HIK VISION DS-2CC102P Bedienungsanleitung

User Manual of Color Camera

Version 2.1

Thank you for purchasing our product. If there is any question or request, please do not feel hesitated to

This manual may contain several technically incorrect places or printing errors, and the content is subject

to change without notice. The updates will be added into the new version of this manual. We will readily

improve or update the products or procedures described in the manual.

Security Awareness

This manual contains several guidelines for all customers’ demand. Please read it carefully before

operating to ensure that you can use this product correctly and safely，and to avoid the danger or material

damage which may cause otherwise. Please preserve it well for future reference.

The precaution measure is divided into “Warnings” and “Cautions” as below:

Warnings: Serious injury or death may cause if any of the warnings is neglected.

Cautions: Injury or equipment damage may cause if any of the cautions is neglected.

Warnings Follow these safeguards to

prevent serious injury or death.

Cautions Follow these precautions to

prevent potential injury or material

damage.

Warnings：

1. Input voltage should meet both the SELV(Safety Extra Low Voltage) and the Limited Power Source

with AC 24V or DC 12V according to the IEC60950－1 standard. Please refer to technical

specifications for detail information.

2. If the product does not work properly, please contact your dealer or the nearest service center. Never

attempt to disassemble the camera yourself. Users are responsible for any problem caused by

modifying or repairing without authorization.

3. The operating environment shall be away from rain or moisture to lower the danger of fire or shock

hazard.

4. The camera should be installed by qualified technicians, and comply with local laws and regulations.

5. Precautions for short circuit are required for installing.

6. Instructions for installation on walls: Please make sure that the camera can endure at least 50 Newton

(N)’s pulling downward.

Cautions：

1. Make sure the power supply voltage is correct before using the camera.

2. Do not drop the camera or subject it to physical shock.

3. Do not touch CCD (Charge Coupled Device) modules with fingers. If cleaning is necessary, use clean

cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period,

please turn on the lens cap to protect the CCD from dirt.

4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise

(which is not a malfunction however), and affecting the endurance of CCD at the same time.

5. The CCD may be burned out by a laser beam, so when any laser equipment is on using, make sure

that the surface of CCD will not be exposed to the laser beam.

6. Do not place the camera in extremely hot, cold(the operating temperature shall be－10℃～＋60℃),

dusty or damp locations, and do not expose it to high electromagnetism radiation.

7. To avoid heat accumulation, good ventilation is required for operating environment.

8. Keep the camera away from liquid while on using.

9. While on a delivery, the camera shall be packed in its original packing, or packing of the same

texture.

10. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced

regularly according to their average enduring time. The average time varies because of differences

between operating environment and using history, so regular checking is recommended for all the

users. Please contact with your dealer for more details.

Index

Chapter 1 Brief Introduction............................................................................................................................................5

1.1 Introduction.......................................................................................................................................................5

1.2 Introduction to the CameraAppearance............................................................................................................5

1.3 Side Elevation of the Camera............................................................................................................................6

1.4 Introduction to the Rear Panel of the Camera...................................................................................................7

Chapter 2 Installation............................................................................................................................................................9

2.1 Rear Panel..........................................................................................................................................................9

2.2 Power Supply.....................................................................................................................................................9

Chapter 3 Specification.......................................................................................................................................................10

Table 1.........................................................................................................................................................................10

Table 2.........................................................................................................................................................................11

Table 3.........................................................................................................................................................................12

Table 4.........................................................................................................................................................................13

Table 5.........................................................................................................................................................................14

Chapter 1 Brief Introduction

1.1 Introduction

This color camera with advanced circuit designing incorporates a CCD module that offers high sensitivity.

It is ideal for surveillance and video processing systems, and provides excellent performances such as

high resolution, low distortion and low noise, etc.

The camera incorporates extraordinary features as below: Compact Structure Design

1/3 Inch SONY CCD

Day / Night with Auto Switch

Auto White Balance, Auto Gain Control, Electronic Shutter Control, and Backlight Compensation

Flickerless Mode

Digital Signal Processing

Auto Iris with DC / Video Driver

CS Mount Lens (Provide OptionalAdapter for C Mount Lens)

Internal Synchronization

Advanced 3-axis mechanical design enables the camera to meet the installation requirement from

different environment by flexibly adjusting the lens into the require angle (Only DS-2CC511/591P-A

Support)

Advanced double board design enables heat dissipation and quality of the images

1.2 Introduction to the Camera Appearance

To open the dome cover, put one of your hands on the pedestal to stabilize it, and rotate the side cover in

anticlockwise direction with the other hand.

Dome cover

Core

Pedestal

Figure 1

Side Cover

1.3 Side Elevation of the Camera

Figure 2

Please pay attention to the connection mode for different drive iris lens plugs as Figure 2. The lens

interface is standard CS mount. The mark in the camera stands for day/night working.

[Notice] Different models may have different side elevations, please see the real.

1.4 Introduction to the Rear Panel of the Camera

Figure 3

①Level Adjusting：

Level adjusting is valid for iris adjusting in DC drive mode，while invalid for Video drive mode.

④Auto Iris Selecting：

Auto iris lens of both Video and DC drive modes can match this camera. Please select DD mode for

DC drive auto iris lens or VD mode for Video drive auto iris lens.

⑤SW Dial Switch Functions are listed as below.

Invalid. Designed for extended use.

NAGC

Normal AGC: Normal automatic gain control. The gain is about 30dB when

turned on.

SAGC

Super AGC：Super automatic gain control. The gain is about 60dB when

turned on.

MIRROR

The image will be reversed horizontally with this function on.

Use it to avoid the spot caused by different circuit power.

BLC

Back Light Compensation: Automatically adjust the exposure for back light

compensation.

Auto Iris：Turn the switch to AI for auto iris.

AES

Auto Electronic Shutter：Turn the switch to AES for non-auto-iris mode.

ECLIPS

Restrain the partly brightness to make other parts clear.

SHARP

To get sharper edges for images, turn on the SHARP function.

SOFT

To get softer edges for the image, turn on the SOFT function.

[Notice] Different models may have different rear panels, please see the real.

Chapter 2 Installation

Please check if all the items on the package list have been included with your camera and all the parts and

devices are of well function.

【Notice】The lens should be CS mount and its mass should be less than 1kg, and the prominent

part behind the mount surface should be less than 5mm.

【Notice】Please use a C mount adaptor for C mount lens.

2.1 Rear Panel

Connections for the rear panel：

Figure 4

2.2 Power Supply

Please make sure that the power supply matches the camera before you plug it into the equipment. The

usual charge is 12V DC or 24V AC. (For more detailed information about the types of power supply,

please refer to the technology specification for each referenced camera types.)

Chapter 3 Specification

Table 1

Model

Parameter

DS-2CC102P(N)(-A)

DS-2CC112P(N)(-A)

DS-2CC192P(N)(-A)

Image Sensor

1/3 inch SONY Super HAD CCD

Signal System

PAL / NTSC

Effective Pixels

PAL: 500 (H)×582 (V)

NTSC: 510 (H)×492 (V)

PAL: 752 (H)×582 (V)

NTSC: 768 (H) ×494 (V)

Min. Illumination

0.5Lux @ F1.2

Electronic Shutter

1/50 (1/60)s-1/100,000s

Day & Night

Electronic

Auto Iris Lens

DC / Video

Lens Mount

C / CS mount

Horizontal Resolution

420 TVL

480TVL

530TVL

Synchronization

Internal synchronization

Video Output

1Vpp Composite Output

S/N Ratio

More than 48 dB

BLC

ON / OFF

Working Temperature

-10℃--60℃

Power Supply

12VDC, ±10%, “-A” series support12VDC / 24V AC, ±10%.

Power Consumption

2W MAX ("-A" series 3.5MAX)

Dimension (mm)

63×59×114

Weight

550g

Notice: “-A” illustration of support AC24V±10% / DC12V±10% double power supply;

Dimension:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION Sicherheitskamera Handbücher

HIK VISION

HIK VISION TURBO HD DS-2CE56H0T-IT1F Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE12KF0T-FS Bedienungsanleitung

HIK VISION

HIK VISION DS?2CC1102P(N)(?A) Bedienungsanleitung

HIK VISION

HIK VISION Mini Dome Camera Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2AF1-7XY-B Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE11D0T-PIRL Bedienungsanleitung

HIK VISION

HIK VISION UD04285B Bedienungsanleitung

HIK VISION

HIK VISION DS-2AE7232TI-A Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD2636B-15/P Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE19U8T-IT3Z Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2345G0P-I Bedienungsanleitung

HIK VISION

HIK VISION Turbo HD D0T Series Bedienungsanleitung

HIK VISION

HIK VISION 64 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF5276 Series Bedienungsanleitung

HIK VISION

HIK VISION ECI-B12F Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE78U7T-IT1F Bedienungsanleitung

HIK VISION

HIK VISION DS-2CC1197P(N)-A(-C) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD7353F-EI Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE12KF0T-LFS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD4212F Benutzerhandbuch

HIK VISION

HIK VISION AP530HT Bedienungsanleitung

HIK VISION

HIK VISION THC-B227-LMS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD5A85G0-IZHS8 Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF1-57XY Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung