Hitachi 50V500 - UltraVision Digital - 50" Rear Projection... Bedienungsanleitung

LCD REAR PROJECTION TELEVISION

50V500

60V500

OPERATING GUIDE

IMPORTANT SAFETY INSTRUCTIONS 2-3

FIRST TIME USE 4-22

THE REMOTE CONTROL

ON-SCREEN DISPLAY

USEFUL INFORMATION INDEX 69-80

44-68

23-43

Locks

Chan. Manager

Aspect

Audio

Video

Move

SEL

Sel

Setup

As an ENERGY STAR®Partner, Hitachi, Ltd. has determined that this

product meets the ENERGY STAR®guidelines for energy efficiency.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI LCD REAR PROJECTION TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this

section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you

obtain from it to the proper operation of your HITACHI television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improb-

able event that a safety problem should be discovered in your product model.

Follow all warnings and instructions marked on this television.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral tri-

angle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of a

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to

alert the user to the presence of important operating and mainte-

nance (servicing) instructions in the literature accompanying the

appliance.

NOTE: • There are no user serviceable parts inside the television.

•Model and serial numbers are indicated on back side of the television.

POWER SOURCE

THIS TELEVISION IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE

POWER CORD INTO A 120 VOLT 60Hz OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION’S (POLARIZED) PLUG WITH AN

EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMI-

NAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE TELEVISION TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE

SPECIFIED VOLTAGE.

CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other haz-

ards. If the television does not operate properly, unplug the television and call your authorized dealer or

service center.

NOTE: This television receiver will display television closed captioning, ( or ), in accordance with

paragraph 15.119 of the FCC rules.

CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not express-

ly approved by HITACHI could void the user’s authority to operate the television.

MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that

are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s

authority to operate the equipment.

WARNING: • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO RAIN OR

MOISTURE.

•THE TELEVISION SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS

FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE TELEVISION.

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Follow all warnings and instructions marked on this television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or ground-

ing-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades

and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for replacement

of the obsolete outlet.

10. Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use the attachments/accessories specified by the man-

ufacturer.

12. Use only with the cart, stand, tripod, brack-

et, or table specified by the manufacturer,

or sold with the apparatus. When a cart is

used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15. Televisions are designed to comply with the recommended

safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or top, of the

cabinet which could cause the product to overturn resulting

in product damage and/or personal injury.

16. Follow instructions for wall, shelf or ceiling mounting as rec-

ommended by the manufacturer.

17. An outdoor antenna should not be located in the vicinity of

overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be sure the

antenna system is grounded so as to provide some protec-

tion against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No.

70-1984, provides information with respect to proper ground-

ing for the mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of grounding

connectors, location of antenna-discharge unit, connection to

grounding electrodes and requirements for the grounding

electrode.

Note to the CATV system installer: This reminder is provid-

ed to call the CATV system installer’s attention toArticle 820-

40 of the NEC that provides guidelines for proper grounding

and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close

to the point of cable entry as practical.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

Do not place any objects on the top of the televi-

sion which may fall or cause a child to climb to

retrieve the objects.

Disposal of this product may require specific

instructions pertaining to your resident state. For

disposal or recycling information, please contact

your local authorities or the Electronic Industries

Alliance: www.eiae.org.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require

prior authorization from the broadcaster or owner of the video program material.

•The lamp in this product contains Mercury. Dispose of properly in accordance with applicable environmental laws.

For Recycling and Disposal information, contact your respective governmental agencies or the Electronic Industries

Alliance at www.eiae.org (in the U.S.) or Electronic Product Stewardship Canada at www.epsc.ca (in Canada).

ACCESSORIES

1. Remote Control Unit CLU-5729TSI (Part No. HL01829).

2. Two “AA” size, 1.5V batteries (For Remote Control Unit).

3. Two IR Mouse Cables (Part No. EY01641).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the

cover off.

2. Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs

and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Lift up on tab to

remove back cover.

(Remote Control)

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

Check to make sure you have the following accessories before disposing of the packing material.

POWER

TV VCR CBL

DVD

456

789

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID1

VID2

VID3

VID4

VID5

PVR

CD AMP

VIDEO

CLU-5729TSI

REMOTE CONTROL BATTERIES

(“AA”) IR MOUSE

CABLE

FIRST TIME USE

OPTIONAL LCD REAR PTV STAND (NOT INCLUDED, ORDER SEPARATELY)

PART NAME PART NO.

50” LCD Rear PTV Stand H520445

SP50W

60” LCD Rear PTV Stand H520446

SP60W

CUSTOM HITACHI TELEVISION STAND

Excellent for VCR and video tape storage.

CAUTION: 1. This SP50W LCD stand for use only with Hitachi 50V500. Use with other apparatus is capable of resulting

in instability causing possible injury.

2. This SP60W LCD stand for use only with Hitachi 60V500. Use with other apparatus is capable of resulting

in instability causing possible injury.

HOW TO SET UP YOUR NEW HITACHI LCD REAR PTV

ANTENNA

Unless your LCD Rear PTV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is

recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and

multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location

selected allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can

become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI LCD Rear PTV is its large viewing screen. To see this large screen at its best, test various locations

in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as

the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the

reflection or the TV can be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing

the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For

best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side

or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker

placement for best performance.

FIRST TIME USE

IMPORTANT NOTES:

1. A small number of missing, discolored, or lit all the time dots or pixels is characteristic of TFT LCD technology due to

manufacturing process for such technology irrespective of manufacturer. If your LCD has defective pixels, it should not be

considered defective.

2. Since LCD Rear PTV incorporates a high pressure lamp to display an image, it may take about one minute for the picture to

become stable, after the power has been turned on. After extended use, the picture may darken, the color may look unusual,

or the lamp “goes out,” (burns out). You may hear a “pop” sound when the lamp “goes out.” These are common

characteristics of the lamp, and should not be considered defective.

3. LCD Rear PTV incorporates an advanced cooling fan system to prevent from overheating. If you hear the cooling fan, it should

not be considered defective.

4. If you hear a “cracking” sound from the TV cabinet, it is due to the TV’s cabinet expanding and contracting due to room

temperature changes. It has no effect on the TV’s functions.

5. The LCD Rear PTV cabinet is constructed with all plastic. Make sure to place it on a flat surface. An uneven surface might

warp the cabinet and reduce the picture quality.

HOOK-UP CABLES AND CONNECTORS

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV

coaxial cable to the ANT A (75-Ohm) terminal. If you have a second antenna or

cable TV system, connect the coaxial cable to the ANT B terminal.

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or

UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into

the antenna terminal on the TV.

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect

the cables to the antenna mixer. Consult your dealer or service store for the

antenna mixer.

To outdoor antenna

or CATV cable

To second antenna

or cable system

To outdoor VHF

or UHF antenna

From UHF antenna

ANT A/ANT B From outdoo

antenna or

CATV System

Antenna Mixer

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.

For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output

and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna

adapter (300-Ohm to 75-Ohm).

Phono Connector

Used on all standard video and audio cables which connect to

inputs and outputs located on the television’s rear jack panel

and front control panel.

“F” Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the antenna

jack on the television.

S-Video (Super Video) Connector

This connector is used on camcorders, VCRs and laser- disc

players with an S-Video feature in place of the

standard video cable to produce a high quality picture.

IR Mouse Cable (Provided)

Connect the IR Mouse Cable to the IR BLASTER output of your

TV when using the A/V Network feature. You must place the IR

mouse transmitter in front of the IR sensor of your external

components. This connection allows your TV to control your

external components without using your external component’s

remote control.

Digital Visual Interface (DVI) Connection Cable

This cable is used to connect external devices with DVI-HDTV

output capability.

FIRST TIME USE

FRONT PANEL CONTROLS

INPUT 5

S-VIDEO EXIT

INPUT

SELECT

MENUVOL- VOL+ CH- CH+















VIDEO AUDIO

L/MONO R

PHOTO MC



  

PUSH



PUSH

MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This

button also serves as the SELECT button when in MENU mode.

INPUT/EXIT button

Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source. Your selection is shown

in the top right corner of the screen. This button also serves as the EXIT button when in MENU mode.

CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as

the cursor down () and up () buttons when in MENU mode.

VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve

as the cursor left () and right () buttons when in MENU mode. When the TV power is turned OFF at a volume level 31 or greater,

the volume level will default to 30 when the TV is turned ON. However, if it is set to a level 30 or less, the volume level will be at

the level it was set when the TV is turned ON.

FRONT INPUT JACKS (INPUT 5)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording.

Press the INPUT/EXIT button on the front control panel until VIDEO: 5 appears in the top right corner of the TV screen. If you have

mono sound, insert the audio cable into the left audio jack.

PHOTO MC

Insert a PC card adapter with your Photo memory card to view the digital still pictures (see page 27).

To view your digital pictures, an adapter is required. Below are adapters that are tested with your television. Please find out which

memory card you have and acquire it from your local source.

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on your choice (see page 33). To change antenna source, press the ANT button on your remote control.

FIRST TIME USE

FRONT PANEL CONTROLS

IR RECEIVER/LEARNING AV NET sensor

The screen area acts as the IR receiver (remote sensor) and the LEARNING AV NET sensor of the TV. When using the remote

control, point it towards the screen for best response.

POWER button

Press this button to turn the TV on or off.

POWER light

This light is on during normal operation.

Light Blinking Slowly (2 seconds): television lamp is cooling down. It takes 12-15 seconds to warm up and about 2 minutes to cool

down.

TEMP indicator

This light is off during normal operation.

If this indicator is lit, the optic unit is too hot. If this indicator is blinking, the cooling fan has stopped. Please call service.

LAMP indicator - NORMAL OPERATION INDICATOR IS OFF

If light is lit, the lamp has failed. See page 69-72 for lamp replacement procedure. Consult your Hitachi dealer for proper part.

If light is blinking, lamp cover is not assembled securely after replacement.

PHOTO MC LED LIGHT INDICATOR

Shows the status of the memory card (see page 27).

NO LAMP LIGHT

or BROKEN LAMP

WRONG LAMP UNIT

ASSEMBLY / LAMP

DOOR OPEN

Too hot inside the

OPTIC unit

COOLING FAN STOPPED

NORMAL

OPERATION

COOL DOWN

LIGHT ON

BLINKING

LIGHT ON

BLINKING

LIGHT ON

SLOWLY BLINKING

INDICATOR INDICATION MEANING ACTION

LAMP LED

TEMP

LED

POWER

Need to replace if

LAMP still does not light by

“Power On” again.

Check assembly condition of

LAMP UNIT

Call for Service

NOTES:

2. If the LAMP, TEMP, and POWER LED are blinking in the order below, the television is warming up.

POWER TEMP LAMP

FIRST TIME USE

IMPORTANT NOTES:

1. A small number of missing, discolored, or lit all the time dots or pixels is characteristic of TFT LCD technology due to

manufacturing process for such technology irrespective of manufacturer. If your LCD has defective pixels, it should not be

considered defective.

2. Since LCD Rear PTV incorporates a high pressure lamp to display an image, it may take about one minute for the picture to

become stable, after the power has been turned on. After extended use, the picture may darken, the color may look unusual,

or the lamp “goes out,” (burns out). You may hear a “pop” sound when the lamp “goes out.” These are common

characteristics of the lamp, and should not be considered defective.

3. LCD Rear PTV incorporates an advanced cooling fan system to prevent from overheating. If you hear the cooling fan, it should

not be considered defective.

4. If you hear a “cracking” sound from the TV cabinet, it is due to the TV’s cabinet expanding and contracting due to room

temperature changes. It has no effect on the TV’s functions.

FRONT PANEL JACKS AND CONNECTORS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

INPUT 5

S-VIDEO VIDEO AUDIO

L/MONO RINPUT 5

S-VIDEO VIDEO AUDIO

L/MONO R

FIRST TIME USE

REAR PANEL JACKS

Antenna Input/Output

ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture.

ANT B- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT B can only be displayed as a main picture. ANT B cannot be

displayed as a sub-picture.

TO CONVERTER- This antenna output allows the ANT A connection to pass directly to a different source, such as a cable box,

only when ANT B is displayed as a main picture.

Audio/Video Inputs 1, 2, 3 and 4

The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect

external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable

into the left audio jack.)

MONITOR OUT

These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video

output.

AUDIO TO HI-FI Output

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be

controlled by the television’s main volume.

CENTER IN (Input)

This jack is for stereo amplifiers with center signal capability. This feature allows the TV speakers to be used as a center speaker.

The TV must be set as a center channel by selecting “TV as Center” on the Internal Speakers Settings of theAudio Menu (see page

50).

S-VIDEO Inputs 3 and 4

Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a

time.







 







CENTER

DVI-HDTV

ANTA

CONVERTER

ANT B

R(MONO)/L

BLASTER

AUDIO

TO HI-FI

S-VIDEO

Y/VIDEO

R(MONO)/L

R(MONO)/L VIDEO

RL VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

AUDIO

NOTE: S-VIDEO output may be used for recording only when the input is of S-VIDEO type.

FIRST TIME USE

Andere Handbücher für 50V500 - UltraVision Digital - 50" Rear Projection...

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektionsfernsehen Handbücher

Hitachi

Hitachi 55VG825 - 55" Rear Projection TV Bedienungsanleitung

Hitachi

Hitachi CT5582K Bedienungsanleitung

Hitachi

Hitachi 13K 50UX26B Bedienungsanleitung

Hitachi

Hitachi 62VS69 - UltraVision VS69 Series Bedienungsanleitung

Hitachi

Hitachi 50GX49B Bedienungsanleitung

Hitachi

Hitachi 61SWX01W Bedienungsanleitung

Hitachi

Hitachi 51SWX20B Bedienungsanleitung

Hitachi

Hitachi 60UX58B Bedienungsanleitung

Hitachi

Hitachi 46UX51K Bedienungsanleitung

Hitachi

Hitachi 50UX58B Bedienungsanleitung

Hitachi

Hitachi 53SBX59B Bedienungsanleitung

Hitachi

Hitachi 50V720 - 50" Rear Projection TV Bedienungsanleitung

Hitachi

Hitachi 55DMX01WD Bedienungsanleitung

Hitachi

Hitachi 43FDX10B Bedienungsanleitung

Hitachi

Hitachi 57UWX20B Bedienungsanleitung

Hitachi

Hitachi 53SDX20BB Bedienungsanleitung

Hitachi

Hitachi 61SWX10B Bedienungsanleitung

Hitachi

Hitachi 46EX1B Bedienungsanleitung

Hitachi

Hitachi 46EX3B Bedienungsanleitung

Hitachi

Hitachi 42V515 - 42" Rear Projection TV Bedienungsanleitung

Hitachi

Hitachi 51XWX20B Bedienungsanleitung

Hitachi

Hitachi 43FDX20B Bedienungsanleitung

Hitachi

Hitachi 51F520 Bedienungsanleitung

Hitachi

Hitachi 55FX20B Bedienungsanleitung

Beliebte Projektionsfernsehen Handbücher anderer Marken

Samsung

Samsung ST-43T6P Bedienungsanleitung

Toshiba

Toshiba ColorStream TP50G60 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric WD-65734 Bedienungsanleitung

Optoma

Optoma EP652A Bedienungsanleitung

Samsung

Samsung SP43T8HPX/XEC Bedienungsanleitung

Philips

Philips 28PW6006 - annexe 1 Bedienungsanleitung

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Benutzerhandbuch

Philips

Philips 43PP8421 Bedienungsanleitung

RCA

RCA P52950 Bedienungsanleitung

Sony

Sony KP-51DS1U Bedienungsanleitung

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Bedienungsanleitung

Pioneer

Pioneer Elite PRO 510HD Bedienungsanleitung

Philips

Philips 43PP8421 Handbuch

JVC

JVC I'Art Pro AV-48P776 Bedienungsanleitung

Sony

Sony GRAND WEGA KDF-55XS955 Bedienungsanleitung

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Bedienungsanleitung

Toshiba

Toshiba 42HM66 - 42" Rear Projection TV Bedienungsanleitung

Philips

Philips 50PL9200D Bedienungsanleitung