Hirschmann HiSecOS EAGLE20 Bedienungsanleitung

Installation EAGLE20/30

Release

04/2014

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Security Router

EAGLE20/30

EAGLE20-0400...EAGLE30-0402...

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

EAGLE20/30 039 793-001-06-0414 - 14.04.2014

Installation EAGLE20/30

Release

04/2014 3

Contents

Safety instructions 5

About this manual 13

Key 14

1 Description 15

1.1 General device description 15

1.2 Device name and product code 16

1.3 Combination options 19

1.4 Device views 20

1.4.1 Front view 20

1.4.2 Rear view 21

1.5 Power supply 21

1.5.1 Working voltage with the characteristic value K 21

1.5.2 Working voltage with the characteristic value C 21

1.6 Ethernet ports 22

1.6.1 10/100 Mbit/s twisted pair port 22

1.6.2 100/1000 Mbit/s F/O port (optional) 22

1.6.3 100/1000 Mbit/s twisted pair port (optional) 22

1.7 Display elements 23

1.7.1 Device state 23

1.7.2 Additional status information 25

1.7.3 Input 25

1.7.4 Port state 25

1.8 Management interfaces 25

1.8.1 V.24 interface (external management) 25

1.8.2 SD card interface 26

1.8.3 USB interface 26

1.9 Input/output interfaces 27

1.9.1 Signal contact 27

1.9.2 Input 27

2 Installation 28

2.1 Unpacking and checking the content of the package 28

2.2 Installing the SD card (optional) 28

2.3 Installing and grounding the device 29

2.3.1 Installing the device onto the DIN rail 29

2.3.2 Grounding the device 30

4Installation EAGLE20/30

Release

04/2014

2.4 Installing an SFP transceiver (optional) 30

2.5 Connecting the terminal blocks 31

2.5.1 Working voltage with the characteristic value K 31

2.5.2 Working voltage with the characteristic value C 32

2.5.3 Signal contact 33

2.6 Operating the device 34

2.7 Connecting data cables 34

2.7.1 10/100 Mbit/s twisted pair port 34

2.7.2 100/1000 Mbit/s twisted pair port (optional) 34

2.7.3 100/1000 Mbit/s F/O port 35

2.8 Insert data in label area 35

3 Basic set-up 36

4 Maintenance and service 37

5Disassembly 38

5.1 Removing the device 38

5.2 Removing an SFP transceiver (optional) 39

6 Technical data 40

A Further Support 55

Installation EAGLE20/30

Release

04/2014 5

Safety instructions

General safety instructions

You operate this device with electricity. The proper and safe operation of

this device depends on proper handling during transportation, proper

storage and assembly, and conscientious operation and maintenance

procedures. Improper use of this device is associated with the risk of

personal injury or property damage.

Read this documentation as well as the safety instructions and

warnings before connecting any cables.

Never start operation with damaged components.

The device does not contain any service components. If the device is

not functioning correctly, or if it is damaged, switch off the voltage

supply and return the device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 40.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation EAGLE20/30

Release

04/2014

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding solely after disconnecting all other cables.

The overall shield of a connected shielded twisted-pair cable is connected

to the ground connector on the front panel as a conductor.

Working voltage

The working voltage is connected to the chassis through protective

elements exclusively.

Connect solely an working voltage that corresponds to the type plate

of your device.

Solely for device variants featuring working voltage with the

characteristic value K:

For the working voltage to be connected, make sure the following

requirements are met:

The supply voltage complies with the description on the data plate

of your device.

The power supply conforms to overvoltage category I or II.

The voltage supply has an easily accessible disconnecting device

(e.g. a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which line.

Disconnect device for equipment supplied from IT supply system,

shall disconnect both poles of mains supply.a

The electrical wires are voltage-free.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

a. IT supply system according to the technical standard UL 60950-1

Installation EAGLE20/30

Release

04/2014 7

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential. Otherwise, a fuse is

also located in the neutral conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

Supply with DC voltage:

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the working voltage input.

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the working voltage input.

The cross-section of the protective conductor is the same size as

or bigger than the cross-section of the power supply cables.

The power supply cables used are permitted for the temperature

range required by the use case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires solely if all the above

requirements are fulfilled.

For device variants with operating voltage characteristic value C

exclusively.

For the working voltage to be connected, make sure the following

requirements are met:

Relevant for North America:

The power supply is Class 2 compliant.

The power supply conforms to overvoltage category I or II.

The voltage supply has an easily accessible disconnecting device

(e.g. a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which line.

The electrical wires are voltage-free.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 40.

The wire diameter of the supply voltage at the input is at least 1

mm² (North America AWG16).

The wire diameter of the supply voltage at the input is at least 1

mm² (North America AWG16).

8Installation EAGLE20/30

Release

04/2014

The power supply cables used are permitted for the temperature

range required by the use case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires solely if all the above requirements

are fulfilled.

Internal fuses are triggered solely in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

working voltage and return the device to the plant for inspection.

For power supply connections with protective conductor connection:

First connect the protective conductor before connecting the wires for

the working voltage.

Only switch on the operating voltage for the device when the following

requirements are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the operating supply are connected

Signal contact

For the signal contact to be connected, make sure the following

requirements are met:

The signal contact connection wires are voltage-free.

The connected voltage is limited by a current limitation device or a

fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 40.

Start connecting the signal contact solely if all the above requirements are

fulfilled.

Installation site requirements

Verify that there is at least 4 in (10 cm) of space above and below the

device.

Verify that there is at least 0.8 in (2 cm) of space on the right and left

sides of the device.

Install the device in a fire protected enclosure according to EN 60950-

Solely for device variants featuring working voltage with the

characteristic value K:

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

Operate the device at the specified ambient temperature (temperature

of the ambient air at a distance of 2 inches (5 cm) from the device) and

at the specified relative humidity exclusively.

Installation EAGLE20/30

Release

04/2014 9

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

Make sure there is at least 3.94 inches (10 cm) of space in front of the

ventilation slits of the housing.

Install the device in the vertical position.

Instructions for Use in Hazardous Locations

SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D

HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS

ONLY.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT

EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS

KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF ANY

COMPONENT MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.

For USB and Relay: Install per Control Drawing 000172287DNR.

10 Installation EAGLE20/30

Release

04/2014

USB connection:

Equipment with non-incendive field wiring parameters.

USB entity parameters:

VOC =5.5V I

SC = 1.25 A

Ca= 10 µF La= 10 µH

For usage with Hirschmann USB devices certified and labelled

according Class I Div 2 hazardous location requirements such

as ACA21-USB EEC, or succeeding types.

Temperature Code: T4

Ambient Temperature rating:

Ta : 0rC to +60rC for “S” temperature types

Ta: -40rC to +70rC for “T” or “E” temperature types

(Refer to the temperature code of the type designation on the

device)

Relay contacts:

Equipment with non-incendive field wiring parameters.

Polarity is not relevant.

The relay terminals are dependent upon the following entity

parameters:

Vi= 30 V Ii= 90 mA

Ci= 2 nF Li= 1 µH

Power Supply unit type C: 24 V DC – 48 V DC

Power Supply unit type K: 110 V AC – 230 V AC or

60 V DC – 250 V DC

(Refer to the power supply code of the type designation on the

device)

Explosive Atmosphere

Class I, Division 2

Groups A, B, C, D

Hazardous Location

EAGLE20/30

ZĞůĂǇ

h^

Ordinary Location, Non-Hazardous Area,

non-explosive atmosphere

Rev.: 2 Doc. No.: 000172287DNR Page 1 of 2

Control Drawing for EAGLE20/30 devices according to Class I Division 2 Hazardous Locations

Andere Handbücher für HiSecOS EAGLE20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hirschmann Netzwerk-Router Handbücher

Hirschmann

Hirschmann PowerMICE Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Betriebsanleitung

Hirschmann

Hirschmann MICE MS20-1600 Series Bedienungsanleitung

Hirschmann

Hirschmann MACH 1020 Bedienungsanleitung

Hirschmann

Hirschmann RS40 series Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann EAGLE30-0402 series Bedienungsanleitung

Hirschmann

Hirschmann MICE MS20-0800 Series Bedienungsanleitung

Hirschmann

Hirschmann RS30-...U Series Bedienungsanleitung

Hirschmann

Hirschmann OWL LTE M12 Bedienungsanleitung

Hirschmann

Hirschmann OWL LTE Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann SPIDER Premium Line Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann Power MICE Bedienungsanleitung

Hirschmann

Hirschmann RSB20-0800T1T1 Bedienungsanleitung

Hirschmann

Hirschmann GECKO 4TX Bedienungsanleitung

Hirschmann

Hirschmann SPIDER 3TX-TAP Handbuch

Hirschmann

Hirschmann MACH104-16TX-PoEP+2X Series Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann RS2-5TX/FX Handbuch

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise