HIK VISION DS-2TD2117-6/V1 Bedienungsanleitung
COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd.
Quick Start Guide
Thermal Network Bullet Camera
[i]
Quick Start Guide
COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision. Unless otherwise stipulated, Hikvision does not make any
warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to Thermal Network Bullet Camera.
The Manual includes instructions for using and managing the
product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without
notice, due to firmware updates or other reasons. Please find the
latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and
logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
[ii]
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
[iii]
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for Class A device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
[iv]
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
[v]
Warnings
●Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-user.
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
[vi]
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
●The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.
●Do not place the camera in extremely hot, cold (the operating
temperature shall be between -40°C ~ 65°C), dusty or damp
locations, and do not expose it to high electromagnetic
radiation.
●To avoid heat accumulation, good ventilation is required for
operating environment.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
[vii]
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)
0505161090329
Table of Contents
1 Appearance Description ................................................................. 1
1.1 Type I Camera Appearance.............................................. 1
1.2 Type II Camera Appearance............................................. 2
1.3 Cable Description ............................................................ 3
2 Installation...................................................................................... 6
2.1 Memory Card Installation................................................ 7
2.1.1 Type I Camera Memory Card Installation.............. 7
2.1.2 Type II Camera Memory Card Installation............. 8
2.2 Wide Range Coverage for Different Specifications ........ 10
2.3 Installing Camera........................................................... 11
2.3.1 Installing Type I Camera...................................... 11
2.3.2 Installing Type II Camera..................................... 13
Installation of Network Cable Water-proof Jacket ......... 18
3 Setting the Network Camera over the LAN .................................. 21
3.1 Wiring ........................................................................... 21
3.2 Activating the Camera................................................... 22
3.2.1 Activation via Web Browser................................ 22
3.2.2 Activation via SADP Software ............................. 23
3.3 Modifying the IP Address .............................................. 25
4 Accessing via Web Browser .......................................................... 28
Appendix ......................................................................................... 31
Frequently Asked Questions (FAQ)...................................... 31
Device Running Error .................................................. 31
Device Upgrading........................................................ 31
Others ......................................................................... 31
Common Material Emissivity Reference.............................. 33
[1]
1Appearance Description
There are two kinds of thermal network bullet cameras: Type I bullet
camera, and Type II bullet camera. The appearance description of
two cameras are shown below.
1.1 Type I Camera Appearance
The overview of Type I thermal network bullet camera and its
components are shown below:
Type I Camera Overview
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere HIK VISION Sicherheitskamera Handbücher
HIK VISION
HIK VISION 26 series Bedienungsanleitung
HIK VISION
HIK VISION DS-2TD4166T-9 Bedienungsanleitung
HIK VISION
HIK VISION DS-2AF1-7**-B Bedienungsanleitung
HIK VISION
HIK VISION DS-2CV2G46G0-IDW Bedienungsanleitung
HIK VISION
HIK VISION DS-HD2 Bedienungsanleitung
HIK VISION
HIK VISION Network Speed Dome Camera Bedienungsanleitung
HIK VISION
HIK VISION DS-2XC6285G0-L Bedienungsanleitung
HIK VISION
HIK VISION TurboHD H0T Series Bedienungsanleitung
HIK VISION
HIK VISION HiWatch HWI-B140H-M Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD7133-E Bedienungsanleitung
HIK VISION
HIK VISION DS-2DE4225W-DE Bedienungsanleitung
HIK VISION
HIK VISION E-series Bedienungsanleitung
HIK VISION
HIK VISION DS-2DF1-574D Bedienungsanleitung
HIK VISION
HIK VISION DS-2AE4225TI-D Bedienungsanleitung
HIK VISION
HIK VISION UD.6L0201B1015A01 Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD2412F-I Bedienerhandbuch
HIK VISION
HIK VISION DS-2CC102PN-IRA Bedienungsanleitung
HIK VISION
HIK VISION THC-B129-P Bedienungsanleitung
HIK VISION
HIK VISION DS-2XM6222FWD-I Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD1021G0-I Bedienungsanleitung
