Hilti PD 5 Bedienungsanleitung

PD 5

Operating instructions en

Mode d’emploi fr

Manual de instrucciones es

Manual de instruções pt

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

&/,&.











Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

PD 5 laser range meter

It is essential that the operating instructions

are read before the laser range meter is

used the first time.

Ensure that the operating instructions are

with the laser range meter when it is given

to other persons.

Parts, operating controls and indicators 

햲Laser emitting and receiving lens

햳On/off button

햴Measure button

햵Battery compartment cover

햶Graphic display

Contents Page

1. General information 1

2. Description 2

3. Accessories 3

4. Technical data 3

5. Safety instructions 4

6. Before use 6

7. Operation 7

8. Care and maintenance 8

9. Troubleshooting 10

10. Disposal 11

11. Manufacturer’s warranty - tools 11

12. FCC statement / IC statement 12

1. General information

1.1 Safety Notices and their meaning

-CAUTION-

This word indicates a possibly hazardous situation which

could result in slight bodily injuries or damage to property.

-NOTE-

This word indicates information to help the user employ the

product efficiently and other useful notes.

These numbers refer to the corresponding illustrations.

The illustrations can be found on the fold-out cover pages.

Keep these pages open while studying the operating instruc-

tions.

In these operating instructions, the designation “the tool”

always refers to the PD 5 laser range meter.

ORIGINAL OPERATING INSTRUCTIONS

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

2. Description

2.1 Intended use

The range meter is designed for the:

• Measurement of distances

2.2 Display

The measurements, settings and tool status are shown in

the display. When the tool is in measuring mode, the mea-

surements taken are shown at the bottom of the display

area (the result line).

2.3 Display illumination

In low light conditions, the display is illuminated automat-

ically as soon as a button is pressed. If no button is pressed

over a period of 20 seconds, the display illumination switches

off automatically.

1.2 Explanation of the pictograms and other

information

Read the

operating

instructions

before use.

Temperature

indicator

>1/4s

Do not look

into the beam.

Symbols

Laser class 2 Return waste

material for

recycling.

Battery status

indicator Hardware

errors Unfavorable

operating

conditions

Warning signs

General

warning

1.3 Location of identification data on the range meter

The type designation and serial number can be found on the

rating plate on the back side of the range meter. Make a note

of this data in your operating instructions and always refer

to it when making an enquiry to your Hilti representative or

service department.

Type:

Serial no.:

Laser class II according

to CFR 21, § 1040 (FDA)

CLASS II LASER PRODUCT

620-690nm/0.95mW max.

LASER RADIATION - DO NOT

STARE INTO BEAM

Symbols

KCC-REM-

HLT-PD5

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

Power supply

2×1.5 V, type AAA batteries

Battery condition check

Battery condition indicator with 4 segments showing

100%, 75%, 50%, 25% charge :

No segments shown: The batteries are exhausted

2.4 Basic principle

The distance is measured along a laser beam emitted by

the tool to the point at which the beam strikes a reflective

surface. The target from which the measurement is taken

is clearly identified by the red laser measuring spot. The

range of the tool depends on the reflectance and structure

of the target surface from which measurements are taken.

2.5 Control panel

2.6 Items supplied

1 PD 5 laser range meter

2 Batteries

1 Soft pouch

1 Operating instructions

1 Manufacturer’s certificate

On/off button When the tool is switched off, press

the button briefly to switch it on.

When the tool is switched off, press and

hold the button to activate the menu.

When the tool is switched on, press the

button briefly to switch it off.

Measure button Quick start (When the tool is switched

off: Press the button briefly - the tool

switches on and activates the laser).

Begins distance measurement.

Activates the laser beam.

Activates continuous measuring mode

(long press, approx. 2 sec.).

Stops continuous measuring mode.

3. Accessories

Not supplied with the tool.

Target plate PDA 50 with reflective coating

(4.7×5.1 in)

PDA 51 (4.7×5.1 in)

PDA 52 with reflective coating

(8.3×11.7 in)

Laser visibility glasses PUA 60

4. Technical data

Right of technical changes reserved.

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

5. Safety instructions

In addition to the information relevant to safety given in

each of the sections of these operating instructions, the

following points must be strictly observed at all times.

5.1 Basic information concerning safety

a) Do not render safety devices ineffective and do not

remove information and warning notices.

b) Keep laser tools out of reach of children.

c) Failure to follow the correct procedures when opening

the tool may cause emission of laser radiation in excess

of class 2. Have the tool repaired only at a Hilti ser-

vice center.

d) Modification of the tool is not permissible.

e) Check that the tool functions correctly each time before

use.

f) Measurements taken from surfaces with low reflectiv-

ity in highly reflective surroundings may be inaccurate.

g)Measurements taken through panes of glass or other

objects may be inaccurate.

Measuring range (with target plate)

10 in … 230 ft

Accuracy

Typically ±1/16 in for single and continuous

measurement **

** Atmospheric influences interfere with distance measurements. Over long

distances, an influence of ±1/16 in + 20 ppm of the measured distance is

to be expected. Typical accuracy: 2 Sigma at 77 °F.

Basic operating modes

Single measurement / Continuous measurement

Display

Illuminated liquid-crystal display showing distance,

operating and battery status

Laser class

Visible 635 nm, Output power less than 1 mW:

Laser class 2

EN 60825-1:2007; IEC 60825-1:2007 CFR 21 § 1040 (FDA)

Automatic cut-out

Laser: 1 min / Tool: 10 min

Battery life

Up to 5000 measurements at room temperature

Operating temperature range

+14 °F … +122 °F

Storage temperature

-22 °F … +158 °F

Protection class

IP 55 protection against dust and water jets IEC 60529

Weight with batteries

0.22 lb

Dimensions

6.5 ×1.3 ×0.8 in

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

h) Rapidly changing conditions, e.g. persons walking through

the path of the laser beam, falling snow, etc., may lead

to incorrect measurements.

i) Do not point the tool toward the sun or other powerful

light sources.

j) Take the influences of the surrounding area into account.

Do not use the tool where there is a risk of fire or explo-

sion.

5.2 Proper organization of the workplace

a) Avoid unfavorable body positions when working from

ladders. Make sure you work from a safe stance and

stay in balance at all times.

b) When the tool is brought into a warm environment from

very cold conditions, or vice-versa, allow it to become

acclimatized before use.

c) As a precaution, check the previous settings and adjust-

ments you have made.

d) Secure the area in which you are working and take

care to avoid directing the beam towards other per-

sons or towards yourself when setting up the tool.

e) Use the tool only within its specified limits.

f) Observe the accident prevention regulations applica-

ble in your country.

5.3 Electromagnetic compatibility

Although the tool complies with the strict requirements of

the applicable directives, Hilti cannot entirely rule out the

possibility of the tool being subject to interference caused

by powerful electromagnetic radiation, leading to incorrect

operation. Check the accuracy of the tool by taking mea-

surements by other means when working under such con-

ditions or if you are unsure. Likewise, Hilti cannot rule out

the possibility of interference with other devices (e.g. air-

craft navigation equipment). The tool complies with the

requirements of class A; The possibility of interference

occurring in a domestic environment cannot be excluded.

5.4 General safety rules

a) Check the condition of the tool before use. If the tool

is found to be damaged, have it repaired at a Hilti ser-

vice center.

b) The user must check the accuracy of the tool after it

has been dropped or subjected to other mechanical

stresses.

c) Although the tool is designed for the tough conditions

of jobsite use, as with other measuring instruments it

should be treated with care.

d) Although the tool is protected to prevent entry of damp-

ness, it should be wiped dry each time before being

put away in its transport container.

5.5 Electrical

a) Keep the batteries out of reach of children.

b) Do not allow the batteries to overheat and do not expose

them to fire. The batteries may explode or release toxic

substances.

c) Do not charge the batteries.

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

6. Before use

6.1 Inserting the batteries

CAUTION

Do not use damaged batteries.

CAUTION

Always replace the complete set of batteries.

DANGER

Do not mix old and new batteries. Do not mix batteries

of different makes or types.

1. Open the battery compartment.

2. Remove the batteries from the packaging and insert them

in the tool.

NOTE Check to ensure correct battery polarity (refer to

the markings on the underside of the tool).

3. Close the battery compartment cover.

4. Check to ensure that the battery compartment cover is

closed securely.

6.2 Switching the tool on / off

1. The tool can be switched on by pressing either the “On

/ off” button or the “Measure” button.

2. When the tool is switched off, press the “On / off” but-

ton: The tool switches on.

The laser beam is switched off.

d) Do not solder the batteries into the tool.

e) Do not discharge the batteries by shortcircuiting. This

may cause them to overheat and present a risk of per-

sonal injury (burns).

f) Do not attempt to open the batteries and do not sub-

ject them to excessive mechanical stress.

g) Do not use carbon-zinc batteries in the tool.

5.6 Laser classification

Depending on the version purchased, the tool complies

with Laser Class 2 in accordance with IEC825-1:2007 /

EN60825-1:2007 and Class II in accordance with CFR 21

§ 1040 (FDA). This tool may be used without need for fur-

ther protective measures. The eyelid closure reflex pro-

tects the eyes when a person looks into the beam unin-

tentionally for a brief moment. This eyelid closure reflex,

however, may be negatively affected by medicines, alco-

hol or drugs. Nevertheless, as with the sun, one should not

look directly into sources of bright light. Do not direct the

laser beam toward persons.

5.7 Transport

Always remove the batteries before shipping the tool.

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

3. When the tool is switched on, press the “On / off” but-

ton: The tool switches off.

4. When the tool is switched off, press the “Measure” but-

ton: The tool and the laser beam switch on.

6.3 First distance measurements

1. Press the “Measure” button once.

If switched off, the tool will be switched on and the laser

beam activated.

If the tool is already switched on, the laser beam will be

activated.

2. Aim the tool by positioning the visible laser spot on a

white surface at a distance of approx. 10-30 ft.

3. Press the “Measure” button again.

The distance will be displayed in less than a second, e.g.

17.99 ft.

You have just taken your first measurement with the tool.

6.4 Settings menu

1. With the tool switched off, press the “On / off” button

for approx. 2 seconds to enter menu mode.

2. Press the "Measure" button to switch the beep signal on

or off.

3. Press the "On / off" button to access the measuring units

settings.

4. Press the "Measure" button repeatedly to scroll through

the choice of units.

5. To close the menu, press and hold the "On / off" button

for approx. 2 seconds.

The tool is switched off and all the settings shown will be

saved.

6.5 Measuring references

All measurements taken with the PD 5 have the bottom end

of the tool as the default reference setting.

6.6 Measuring distances

Distances can be measured from all stationary targets with-

out a highly reflective surface, i.e. concrete, stone, wood,

plastic, paper, etc. The use of prisms or other highly reflec-

tive targets is not permissible and, if attempted, may fal-

sify the results.

7. Operation

7.1 Distance measurements

NOTE

With all functions of the tool, each step in the operation is

always indicated in the display.

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

8. Care and maintenance

8.1 Cleaning and drying

1. Blow dust off the lens.

2. Do not touch the lens with the fingers.

3. Use only a clean, soft cloth for cleaning. If necessary,

moisten the cloth slightly with pure alcohol or a little water.

NOTE Do not use any other liquids as these may damage

the plastic components.

4. The temperature limits for storage of your equipment must

be observed, especially in winter / summer.

8.2 Storage

Remove the tool from its case if it has become wet. The tool,

its carrying case and accessories should be cleaned and

dried (at maximum 104 °F). Repack the equipment only once

it is completely dry.

Check the accuracy of the equipment before it is used after

a long period of storage or transportation.

Remove the batteries from the tool before storing it for a

long period. Leaking batteries may damage the tool.

8.3 Transport

Use the original packaging or packaging of equivalent qual-

ity for transporting or shipping your equipment.

CAUTION

Always remove the batteries before shipping the tool.

NOTE

If measuring errors occur during continuous measuring,

and continuous measuring mode is canceled by pressing

the “Measure” button again, the last valid measurement will

be displayed.

7.2 Single distance measurement

1. Switch on the laser beam by pressing the “Measure” key.

2. Press the “Measure” key once again. Generally, the mea-

sured distance will be completed in less than a second

and shown in the result line on the display.

7.3 Continuous measurement

Press the “Measure” key for 2 seconds to activate this mea-

suring mode.

When doing so, it does not matter whether or not the range

meter is off or the laser beam is switched on or off. The range

meter will always switch to continuous measurement.

During continuous measurement, the distances are updated

in the result line by about 8 to 15 measurements every sec-

ond. This depends on the reflectivity of the target surface.

Continuous measurement is indicated by a beep. The mea-

suring process is stopped by pressing the "Measure" key

once again. On doing so, the last valid distance measure-

ment shows in the result line on the display.

Printed: 07.07.2013 | Doc-Nr: PUB / 5145343 / 000 / 00

Andere Handbücher für PD 5

Inhaltsverzeichnis

Andere Hilti Laser-Nivelliergerät Handbücher

Hilti

Hilti PRI 36 Bedienungsanleitung

Hilti

Hilti PR 30-HVS A12 Bedienungsanleitung

Hilti

Hilti POT 10 Bedienungsanleitung

Hilti

Hilti PR 30-HVSG Bedienungsanleitung

Hilti

Hilti PML 42 Bedienungsanleitung

Hilti

Hilti PR 2-HS A12 Bedienungsanleitung

Hilti

Hilti PR 3 Bedienungsanleitung

Hilti

Hilti PM 30-MG Bedienungsanleitung

Hilti

Hilti PMD 200 Bedienungsanleitung

Hilti

Hilti PRI 2 Bedienungsanleitung

Hilti

Hilti PM 40-MG Bedienungsanleitung

Hilti

Hilti PR 2-HS Bedienungsanleitung

Hilti

Hilti PR 3-HVSG Bedienungsanleitung

Hilti

Hilti PRA 20G Bedienungsanleitung

Hilti

Hilti PML 32 Bedienungsanleitung

Hilti

Hilti PRE 38 Bedienungsanleitung

Hilti

Hilti PR 30-HVSG A12 Bedienungsanleitung

Hilti

Hilti PML 42 Bedienungsanleitung

Hilti

Hilti PM 2-PG Bedienungsanleitung

Hilti

Hilti PRI 36 Bedienungsanleitung

Hilti

Hilti PR 25 Bedienungsanleitung

Hilti

Hilti PD-S Bedienungsanleitung

Hilti

Hilti PR 2-HS A12 Bedienungsanleitung

Hilti

Hilti PMP 34-F Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung