Hioki HITESTER 3184 Bedienungsanleitung

XXXX･XXXX Instruction Manual

XXXXXXX(形名末尾にあわせて位置移動）

3184

DIGITAL POWER HiTESTER

Instruction Manual

Oct. 1996 Revised edition 2

3184A981-02 96-10H

Contents

Introduction i

Inspection i

Safety Notes ii

Notes on Use iv

Chapter 1 Overview 1

1.1 Features 1

1.2 Names and Functions of Parts 2

Chapter 2 Specifications 7

2.1 General Specifications 7

Chapter 3 Basic Operating Principle 9

3.1 Active Power Measurements 9

3.2 Voltage and Current Measurements 10

3.3 Crest-Factor 11

Chapter 4 Operating Instructions 13

4.1 Operating Procedure 13

Chapter 5 3184-02 GP-IB Specifications 17

5.1 Outline 17

5.2 Interface Specifications 18

5.3 Panel Description 19

5.4 Talker Function 20

5.5 Listener Functions 21

5.6 Service Requests 23

5.7 Usage Precautions 24

5.8 Sample Programs 25

Chapter 6 Maintenance and Service 29

6.1 Fuse Replacement 29

6.2 Service 30

―――――――――――――――――――――――――――――――――――――――

Inspection

―――――――――――――――――――――――――――――――――――

ntroduction

nspection

Thank you for purchasing this HIOKI "3184 DIGITAL

POWER HiTESTER." To get the maximum performance

from the unit, please read this manual first, and keep

this at hand.

When the unit is delivered, check and make sure that it

has not been damaged in transit. In particular, check the

accessories, panel switches, and connectors.

If the unit is damaged, or fails to operate according to the

specifications, contact your dealer or HIOKI

representative.

Accessories

Fuse M0.5 A/250 V 1

(20×5.2 dia. mm arc-quencing midget)

Power cord 1

Instruction Manual 1

―――――――――――――――――――――――――――――――――――――――

Safety Notes

―――――――――――――――――――――――――――――――――――

WARNIN

Incorrect measurement procedures could result in

injury or death, as well as damage to the equipment.

Please read this manual carefully and be sure that

you understand its contents before using the

equipment. The manufacturer disclaims all

responsibility for any accident or injury except that

resulting due to defect in its product.

In the manual, this mark indicates explanations

which it is particularly important that the user read

before using the equipment.

afety Notes

This Instruction Manual provides information and

warnings essential for operating this equipment in a safe

manner and for maintaining it in safe operating

condition. Before using this equipment, be sure to

carefully read the following safety notes.

Safety symbols

iii

―――――――――――――――――――――――――――――――――――――――

Safety Notes

―――――――――――――――――――――――――――――――――――

DANGE

Indicates that incorrect operation presents extreme

danger of accident resulting in death or serious

injury to the user.

WARNIN

Indicates that incorrect operation presents

significant danger of accident resulting in death or

serious injury to the user.

CAUTIO

Indicates that incorrect operation presents

possibility of injury to the user or damage to the

equipment.

NOTE Denotes items of advice related to performance of

the equipment or to its correct operation.

The following symbols are used in this Instruction

Manual to indicate the relative importance of cautions

and warnings.

―――――――――――――――――――――――――――――――――――――――

Notes on Use

―――――――――――――――――――――――――――――――――――

DANGE

Always connect the voltage cable to the secondary

side of a breaker. On the secondary side of a

breaker, even if the lines are shorted the breaker

can trip and prevent an accident. On the primary

side, however, the current capacity may be large,

and in the event of a short-circuit there may be a

serious accident.

This unit cannot be used on voltage lines of 500

Vrms. If the voltage exceeds 500 VAC, there will be

a short-circuit accident or an electrocution accident

WARNIN

Be sure to connect the voltage input terminals and

current input terminals correctly. Measurement

which is attempted with the wiring connected

incorrectly may cause damage to the unit or a

short-circuit.

To prevent an electric shock and a short-circuit

accidents, shut off the power to the line to be

measured before connecting the load to the

terminals.

To avoid electric shock when replacing the fuse,

turn the power switch off, disconnect the power

code from the connector, and remove the input

cable from the object to be measured.

M0.5 A/250 V 20 mm×5.2 mm dia.

otes on Use

In order to ensure safe operation and to obtain maximum

performance from the unit, observe the cautions listed

below.

―――――――――――――――――――――――――――――――――――――――

Notes on Use

―――――――――――――――――――――――――――――――――――

WARNIN

Only use fuses of the specified type that is rated for

the specified current and voltage. Using a fuse that

does not meet the specifications or shorting the fuse

holder may cause an accident that might result in

injury or death.

CAUTIO

･Do not store or use the unit where it will be exposed to

direct sunlight, high temperatures, high humidity, or

condensation. If exposed to such conditions, the unit

may be damaged, the insulation may deteriorate, and

the unit may no longer satisfy its specifications.

･To avoid electric shock, the wiring which is used for

making the connections to the current input terminals

should have sufficient current carrying capacity and

insulation.

･To avoid damage to the unit, do not short the analog

output terminal and the GP-IB connector terminal and

do not input voltage to them.

･To avoid damage to the unit, do not subject the

equipment to vibrations or shocks during transport or

handling. Be especially careful to avoid dropping the

equipment.

･Before using the unit, make sure that the sheathing on

the leads is not damaged and that no bare wire is

exposed. If there is damage, using the unit could

cause electric shock.

―――――――――――――――――――――――――――――――――――――――

Notes on Use

―――――――――――――――――――――――――――――――――――

NOTE ･Accurate measurement may be impossible in locations

subject to strong external magnetic fields, such as

transformers and high-current conductors, or in locations

subject to strong external electric fields, such as radio

transmission equipment.

･When a measuring device such as a recorder or voltmeter

is connected to the analog output terminals, there is a

possibility of oscillatioin due to the input capacitance of

the measuring device.

If such oscillation occurs, insert a resistor (100 ohms or

thereabouts) in series between the analog output

terminals and the measuring device.

Inhaltsverzeichnis

Andere Hioki Messgerät Handbücher

Hioki

Hioki TM6102 Bedienungsanleitung

Hioki

Hioki CM4002 Bedienungsanleitung

Hioki

Hioki 3532-50 Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Hioki

Hioki 8715-01 Bedienungsanleitung

Hioki

Hioki 3196 Bedienungsanleitung

Hioki

Hioki 8847 Bedienungsanleitung

Hioki

Hioki 8870-20 Bedienungsanleitung

Hioki

Hioki MR8875 Bedienungsanleitung

Hioki

Hioki CKT3548 Bedienungsanleitung

Hioki

Hioki 9605-01 Bedienungsanleitung

Hioki

Hioki CM3286 Bedienungsanleitung

Hioki

Hioki CM4371 Bedienungsanleitung

Hioki

Hioki RM9010-01 Bedienungsanleitung

Hioki

Hioki CM4003 Bedienungsanleitung

Hioki

Hioki CT6845A Bedienungsanleitung

Hioki

Hioki 3246-60 Bedienungsanleitung

Hioki

Hioki MR8847-51 Bedienungsanleitung

Hioki

Hioki 3284 HiTester Bedienungsanleitung

Hioki

Hioki 3390 Bedienungsanleitung

Hioki

Hioki SP7001 Bedienungsanleitung

Hioki

Hioki CM4141 Bedienungsanleitung

Hioki

Hioki CM4141-90 Bedienungsanleitung

Hioki

Hioki PW3198 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung