Hioki 3664 Bedienungsanleitung

OPTICAL POWER METER

INSTRUCTION MANUAL

3664

www. .com information@itm.com1.800.561.8187

Contents

APP

IDX

Contents

Introduction .................................................................. 1

Inspection ..................................................................... 1

Safety Information ........................................................ 2

Operating Precautions ................................................. 4

1Overview 7

1.1 Product Overview ............................................... 7

1.2 Features ............................................................. 8

1.3 Names and Functions of Parts ...........................9

2 Measurement Preparations 13

2.1 Attaching the Strap ...........................................13

2.2 Supplying Power .............................................. 14

2.2.1 Using the AC Adapter ........................................14

2.2.2 Using the Batteries ............................................15

2.3 Connecting the Optical Sensor .........................16

2.4 Connecting the Analog Output Cord ................17

2.5 Turning the Power On and Off .........................18

3 Measurement 19

3.1 Setting the Measurement Mode .......................20

3.2 Setting the Range .............................................21

3.2.1 Auto Range .......................................................21

3.2.2 Manual Range ...................................................22

3.3 Setting the Wavelength .................................... 24

3.3.1 Setting an Arbitrary Measurement Wavelength .24

3.3.2 Retrieving the Wavelength Setting from the

Measurement-Wavelength Memory ..................26

3.4 Starting Measurement ......................................26

3.5 Setting Example ............................................... 28

3.5.1 Optical-Power Measurement .............................28

3.5.2 Relative Measurement (Measured-value basis) 29

3.5.3 Relative Measurement (Input-value basis) ........31

www. .com information@itm.com1.800.561.8187

Contents

4 Functions 33

4.1 Scalling Function .............................................. 33

4.1.1 Turning ON the Scaling Function ......................33

4.1.2 Turning OFF the Scaling Function .....................36

4.2 Maximum-Value Hold / Minimum-Value Hold

/ Averaging ....................................................... 37

5 Control by Computer 39

5.1 Overview of Control .......................................... 40

5.2 Installing the Driver ...........................................41

6 Specifications 51

6.1 Measurement Specifications ............................51

6.2 General Specifications .....................................53

7 Maintenance and Service 55

7.1 Cleaning ...........................................................55

7.1.1 Cleaning of the 3664 .........................................55

7.1.2 Cleaning of the Optical Sensors ........................56

7.2 Service ............................................................. 56

7.3 Error Display .....................................................57

7.4 Reset ................................................................59

7.4.1 System Reset ....................................................59

7.4.2 Setting Data Reset ............................................59

7.4.3 Measurement-Wavelength Memory Reset ........60

7.5 Replacing the Batteries .................................... 61

Appendix 63

Explanations ..............................................................63

Options .......................................................................64

www. .com information@itm.com1.800.561.8187

Introduction

Thank you for purchasing the HIOKI “Model 3664 OPTICAL

POWER METER.” To obtain maximum performance from the

instrument, please read this manual first, and keep it handy for

future reference.

Registered Trademarks:

• Windows is a registered trademark of Microsoft Corporation in

the United States and/or other countries.

• Adobe, the Adobe logo, Acrobat, the Acrobat logo are trade-

marks of Adobe Systems Incorporated.

Inspection

• When you receive the instrument, inspect it carefully to ensure

that no damage occurred during shipping. In particular, check the

accessories, panel switches, and connectors. If damage is evi-

dent, or if it fails to operate according to the specifications, con-

tact your dealer or Hioki representative.

• Use the original packing materials when transporting the instru-

ment, if possible.

Verifying Package Contents

Options Model 9246 CARRYING CASE....................................................1

Model 9742 OPTICAL SENSOR..................................................1

Model 9742-10 OPTICAL SENSOR.............................................1

Model 3664 OPTICAL

POWER METER (1)

Model 9445-02 AC ADAPTER or

Model 9445-03 AC ADAPTER (1) Model 9094 OUTPUT CORD (1)

Instruction Manual (1)

LR6 alkaline batteries (4)

Driver CD-R (1)

USB Cable (1)

Strap (1)

www. .com information@itm.com1.800.561.8187

Safety Information

Safety Symbols

This manual contains information and warnings essential for safe

operation of the instrument and for maintaining it in safe operating

condition. Before using it, be sure to carefully read the following

safety precautions.

The following symbols in this manual indicate the relative impor-

tance of cautions and warnings.

Other Symbols

This instrument is designed to comply with IEC 61010 Safety

Standards, and has been thoroughly tested for safety prior

to shipment. However, mishandling during use could result

in injury or death, as well as damage to the instrument. Be

certain that you understand the instructions and precautions

in the manual before use. We disclaim any responsibility for

accidents or injuries not resulting directly from instrument

defects.

In the manual, the symbol indicates particularly

important information that the user should read before

using the instrument.

The symbol printed on the instrument indicates that

the user should refer to a corresponding topic in the

manual (marked with the symbol) before using the

relevant function.

Indicates that incorrect operation presents an

extreme hazard that could result in serious injury or

death to the user.

Indicates that incorrect operation presents a signifi-

cant hazard that could result in serious injury or

death to the user.

Indicates that incorrect operation presents a possi-

bility of injury to the user or damage to the instru-

ment.

Indicates advisory items related to performance or

correct operation of the instrument.

Indicates the prohibited action.

❖Indicates the location of reference information.

www. .com information@itm.com1.800.561.8187

Overvoltage Categories (CAT)

To ensure safe operation of measurement instruments, IEC 60664

establishes safety standards for various electrical environments,

categorized as CAT I to CAT IV, and called overvoltage categories.

These are defined as follows.

Higher-numbered categories correspond to electrical environments

with greater momentary energy. So a measurement device

designed for CAT III environments can endure greater momentary

energy than a device designed for CAT II.

Using a measurement instrument in an environment designated

with a higher-numbered category than that for which the instrument

is rated could result in a severe accident, and must be carefully

avoided.

CAT I Secondary electrical circuits connected to an AC

electrical outlet through a transformer or similar

device.

CAT II Primary electrical circuits in equipment connected to

an AC electrical outlet by a power cord (portable

tools, household appliances, etc.)

CAT III Primary electrical circuits of heavy equipment (fixed

installations) connected directly to the distribution

panel, and feeders from the distribution panel to out-

lets.

CAT IV The circuit from the service drop to the service

entrance, and to the power meter and primary over-

current protection device (distribution panel).

www. .com information@itm.com1.800.561.8187

Operating Precautions

Follow these precautions to ensure safe operation and to obtain

the full benefits of the various functions.

Observe the following to avoid damage to the instrument.

• Do not allow the instrument to get wet, and do not take measure-

ments with wet hands. This may cause an electric shock.

• Do not use the instrument where it may be exposed to corrosive

or combustible gases. The instrument may be damaged or

cause an explosion.

• To avoid damage to the instrument, protect it from physical

shock when transporting and handling. Be especially careful to

avoid physical shock from dropping.

• Do not store or use the instrument where it could be exposed to

direct sunlight, high temperature or humidity, or condensation.

Under such conditions, the instrument may be damaged and

insulation may deteriorate so that it no longer meets specifica-

tions.

• This instrument is designed for use indoors. It can be operated

at temperatures between 0 and 40°C without degrading safety.

Direct

Avoid the following

Sunlight

High Temperature

High Humidity

• After use, always turn OFF the power.

• The “ ” indicator appears when battery voltage becomes low.

Replace the batteries as soon as possible.

• Use the specified battery (AA alkaline battery) only. If a non-

specified battery such as a manganese battery is used, the

service hours may be shortened.

• When connecting the instrument to a PC with a USB cable,

use a cable of 2 m or shorter to prevent the influence of noise.

www. .com information@itm.com1.800.561.8187

Cords and Cables

• Avoid stepping on or pinching cables, which could damage the

cable insulation.

• To avoid breaking the cables, do not bend or pull them.

• To avoid damaging the output cable, grasp the connector, not

the cable, when unplugging the cable.

Optical Sensor

• Use only the specified optical sensor. Using a non-specified sen-

sor may result in incorrect measurements due to poor connec-

tion or other reasons.

• To prevent damage to the instrument and sensor, never connect

or disconnect a sensor while the power is on, or while the sensor

is connected around a conductor.

• To avoid damaging the optical sensor and to ensure accurate

measurements, avoid dropping or applying any physical shock

to the optical sensor.

• Avoid touching the detector window with your bare hands. The

detector window must be clean for the sensor to meet the speci-

fied performance parameters.

• Avoid scratching the detector window with sharp or pointed

objects (e.g., the tips of tweezers) or against hard surfaces.

Damage to the detector window may prevent the sensor from

meeting specified performance parameters.

• Make sure no stress is applied to the repeater cable of the 9742-

10 between the sensor main unit and its detector element.

To prevent dust accumulation, stains, and damage, cover the

detector window with the sensor cover when the sensor is not in

use.

www. .com information@itm.com1.800.561.8187

Preliminary Checks

• Before using the instrument, make sure that the insulation on the

optical sensor cable and USB cable is undamaged and that no

bare conductors are improperly exposed. Using the instrument

in such conditions could cause an electric shock, so contact your

dealer or Hioki representative for repair.

• Before using the instrument the first time, verify that it operates

normally to ensure that the no damage occurred during storage

or shipping. If you find any damage, contact your dealer or Hioki

representative.

Care and Handling of CD-R

• Always hold the disc by the edges, so as not to make finger-

prints on the disc or scratch the printing.

• Never touch the recorded side of the disc. Do not place the disc

directly on anything hard.

• Do not wet the disc with volatile alcohol or water, as there is a

possibility of the label printing disappearing.

• To write on the disc label surface, use a spirit-based felt pen. Do

not use a ball-point pen or hard-tipped pen, because there is a

danger of scratching the surface and corrupting the data. Do not

use adhesive labels.

• Do not expose the disc directly to the sun's rays, or keep it in

conditions of high temperature or humidity, as there is a danger

of warping, with consequent loss of data.

• To remove dirt, dust, or fingerprints from the disc, wipe with a dry

cloth, or use a CD cleaner. Always wipe radially from the inside

to the outside, and do no wipe with circular movements. Never

use abrasives or solvent cleaners.

• Hioki shall not be held liable for any problems with a computer

system that arises from the use of this CD-R, or for any problem

related to the purchase of a Hioki product.

www. .com information@itm.com1.800.561.8187

1.1 Product Overview 7

The 3664 OPTICAL POWER METER is an instrument for measur-

ing the optical power of a spatial light. It is suitable for measure-

ment of the optical power of a laser light source and an LED light

source. The 3664 is a hand-held meter equipped with various mea-

surement functions and interfaces that meet diversified measure-

ment needs. The optical sensors (optional) for the power meter are

interchangeable, as the sensitivity of each sensor is adjusted inde-

pendently.

Overview 1

1.1 Product Overview

www. .com information@itm.com1.800.561.8187

Andere Handbücher für 3664

Inhaltsverzeichnis

Andere Hioki Messgerät Handbücher

Hioki

Hioki IM3536 Bedienungsanleitung

Hioki

Hioki 3284 HiTester Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Hioki

Hioki FT6380 Bedienungsanleitung

Hioki

Hioki 8715-01 Bedienungsanleitung

Hioki

Hioki CM4001 Bedienungsanleitung

Hioki

Hioki 3196 Bedienungsanleitung

Hioki

Hioki 3143 Bedienungsanleitung

Hioki

Hioki BT4560 Bedienungsanleitung

Hioki

Hioki SM-8216 Bedienungsanleitung

Hioki

Hioki RM9010-01 Bedienungsanleitung

Hioki

Hioki IM3533-01 Gebrauchs- und Pflegehandbuch

Hioki

Hioki MR8880-20 Bedienungsanleitung

Hioki

Hioki Memory HiCorder MR6000 Bedienungsanleitung

Hioki

Hioki LR8400-92 Bedienungsanleitung

Hioki

Hioki 3283-20 Bedienungsanleitung

Hioki

Hioki 8730-10 Bedienungsanleitung

Hioki

Hioki 3270 Bedienungsanleitung

Hioki

Hioki CM3289 Bedienungsanleitung

Hioki

Hioki MR8880-20 Bedienungsanleitung

Hioki

Hioki HiTester 3443-01 Bedienungsanleitung

Hioki

Hioki 8715-01 Bedienungsanleitung

Hioki

Hioki 3332 Bedienungsanleitung

Hioki

Hioki CM3286-01 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung