Hitachi RX Bedienungsanleitung

HITACHI Printer

Technical Manual

INK JET PRINTER FOR INDUSTRIAL MARKING

Model RX

Thank you for purchasing the Hitachi IJ Printer Model RX.

This printer employs a noncontact, ink-jet method to print onto a print target.

This instruction manual describes the basic operating procedures, maintenance procedures, and other detailed

handling procedures of the Hitachi IJ Printer Model RX.

If the printer is improperly handled or maintained, it may not operate smoothly and may become defective or

cause an accident. It is therefore essential that you read this manual to gain a complete understanding of the

printer and use it correctly.

After thoroughly reading the manual, properly store it for future reference.

IF you changed the language of screen by mistake,see the chapter 7.8 "Selecting Languages".

●Safety Precautions (1)

SAFETY PRECAUTIONS

●Before using the printer, thoroughly read the following safety precautions for optimum printer

use.

●You should observe the precautions set forth below in order to use the product properly and

avoid endangering you or other persons or damaging property. For the purpose of clarifying

the severity of injury or damage and likelihood of occurrence, the precautions are classified

into two categories, WARNING and CAUTION, which both describe a hazardous situations

that may arise if you ignore the precautions and perform an incorrect handling or operating

procedure. The precautions in these two categories are both important and must therefore

be observed without fail.

WARNING

WARNING is used to indicate the presence of a hazard which

may cause severe personal injury or death if the warning against

performing an incorrect handling procedure is ignored.

CAUTION

CAUTION is used to indicate the presence of a hazard which

may cause personal injury or property damage if the warning

against performing an incorrect handling procedure is ignored.

●If the warning in the CAUTION category is ignored, serious results may occur depending on

the situation.

●After the manual has been read, it must be stored in such a location that all printer operation

personnel can refer to it at all times.

●All the instructions set forth in this manual are important and must therefore be observed

without fail.

Pictograph Examples

The symbols are used to indicate precautions (including those related to

potential warnings) to be observed. Detailed information is furnished by a picture

within the symbol outline (a shock hazard is indicated by the example shown at

left).

The symbols are used to describe prohibited actions. The details of a

prohibited action are given by a picture within or near the symbol outline (the

example shown at left dictates that you must keep flames away).

The symbols are used to describe required actions. Detailed instructions are

given by a picture within the symbol outline (the example shown at left dictates

that a ground connection must be made).

User hereby agrees not to export or re-export this product to any end-user who the user

has reason to suspect may utilize the product for the design, development or reproduction

of nuclear, chemical or biochemical weapons.

Restrictions on Export

File management and USB management are carried out using eParts made from eSOL.

Ethernet is the product name of Xerox Corporation in America.

(2) ●Safety Precautions

SAFETY PRECAUTIONS (Continued)

WARNING

●Ensure that there is no flame- or arc-generating device around the

printer.

The ink and makeup are both flammable and may cause fire.

Fire can be generated by matches, lighters, cigarettes, heaters, stoves, gas

burners, welders, grinders and static electricity. Arcs may be generated from

open-type relays, switches, and brush motors. Before handling the ink and

makeup, remove static electricity from your body, peripheral equipment, and so

on. In the interest of safety, position a dry-chemical fire extinguisher near the

printer.

●Since the ink and makeup contain organic solvents, install the printer at

an adequately ventilated location.

Never install the printer in an enclosed space.

Connect exhaust equipment to the printer in order to prevent it from filling

with organic solvent vapor.

●Do not insert tweezers, a screwdriver, or any other metal article into the

ink ejection hole in the end of the print head.

When the printer is ready to print, a high voltage (approximately 6 kV) is applied

to the deflection electrode section in the print head.

Exercise caution to avoid electric shock, injury, and fire.

●Do not remove the outer covering.

A high voltage is applied to some sections of the printer.

Exercise caution to avoid electric shock and injury.

●Use an AC voltage of 100 to120 V or 200 to 240 V ±10% only and a

power frequency of 50 or 60 Hz only.

If the above requirements are not met, the electric parts may overheat and burn,

creating a risk of fire or electric shock.

●Never drain the ink or makeup waste solution into a public sewer system.

Waste disposal must comply with all appropriate regulations. Consult the

appropriate regulatory agency for further information.

●Exercise caution to avoid inadvertently disconnecting, forcibly pulling, or

bending piping tubes.

Since the ink and makeup in some portions of piping tubes are pressurized,

they may splash into your eyes or mouth or onto your hands or clothing.

If any ink or makeup enters your eyes or mouth, immediately flush with warm or

cold water and consult a physician.

●Safety Precautions (3)

SAFETY PRECAUTIONS (Continued)

WARNING

●While the printer is operating, do not look into the ink ejection hole in the

end of the print head.

Ink or makeup may enter your eyes or mouth or soil your hands or clothing.

If any ink or makeup enters your eyes or mouth, immediately flush with warm or

cold water and consult a physician.

●Before servicing the printer, be sure to stop the ink ejection.

Because ink or makeup may splash into your eyes or mouth or onto your hands

or clothing. If any ink or makeup enters your eyes or mouth, immediately flush

with warm or cold water and consult a physician.

●If an earthquake, fire, or other emergency occurs while the printer is

engaged in printing or just turned on, press the Main power switch to turn

off the power.

●The printer must be managed in compliance with all appropriate

regulations.

Read and understand the appropriate Material Safety Data Sheet (MSDS)

before using any ink or makeup.

●Use Hitachi approved consumables and periodic replacement parts.

Using products that are not designated by Hitachi could cause s failure in

certain functions.

●Warning for Mercury

-- THE LAMP IN THIS PRODUCT CONTAINS MERCURY.

RECYCLE OR DISPOSE OF IT ACCORDING TO APPLICABLE

ENVIRONMENTAL LAWS.

For Recycling and Disposal information, contact your government agency, the

Electronic Industries Alliance at www.eiae.org, and/or www.lamprecycle.org (in

the US), or the Electronic Product Stewardship Canada at www.epsc.ca (in

Canada). For more information, call 1-800-HITACHI (1-800-448-2244) (in the

US).

(4) ●Safety Precautions

SAFETY PRECAUTIONS (Continued)

WARNING

●When charging a refill of ink or makeup, exchanging ink, or otherwise

handling ink or makeup, take enough care not to spill ink or makeup.

If you spill any ink or makeup by mistake, wipe it off neatly and promptly

with wiping paper or something similar. Do not close the maintenance

cover until you make sure that the portion you have just wiped is

completely dry.

You must pay particular attention when you have spilled ink or makeup

inside the printer and it is not completely dry. Why? Because vapors of

ink or makeup will stay inside the printer and may catch on or cause a

fire.

If you find it hard to wipe the printer when it is turned on, stop it with the

maintenance cover open. Power it down, and then wipe it off again.

●If you wish to clean the casing of the printer with wiping paper

impregnated with makeup, be sure to do so with the power off.

Attempting to clean it when the power is on will cause makeup or vapors of

makeup to enter the printer, possibly catching on or causing a fire.

When the cleaning is over, open the maintenance cover and make sure that no

makeup has entered and no vapors remain inside.

●Should you find a leak of ink or makeup inside the printer while the

printer is running or being maintained, wipe it off promptly with wiping

paper or something similar. Then, with the maintenance cover open,

stop the printer, power it down, and repair the leak.

Continuing operation with a leak of ink or makeup will cause an anomaly,

resulting in abnormal printing.

Ink and makeup are flammable. They may therefore catch on or cause a fire.

●If you wish to receive ink particles in a beaker, for a printing test for

example, use an electrically conductive beaker and connect the beaker

securely to the ground.

Do not let the tip of the printing head enter the beaker.

Ink particles used for printing are electrically charged. An ungrounded beaker

has a gradually rising charge, possibly catching on or causing a fire.

●Ensure that all electrical wiring, connections and grounding comply with

applicable cords. Properly connect the printer to its dedicated ground.

Complete the above procedure to avoid electrical shock hazards.

●When welding, keep enough space between the IJ printer and the

welding work area to prevent the arc from starting a fire. Also, be sure to

insulate the printhead and IJ printer frame to keep the welding current

from flowing to the control section of the printer, and to make a separate

ground connection for the printer.

●Safety Precautions (5)

SAFETY PRECAUTIONS (Continued)

CAUTION

●Only persons who have completed an operator training course for

Hitachi IJP can operate and service the printer.

If the printer is operated or serviced incorrectly, it may malfunction or break

down.

●Do not attempt to make repairs for any purpose other than operation or

maintenance.

●Since the ink and makeup contain organic solvents, observe the

following handling precautions.

Secure adequate space for the ink/makeup handling area and printer

installation site. At least 200 m must be provided per print head.

Ensure that adequate ventilation is provided.

When handling the ink or makeup, wear protective gloves and safety goggles

to avoid direct skin contact. If the ink or makeup comes into contact with skin,

wash thoroughly with soap and warm or cold water.

When transferring the ink or makeup to or from a bottle, exercise caution to

prevent it coming into contact with the printer or surrounding articles.

If there is any spillage, immediately wipe it clean using a cloth moistened

with makeup.

●Ink and makeup must be stored as flammable liquids. Storage must

comply with local regulatory requirements. Consult the appropriate

regulatory agency for further information.

●If extraneous noise enters the printer, it may malfunction or break down.

For maximum noise immunity, observe the following installation and wiring

precautions.

Ensure that 100 to 120 VAC or 200 to 240 VAC power cables are not

bundled with other power supply cables.

Insulate the printer main body and print head so that they do not come into

direct contact with the conveyor or other devices.

If the employed print target detector is housed in a metal case, use a plastic

mounting brace for the purpose of insulating the detector from the conveyor

and other devices.

Be sure that the print target detector wiring is not bundled together with other

power supply cables.

●Please make sure the print status and print content are correct each time when

you start operation of IJP.

●Please implement periodical checkup of print status in the process, even

including during production.

●A touch panel is employed for data entry to operation screen.

When manipulating the Touch panel, use only fingers. If the touch panel is

operated with metal and/or sharp objects such as ball point pen, it may

malfunction or break down.

(6) ●Safety Precautions

SAFETY PRECAUTIONS (Continued)

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

●Contents 1

1. DELIVERED GOODS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2. INSTALLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . 2-1

3. INSTALLATION CHECK ITEMS . . . . . . . . . . . . . . . . . . . . 3-1

3.1 Print head air purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Setting functions which can be performed . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.3 Selecting user when power is turned on . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

4. ELECTRIC SIGNAL CONNECTION . . . . . . . . . . . . . . . . . 4-1

4.1 Wiring precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2 Input/output (I/O) signal connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

4.2.1 Wiring the I/O line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

4.2.2 Connection to input/output (I/O) terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.3 Input/output (I/O) specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4.3.1 Print target detector input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4.3.2 Product speed matching function using a rotary encoder . . . . . . . . . . . . . . . . . . . . 4-12

4.3.3 Input function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

4.3.4 Output function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

4.3.5 Product speed matching function without a rotary encoder (RX-S only) . . . . . . . . . 4-24

5. COMMUNICATION (Optinal on RX-B) . . . . . . . . . . . . . . . 5-1

5.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.2 Setting Communication Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

5.2.1 Setting Communication Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

5.5.2 Transmission Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

5.3 Transmission Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

5.3.1 Common Transmission Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

5.3.2 Printings Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

5.3.3 Print Data Recall Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

5.3.4 Print data registration transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

5.3.5 Print Condition Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

5.3.6 Calendar Conditions Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

5.3.7 User Pattern Character Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22

5.3.8 On-line/Off-line Transmission Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29

5.3.9 Remote Operation Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30

5.3.10 Time control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31

CONTENTS

2 ●Contents

5.4 Code Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33

5.4.1 Code Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33

5.4.2 Header Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42

5.5 Communication Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44

5.5.1 Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44

5.5.2 Response Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44

5.6 Communication Monitor Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-50

5.7 Warning Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51

5.8 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53

5.8.1 Notes on Product speed matching Feature Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53

5.8.2 Notes on Print Condition Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53

5.9 Communication Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54

5.9.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54

5.9.2 Description of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55

5.9.3 External Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58

5.9.4 Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-59

6. CIRCULATION SYSTEM WORK AND ADJUSTMENT

METHOD . . . . . . . . . . .6-1

6.1 Circulation control screen operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.2 Circulation control contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

6.3 Replacing the ink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

6.4 How to correct ink stream bending and nozzle clogging . . . . . . . . . . . . . . 6-7

6.4.1 Nozzle backwash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

6.4.2 Nozzle orifice disassembly and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

6.5 Stream alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

6.6 Cleaning the recovery line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

6.7 Replacing the ink filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

6.8 Replacing the recovery filter and makeup filter . . . . . . . . . . . . . . . . . . . . 6-16

6.9 Adjusting the pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18

6.10 Excitation V adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19

6.11 Ink drop state check method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22

6.12 Draining ink from the main ink tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24

6.13 Test of solenoid valve/pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25

6.14 Long-term Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26

6.14.1 Process prior to long-term shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27

6.14.2 Startup process after long-term shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32

●Contents 3

7. MAINTENANCE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . 7-1

8. SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.1 Outside Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.2 Electrical Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.3 Circulation System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

9. APPENDIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

●Barcode, 2-dimensional code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

●Setting high-speed printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

●Change of Buttons, Icons and Status Colors . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

●Icon List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9

●Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

Andere Handbücher für RX

Inhaltsverzeichnis

Andere Hitachi Drucker Handbücher

Hitachi

Hitachi DDS 40 Bedienungsanleitung

Hitachi

Hitachi UX2 Series Bedienungsanleitung

Hitachi

Hitachi UX Twin Nozzle Bedienungsanleitung

Hitachi

Hitachi UX2 Series Bedienungsanleitung

Hitachi

Hitachi ScanCenter Referenzhandbuch

Hitachi

Hitachi PH Bedienungsanleitung

Hitachi

Hitachi IJ RX2 Bedienungsanleitung

Hitachi

Hitachi UX Verdrahtungsschema

Hitachi

Hitachi SL1 Bedienungsanleitung

Hitachi

Hitachi PXR Bedienungsanleitung

Hitachi

Hitachi UX2 Series Installations- und Betriebsanleitung

Hitachi

Hitachi UX2 Series Bedienungsanleitung

Hitachi

Hitachi UX Twin Nozzle Bedienungsanleitung

Hitachi

Hitachi IJ UX Bedienungsanleitung

Hitachi

Hitachi PB Series Bedienungsanleitung

Hitachi

Hitachi DDS 40 Bedienungsanleitung

Hitachi

Hitachi RX Bedienungsanleitung

Hitachi

Hitachi RX2 Bedienungsanleitung

Hitachi

Hitachi IJ UX2 Bedienungsanleitung

Hitachi

Hitachi IJ UX Bedienungsanleitung

Hitachi

Hitachi PXR Series Bedienungsanleitung

Hitachi

Hitachi UX2 Series Bedienungsanleitung

Hitachi

Hitachi UX Twin-Nozzle Bedienungsanleitung

Hitachi

Hitachi UX2 Series Montageanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung