HMS Anybus Communicator IIoT Benutzerhandbuch

Anybus®Communicator™

IIoT

STARTUP GUIDE

SP2444 1.0 en-US ENGLISH

Important User Information

Liability

Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB

of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,

HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous

product development. The information in this document is subject to change without notice and should not

be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no

responsibility for any errors that may appear in this document.

There are many applications of this product. Those responsible for the use of this device must ensure that

all the necessary steps have been taken to verify that the applications meet all performance and safety

requirements including any applicable laws, regulations, codes, and standards.

HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems

that may arise as a result from the use of undocumented features, timing, or functional side effects found

outside the documented scope of this product. The effects caused by any direct or indirect use of such

aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.

The examples and illustrations in this document are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular implementation, HMS Industrial Networks

AB cannot assume responsibility for actual use based on these examples and illustrations.

Intellectual Property Rights

HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product

described in this document. These intellectual property rights may include patents and pending patent

applications in the USA and other countries.

Anybus®is a registered trademark of HMS Industrial Networks AB. All other trademarks mentioned in this

document are the property of their respective holders.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Preface 3 (12)

1 Preface

1.1 About This Document

This document describes how to install the Anybus Communicator IIoT.

For additional documentation and software downloads, FAQs, troubleshooting

guides and technical support, please visit www.anybus.com/support.

1.2 Document Conventions

The following formatting conventions are used in this document to indicate safety

information and other content of specific importance:

WARNING

This instruction must be followed to avoid a risk of death or serious injury.

Caution

This instruction must be followed to avoid a risk of personal injury.

This instruction must be followed to avoid a risk of reduced functionality

and/or damage to the equipment, or to avoid a network security risk.

This is additional information which may facilitate installation and/or

operation.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 4 (12)

2 Installation

2.1 Installation Overview

Prerequisites

The following items are required for installation and basic configuration:

• Configuration cable

• Subnetwork cable

• Ethernet cable

• Anybus Configuration Manager - Communicator RS-232/422/485

(4.5.0.0 or later)

• Anybus Configuration Manager - IIoT

• IPconfig (3.2.1.1 or later)

The Anybus Configuration Manager and IPconfig applications can be

downloaded from www.anybus.com/support.

Basic installation steps

1. Mount the Anybus Communicator on the DIN rail.

2. Connect the serial and IIoT network interfaces.

3. Connect the configuration cable between the gateway and a PC.

4. Connect the power cable and apply power.

5. Check the LED indicators to verify that the gateway is running and that the

serial and IT networks are connected. See LED Indicators, p. 9.

6. Use Anybus Configuration Manager - Communicator to set up the data

exchange configuration in the Anybus Communicator.

7. Use IPconfig to configure the TCP/IP settings for the Anybus Communicator.

8. Use Anybus Configuration Manager - IIoT to create a tag configuration and

transfer it to the Anybus Communicator.

9. Connect to the web interface of the Anybus Communicator and configure

MQTT/OPC UA communication.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 5 (12)

2.2 DIN Rail Mounting

The unit must be electrically grounded through the DIN rail for EMC

compliance.

Mount on DIN rail

Fig. 1 Push down to mount or remove

1. Hook the unit onto the upper lip of the rail and push gently downwards.

2. Push the unit towards the rail until it snaps into place.

Remove from DIN rail

1. Push the unit gently downwards on the rail.

2. Pull the bottom end of the unit free of the rail and remove it.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 6 (12)

2.3 Connectors and Indicators

2.3.1 Overview

Fig. 2 Overview

1LED indicators

2DIN rail mount

3Power connector

4Serial subnetwork interface

5PC connector

6IIoT network interface

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 7 (12)

2.3.2 Serial Subnetwork Interface

Fig. 3 D-sub connector (DE-9F)

Pin Description RS-232 RS-422 RS-485

1 +5 V Output (100 mA max.) xxx

2 RS-232 Rx x

3 RS-232 Tx x

4(reserved)

5Signal Ground xxx

6 RS-422 Rx + x

7RS-422 Rx - x

8 RS-485 + / RS-422 Tx + x x

9 RS-485 - / RS-422 Tx - x x

Housing Shield xxx

Do not connect Signal Ground to Protective Earth (PE) of other nodes on

the subnetwork as this may damage the on-board serial transceivers.

Connect it only to the Signal Ground on other nodes.

Bias and/or termination resistors may be required depending on the type of

serial network. Please refer to the User Manual for more information.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 8 (12)

2.3.3 Power Connector (2 pin)

Connecting power with reverse polarity or using the wrong type of power

supply may damage the equipment. Make sure that the power supply is

connected correctly and of the recommended type.

Pin Signal

1 +24 VDC

2 Power Ground

2.3.4 PC Connector (RJ11)

Pin Signal

1 GND ( signal ground)

2 GND (signal ground)

3 RS-232 Rx (input)

4 RS-232 Tx (output)

2.3.5 Ethernet Connector (RJ45)

Pin Signal Description

1 TD+ Transmit data +

2 TD- Transmit data -

3 RD+ Receive data +

6 RD- Receive data -

4,5,7,8 -(reserved)

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Installation 9 (12)

2.4 LED Indicators

1 2

LED 1 to 4 Model-specific information

LED 5 Serial subnetwork status

LED 6 Device status

LED Indication Meaning

1 - Network Status

Off Offline or no power

Green Online, IP address assigned

Green, flashing No IP address assigned or no link

Red Fatal error, IP address conflict

Alternating Red/Green Firmware update in progress

2 - Module Status

Off No power or IP address conflict

Green Normal operation

Red Fatal error

Alternating red/green Firmware update in progress

3 - Link/Activity 1

4 - Link/Activity 2

Off Link not detected or no power

Green Link established (100 Mbit/s)

Green, flickering Link activity (100 Mbit/s)

Red Link established (10 Mbit/s)

Red, flickering Link activity (10 Mbit/s)

5 - Subnet Status Off No power

Green Running

Green, flashing Running, one or more transaction

errors

Red Transaction error/timeout or subnet

stopped

6 - Device Status Off No power

Green Initializing

Green, flashing Running

Red Bootloader mode

Alternating red/green Configuration invalid or missing

The Link/Activity LED indicators will show a red light for 10 Mbit/s connections.

This is normal and does not indicate an error.

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Technical Data 10 (12)

3 Technical Data

3.1 General Specifications

Model name Anybus Communicator IIoT

Order code AB7079-B

Dimensions (L x W x H) 120 x 75 x 27 mm

Weight 150 g

Operating temperature 0 to +55 °C (IEC 60068-2-1 and IEC 60068-2-2)

Storage temperature -40 to +85 °C (IEC 60068-2-1 and IEC 60068-2-2)

Humidity range 5–95 % RH, non-condensing (IEC 60068-2-30)

Power supply 24 V ±10 % DC regulated power source

Current consumption Typical: 100 mA @ 24 VDC

Maximum: 200 mA @ 24 VDC

Galvanic isolation Yes, on both network sides

Mechanical rating IP20, NEMA rating 1

Mounting DIN rail (EN 50022)

Network shield conductance via DIN rail

Certifications See datasheet at www.anybus.com/support

3.2 Serial Interface

Serial application Interface Selectable RS-232, RS-422, RS-485

Maximum number of stations 31 nodes via RS-422 or RS-485

Protocol: Modbus RTU Modbus RTU Master - Query/Response

Protocol: ASCII/Vendor Specific Request/Response or Produce/Consume

Protocol: Rockwell DF1 DF1 Master

Anybus®Communicator™Startup Guide SP2444 1.0 en-US

Inhaltsverzeichnis

Andere HMS Tor Handbücher

HMS

HMS Anybus-X Bedienungsanleitung

HMS

HMS Anybus 024380-C Bedienungsanleitung

HMS

HMS Anybus X-gateway AB7800 Bedienungsanleitung

HMS

HMS Intesis WMP Bedienungsanleitung

HMS

HMS Netbiter EasyConnect Bedienungsanleitung

HMS

HMS Intesis INMBSOCP 0100 Series Montageanleitung

HMS

HMS Intesis KNX Mitsubishi Electric CC Bedienungsanleitung

HMS

HMS AB7307 Bedienungsanleitung

HMS

HMS Anybus-X AB7609 Bedienungsanleitung

HMS

HMS Intesis INBACSAM004O000 Bedienungsanleitung

HMS

HMS AnyBus-X J1939 Bedienungsanleitung

HMS

HMS Intesis INKNXMBM1000100 Montageanleitung

HMS

HMS Intesis Modbus Server Bedienungsanleitung

HMS

HMS Intesis INMBSHIS016O000 Bedienungsanleitung

HMS

HMS Intesis INKNXFGL016O000 Bedienungsanleitung

HMS

HMS Intesis IN776MHI00 O000 Series Montageanleitung

HMS

HMS Intesis KNX HITACHI VRF Bedienungsanleitung

HMS

HMS Intesis INBACHIT O000 Series Montageanleitung

HMS

HMS Anybus X-gateway CANopen Bedienungsanleitung

HMS

HMS HMS-EN2MB-R Bedienungsanleitung

HMS

HMS Anybus X-gateway AB7 Series Leitfaden

HMS

HMS Anybus Edge Bedienungsanleitung

HMS

HMS HGP 115 Installations- und Betriebsanleitung

HMS

HMS Intesis WMP Series Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt