HIK VISION A15 Bedienungsanleitung
1
Camera
A15 and A35 Bullet Camera
Quick Start Guide
Network Bullet Camera·Quick Operation Guide
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual applies to the following models.
Model
A15
A35
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.
0501001031101
Network Bullet Camera·Quick Operation Guide
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
Network Bullet Camera·Quick Operation Guide
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info
Network Bullet Camera·Quick Operation Guide
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions:
Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
● In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
Network Bullet Camera·Quick Operation Guide
5
● Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.
Network Bullet Camera·Quick Operation Guide
6
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-30℃~+60℃,or -40°C ~ 60°C if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
operating environment.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
● Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)
Network Bullet Camera·Quick Operation Guide
7
Table of Contents
1 Appearance Description ................................................................. 8
2 Installation ...................................................................................... 9
3 Setting the Network Camera over the LAN .................................. 13
4 Accessing via Web Browser ................ Error! Bookmark not defined.
Network Bullet Camera·Quick Operation Guide
8
1 Appearance Description
Figure 1-1
Bullet Camera
Overview
Table 1-1 Description
No. Description
1 Sun Shield
2 Back Box
3 Grounding Screw
4 Adjustable Bracket
5 Mounting Base
6 Reset
1
2
3
4
5
6
Network Bullet Camera·Quick Operation Guide
9
2 Installation
Before you start:
Make sure the device in the package is in good condition and all
the assembly parts are included.
Make sure all the related equipment is power-off during the
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required
voltage to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three times
the weight of the camera.
For the camera that supports IR, you are required to pay attention to
the following precautions to prevent IR reflection:
● Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is finished. If there is dust or grease on the dome cover, clean
the dome cover with clean soft cloth and isopropyl alcohol.
Dieses Handbuch passt für folgende Modelle
1
Andere HIK VISION Sicherheitskamera Handbücher
HIK VISION
HIK VISION DS-2DT6232X-AELY Bedienungsanleitung
HIK VISION
HIK VISION DS-2CE12UF3T-E Bedienungsanleitung
HIK VISION
HIK VISION ECI-D64Z2 Bedienungsanleitung
HIK VISION
HIK VISION ECI-B14F2 Bedienungsanleitung
HIK VISION
HIK VISION DS-2TD2167-7/PI Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD7133-E Bedienungsanleitung
HIK VISION
HIK VISION DC-2CD20 Series Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD7126G0-IZS-B Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD783F-EI Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD4312F-I Benutzerhandbuch
HIK VISION
HIK VISION DS-2CD2D21G0/M-D/NF Bedienungsanleitung
HIK VISION
HIK VISION E-series Bedienungsanleitung
HIK VISION
HIK VISION TURBO HD H1T Series Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD5A46GO-IZS Bedienungsanleitung
HIK VISION
HIK VISION DS-2TD2137-4/P Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD3B46G2T-IZHS Bedienungsanleitung
HIK VISION
HIK VISION DS-2DF1-512 Bedienungsanleitung
HIK VISION
HIK VISION DS-2DP1618ZIXS-DE Bedienungsanleitung
HIK VISION
HIK VISION DS-2CE11D0T-PIRL Bedienungsanleitung
HIK VISION
HIK VISION DS-2CC512 P(N)-FB Bedienungsanleitung
