HIK VISION DS-3E1552P Series Bedienungsanleitung

PoE Switch

Quick Start Guide

PoE Switch Quick Start Guide

About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and

all other information hereinafter are for description and explanation only. The information

contained in the Manual is subject to change, without notice, due to firmware updates or other

reasons. Please find the latest version of this Manual at the Hikvision website ( https://

www.hikvision.com/ ).

Please use this Manual with the guidance and assistance of professionals trained in supporting the

Product.

Applicable Models

This manual is applicable to switches.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Danger

Indicates a hazardous situation which, if not avoided, will or could

result in death or serious injury.

Caution

Indicates a potentially hazardous situation which, if not avoided, could

result in equipment damage, data loss, performance degradation, or

unexpected results.

Note

Provides additional information to emphasize or supplement

important points of the main text.

•

PoE Switch Quick Start Guide

Chapter 1 Introduction

1.1

Product Introduction

DS-3E1552P series switches (hereinafter referred to as "the device") are layer 2 PoE switches,

providing advanced PoE power supply technology on the basis of high-performance access. The

switches support client management, network topology management, link aggregation, port

management and so on. The switches are suitable for small-scale LAN device access.

1.2

Packing List

Items

Quantity

Switch

× 1

Power Adapter

× 1

AC Power Cord

× 1

Screw

× 6

L-Shaped Bracket

× 1

Quick Start Guide

× 1

1.3

Appearance

Different models of devices may have different appearances. The following pictures are only for

illustration.

Front Panel

Figure 1-1 DS-3E1552P Series

PoE Switch Quick Start Guide

Rear Panel

Figure 1-2 DS-3E1552P Series

Port/Indicator Description

Indicator/Port

Description

PoE-MAX Indicator

•Solid /Flashing: The output power of the switch will reach the

upper limit. The power supply may be abnormal if more devices

are connected.

•Unlit: The switch provides power supply to PD normally.

PWR Indicator

•Solid: The switch is powered on normally.

•Unlit: No power supply connected or power supply is abnormal.

Indicator Switching Button

Press on it until LINK/ACT indicator lighting, which shows ports data

transmission status.

•Solid: The port is connected.

•Flashing: The port is transmitting data.

•Unlit: The port is disconnected or connection is abnormal.

Press on it until PoE indicator lighting, which shows port power

provide status.

•Solid: The switch provides power supply to PD normally.

•Unlit: The switch is disconnected to PD, or provides power supply

to PD abnormally.

Gigabit PoE RJ45 Port

Used for PD devices connection via network cables.

Gigabit RJ45 Port

Used for other devices connection via network cables.

Gigabit SFP Fiber Optical

Port

Used for optical module connection via optical fiber.

Grounding Terminal

Used for connecting to the grounding cable to protect the switch

from lightning.

Power Supply

Use the attached power cord to connect the switch to socket.

PoE Switch Quick Start Guide

Chapter 2 Installation

Please select the appropriate installation method according to the actual needs.

Before You Start

•Ensure that the desktop or rack is stable and firm enough.

•Keep the room well-ventilated. Keep at least 10 cm distance around the device for heat

dissipation.

•Keep at least 1.5 cm vertical distance between two adjacent devices for rack-mountinstallation.

2.1

Desk-Mounted Installation

Place the device on the desk.

2.2

Rack-Mounted Installation

Steps

1. Check the grounding and stability of the rack.

2. Use the attached screws to fix the two L-shaped brackets to the sides of theswitch.

Figure 2-1 Fix L-Shaped Brackets

3. Place your switch on the rack, fix it to the rack with self-prepared screws to stably install your

switch.

Figure 2-2 Fix to the Rack

PoE Switch Quick Start Guide

Chapter 3 Grounding

3.1 Connecting the Grounding Cable

Grounding is used to quickly release overvoltage and overcurrent induced by lightening for switch,

and to protect personal safety. Select the appropriate grounding method according to your needs.

3.1.1 With Grounding Bar

If a grounding bar is available at the installation site, follow the steps below.

Steps

1. Connect one end of the grounding cable to the binding post on the grounding bar.

2. Connect the other end of the grounding cable to the grounding terminal of the device and fix

the screw.

Figure 3-1 Grounding with Grounding Bar

3.1.2 Without Grounding Bar

If there is no grounding bar but the earth is nearby and the grounding body is allowed to be

buried, follow the steps below.

Steps

1. Bury an angle steel or steel pipe (≥ 0.5 m) into the mud land.

2. Weld one end of the grounding cable to the angle steel or steel pipe and embalm thewelding

point via electroplating or coating.

3. Connect the other end of the grounding cable to the grounding terminal.

PoE Switch Quick Start Guide

Figure 3-2 Grounding with Angle Steel

3.2 Connecting RJ45 Port

Use a network cable to connect the device to the RJ45 port of a peer device such as network

camera, NVR, switch, etc.

Figure 3-3 RJ45 Port Connection

PoE Switch Quick Start Guide

3.3 Connecting SFP Optical Module

Connecting SFP optical module is supported when the device has a fiber optic port or a combo.

When connected to a network cable, the combo is a RJ45 port. When plugged into with an optical

module and connected to an optical fiber, the combo functions as a fiber optic port.

When connected to both the network cable and optical fiber at the same time, the port works as a

fiber optic port.

Steps

•Single-Mode optical module needs to be paired.

•Do not bend fiber optic (curvature radius ≥ 10 cm) overly.

•Do not look directly at fiber optic connector because the laser is harmful to eyes.

Connect the two paired SFP optical modules with an optical fiber.

Hold the SFP optical module from one side, and smoothly plug it into the device along with the

SFP port slot until the optical module and the device are closely attached.

After powering on the device, check the status of LINK/ACT indicator. If the indicator is lit, the

link is connected. If the indicator is unlit, the link is disconnected. Check the line, and make sure

peer devices have been started.

Caution

PoE Switch Quick Start Guide

Chapter 4 Powering on the Device

Please use the attached power cord in package to power on the device.

Before powering your switch, make sure that:

•The operating power supply is compliant with rated input standard.

•Port cables and grounding cables are correctly connected.

•If there is outdoor cabling, connect a lightning rod and lightening arrester to thecable.

PoE power supply line and strong wire cannot be wired together, otherwise PD equipment or

switch ports will be burnt.

Caution

PoE Switch Quick Start Guide

Chapter 5 Device Management

The device can be configured and managed through iVMS-4200 software, mainly including network

parameter configuration, port configuration, link aggregation configuration, network topology

display and so on.

•This chapter will briefly introduce the device management through iVMS-4200 software. For

other functions, please refer to User Manual of iVMS-4200 Software.

•All pictures in this manual are for illustration only, and the specific interface is subject to the

actual interface.

5.1

Activating Devices

For the inactive devices, you are required to create a password to activate them before they can be

added to the software and work properly.

Before You Start

Make sure the device to be activated is connected to the network and is in the same subnet with

the PC running the client.

Step

1. Enter the Device Management page.

2. Click Device tab on the top of the right panel.

3. Click Online Device to show the online device area at the bottom of the page.

The searched online devices are displayed in the list.

4. Check the device status (shown on Security Level column) and select an inactivedevice.

Figure 5-1 Online Inactive Device

5. Click Activate to open the Activation dialog.

6. Create a password in the password field, and confirm the password.

Note

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION Schalten Handbücher

HIK VISION

HIK VISION DS-3E15 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1X05P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E0105P-E Bedienungsanleitung

HIK VISION

HIK VISION DS-3D2208P Handbuch

HIK VISION

HIK VISION DS-3E03 P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3TXX06HP-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1 P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1106HP-EI Bedienungsanleitung

HIK VISION

HIK VISION DS-3E13XXP-SI Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E2528B Bedienungsanleitung

HIK VISION

HIK VISION DS-3E2500-H Series Bedienungs- und Wartungshandbuch

HIK VISION

HIK VISION DS-3E0526P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1 P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1326P-EI Bedienungsanleitung

HIK VISION

HIK VISION 0500P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-KAD606-P Bedienungsanleitung

HIK VISION

HIK VISION DS-3E0318P-E Bedienungsanleitung

HIK VISION

HIK VISION DS-3E15 P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E2510P Bedienungsanleitung

HIK VISION

HIK VISION DS-3E1510P Bedienungsanleitung

HIK VISION

HIK VISION DS-3E2300P Series Bedienungsanleitung

HIK VISION

HIK VISION DS-3E0108P-E Bedienungsanleitung

HIK VISION

HIK VISION DS-3T1310P-SI/HS Bedienungsanleitung

HIK VISION

HIK VISION DS-3D2228P Montageanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung