.
Plaorm Ports
• 80 (TCP) : HTTP port
• 443 (TCP) : HTTPS port
Device Ports
You can edit the device ports if they are conicted with the other ports on your PC.
Port Number Protocol Port Descripon
7661 TCP Used for registering devices to the Hik IP Receiver Pro by
ISUP5.0 protocol.
7662 TCP Used for sending alarms from ISUP5.0 security control
devices to the Hik IP Receiver Pro.
7091 TCP Used for sending picture and video data from ISUP5.0
security control devices to the Hik IP Receiver Pro.
Note
Scan the QR code below to get more details.
Hik IP Receiver Pro User Manual
2
2.2 Install Hik IP Receiver Pro
You can install the Hik IP Receiver Pro service on a computer or server. Aer that, you can start the
service, stop the service or exit the service by watchdog.
Steps
1. Right-click the program le and run as the administrator to enter the welcome panel of the
InstallShield Wizard.
2. Click Next to start the InstallShield Wizard.
3. Click Change... and select a proper directory as required to install the service.
4. Click Next to connue.
5. Oponal: Edit the HTTP port if the port number is conict, otherwise the installaon cannot be
connued.
6. Click Install to begin the installaon.
7. Read the post-install informaon and click Finish to complete the installaon.
Result
Aer successful installaon, the Watchdog service will get started and hide in the nocaon area
of the desktop. Right-click and select the opon to stop the service, start the service, or exist
the service.
Note
• If you install Hik IP Receiver Pro remotely, you need to log into the local computer to show the
Watchdog service.
• A window will pop up asking whether to keep the conguraon le when you re-install the Hik IP
Receiver Pro. You can choose to keep it or not.
2.3 Acvate Hik IP Receiver Pro
By default, Hik IP Receiver Pro predened the administrator user named admin. When you log in to
Hik IP Receiver Pro for the rst me, you are required to create a password for the admin user to
acvate Hik IP Receiver Pro before you can properly congure and operate it.
Before You Start
Make sure you have installed the Hik IP Receiver Pro service.
Steps
1. Enter the address of the computer or server running with Hik IP Receiver Pro service and port
number in the address bar of the web browser, and press Enter key.
Note
The default port is 80. For conguring the port number, see Edit Port for details.
Hik IP Receiver Pro User Manual
3
Example
If the IP address of the computer running Hik IP Receiver Pro service is 172.6.21.96, and the
port number is 80, and you should enter hp://172.6.21.96:80 in the address bar.
2. Enter the password and conrm password for the admin user in the pop-up Acvate Hik IP
Receiver Pro window.
Note
We highly recommend you change the password of your own choosing (using a minimum of 8
characters, including at least three kinds of following categories: upper case leers, lower case
leers, numbers, and special characters) in order to increase the security of your product.
3. Click Acvate.
The Hik IP Receiver Pro is acvated. And a nocaon for conguring Hik-ProConnect account
prompts.
4. Click Congure to enter the Hik-ProConnect Conguraon page, and congure Hik-ProConnect
parameters.
Note
If you want to congure the Hik-ProConnect parameters later, click Cancel. You can go to the
Hik-ProConnect Conguraon page to congure the parameters aer logging into the Hik IP
Receiver Pro. See Access Hik-ProConnect .
Hik IP Receiver Pro User Manual
4
Chapter 3 Device Management
The Hik IP Receiver Pro can manage mulple device types, e.g. network camera, DVR, NVR, and AX
Pro security control panel. Aer adding devices to the Hik IP Receiver Pro and conguring alarm
service and zone, the Hik IP Receiver Pro can transmit alarms and videos from these devices to
ARC.
Add Device
You can add Hikvision devices managed in the Hik-ProConnect to the Hik IP Receiver Pro, or add
one or more third-party devices to the Hik IP Receiver Pro.
Enable Receiving Alarm and Set Zone
Aer adding devices to the Hik IP Receiver Pro, you can enable alarm service and add zone for
these devices, and then link channels to zones to transmit videos from linked channels to ARC.
3.1 Add Hikvision Device(s) Managed in Hik-ProConnect
You can add Hikvision devices managed on Hik-ProConnect to the Hik IP Receiver Pro. Aer adding
the devices to Hik IP Receiver Pro, the Hik IP Receiver Pro can transmit alarms triggered by these
devices to ARC.
Before You Start
Make sure you have accessed the Hik IP Receiver Pro to Hik-ProConnect. See Access Hik-
ProConnect for details.
Steps
Note
This funcon should be supported by device. Devices including AX Pro security control panel, NVR,
DVR, and network camera support this funcon.
1. On the Device page, click Add to enter the Add Device page.
2. Check Hik Device as the Device Type.
Devices managed on Hik-ProConnect are displayed in the Choose Device eld.
3. Check devices and click Next.
4. Enter account ID.
Note
The account ID should contain only 4 digits, and should be the same with the account ID
congured on ARC.
5. Check to-be-added devices and click OK.
Hik IP Receiver Pro User Manual
5
The added devices are displayed on the Device page.
6. Oponal: Perform the following operaons if necessary.
Edit Device Click to edit device's account ID.
Delete Device Click to delete a device; or check mulple devices and click
Delete to delete the checked devices.
Enable Alarm Service
and Set Zone
See Enable Alarm Service and Set Zone for details.
3.2 Add Single Third-Party Device
You can add a third-party device to the Hik IP Receiver Pro by entering device account ID and
device name.
Steps
1. On the Device page, click Add to enter the Add Device page.
2. Check Third-Party Device as the Device Type.
3. Select Single Adding as the Adding Mode.
4. Enter account ID and device name.
Note
The account ID should contain only 4 digits, and should be the same with the account ID
congured on ARC.
5. Click OK.
6. Oponal: Perform the following operaons if necessary.
Edit Device Click to edit device's account ID and device name.
Delete Device Click to delete a device; or check mulple devices and click
Delete to delete the selected devices.
Enable Alarm Service
and Set Zone
See Enable Alarm Service and Set Zone for details.
3.3 Add Third-Party Devices in a Batch
When there are mulple third-party devices to add, you can enter the device informaon in a
predened template and then import it to the Hik IP Receiver Pro to add them in a batch.
Steps
1. On the Device page, click Add to enter the Add Device page.
2. Check Third-Party Device as the Device Type.
3. Select Batch Import as the Adding Mode.
4. Click Export and save the predened template (CSV le) on your PC.
Hik IP Receiver Pro User Manual
6
Andere Handbücher für Hik IP Receiver Pro
2
Inhaltsverzeichnis
Andere HIK VISION Empfänger Handbücher
