HMS Anybus X-gateway Bedienungsanleitung

AAnnyybbuuss

®® XX--ggaatteewwaayy™™

USER MANUAL

HMSI-27-262 4.0 en-US ENGLISH

Important User Information

Disclaimer

The information in this document is for informational purposes only. Please inform HMS Industrial Networks of any

inaccuracies or omissions found in this document. HMS Industrial Networks disclaims any responsibility or liability

for any errors that may appear in this document.

HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous product

development. The information in this document shall therefore not be construed as a commitment on the part of

HMS Industrial Networks and is subject to change without notice. HMS Industrial Networks makes no commitment

to update or keep current the information in this document.

The data, examples and illustrations found in this document are included for illustrative purposes and are only

intended to help improve understanding of the functionality and handling of the product. In view of the wide range

of possible applications of the product, and because of the many variables and requirements associated with any

particular implementation, HMS Industrial Networks cannot assume responsibility or liability for actual use based on

the data, examples or illustrations included in this document nor for any damages incurred during installation of the

product. Those responsible for the use of the product must acquire sufficient knowledge in order to ensure that the

product is used correctly in their specific application and that the application meets all performance and safety

requirements including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will

under no circumstances assume liability or responsibility for any problems that may arise as a result from the use of

undocumented features or functional side effects found outside the documented scope of the product. The effects

caused by any direct or indirect use of such aspects of the product are undefined and may include e.g. compatibility

issues and stability issues.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Table of Contents Page

1 Preface ................................................................................................................................. 3

1.1 About This Document .......................................................................................................3

1.2 Document history ............................................................................................................3

1.3 Document Conventions.....................................................................................................4

1.4 Document-specific Conventions..........................................................................................4

2 Description .......................................................................................................................... 5

2.1 Introduction....................................................................................................................5

2.2 Data Exchange.................................................................................................................6

2.3 Status and Diagnostics ......................................................................................................7

2.4 Controlling the X-gateway from the Network ........................................................................9

2.5 Error Handling .................................................................................................................9

2.6 Data Mapping Examples.................................................................................................. 10

3 Installation......................................................................................................................... 11

3.1 DIN Rail Mount.............................................................................................................. 11

3.2 Connectors and Indicators ............................................................................................... 12

4 Anybus Configuration Manager ....................................................................................... 13

4.1 Introduction.................................................................................................................. 13

4.2 Setup........................................................................................................................... 14

4.3 Configuration ................................................................................................................ 14

A Technical Data ................................................................................................................... 15

This page intentionally left blank

Preface 3 (16)

1 Preface

1.1 About This Document

This document describes the functions and general configuration of the Anybus X-gateway.

Documentation and software for the specific fieldbus and Ethernet network interfaces can be

downloaded from www.anybus.com/support.

1.2 Document history

Version Date Description

1.00 2004-04-02 First release

2.00 2014-05-01 Major update

2.10 2014-08-26 Compliance information update

3.0 2017-01-23 Major rewrite

3.1 2018-03-23 Minor update

4.0 2019-03-19 Rebranding update, some graphics updated

Removed certification info (now in datasheet only)

This document now replaces SCM-1202-038.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Preface 4 (16)

1.3 Document Conventions

Ordered lists are used for instructions that must be carried out in sequence:

1. First do this

2. Then do this

Unordered (bulleted) lists are used for:

• Itemized information

• Instructions that can be carried out in any order

...and for action-result type instructions:

►This action...

→ leads to this result

Bold typeface indicates interactive parts such as connectors and switches on the hardware, or

menus and buttons in a graphical user interface.

Monospaced text is used to indicate program code and other

kinds of data input/output such as configuration scripts.

This is a cross-reference within this document: Document Conventions, p. 4

This is an external link (URL): www.hms-networks.com

This is additional information which may facilitate installation and/or operation.

This instruction must be followed to avoid a risk of reduced functionality and/or damage

to the equipment, or to avoid a network security risk.

Caution

This instruction must be followed to avoid a risk of personal injury.

WARNING

This instruction must be followed to avoid a risk of death or serious injury.

1.4 Document-specific Conventions

The following conventions are used specifically in this document:

• Hexadecimal values are written as NNNNh (the suffix hindicates hexadecimal notation).

• 16 and 32 bit values are stored in Motorola (big endian) format unless otherwise stated.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Description 5 (16)

2 Description

2.1 Introduction

The Anybus X-gateway consists of two Anybus fieldbus or Ethernet network interface modules

and an intelligent gateway platform which transfers data between the two networks.

The X-gateway can be configured via a USB port using a Windows-based application, Anybus

Configuration Manager. The on-board network interfaces are normally configured from the

respective networks, using third-party configuration tools.

Fig. 1 Anybus X-gateway concept overview

This document describes only the gateway platform. The network interfaces are described in

their own documentation.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Description 6 (16)

2.2 Data Exchange

Fig. 2 Anybus X-gateway data exchange

The terminology and definitions used for different types of data vary between different network

types. Most networks distinguish between fast, cyclical I/O data, and less time-critical acyclic

data. In the Anybus X-gateway these types of data are generally referred to respectively as I/O

Data and Parameter Data.

Each of the two network interfaces exchanges data on its network through its own buffer, which

can hold up to 512 bytes of data. The actual amount of data that can be exchanged depends on

the settings in the network interface and may therefore be significantly less than 512 bytes,

which is only the maximum size of the buffer. The default setting is 20 bytes in each direction.

See the documentation for the respective network interface for more information.

In addition to the I/O data the buffers may contain network status information and instructions

for controlling the network interface. Depending on the type of network interface this may be

general diagnostic information (Status Word), a list of the active slaves (Live List), or other

network-specific information. In a network master, part of the buffer may be used to start/stop

data exchange and to reset the gateway (Control Word).

The exchange of data between the buffers is separate from the network data exchange. While

the X-gateway ensures data consistency (where applicable), it does not feature any mechanisms

for synchronisation between the two networks.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Description 7 (16)

2.3 Status and Diagnostics

2.3.1 Status Word

Runtime status and diagnostic information can be provided through the Status Word, which (if

enabled) takes up the first two bytes of the output area (data to the network).

The Status Word is disabled by default and must be enabled for each network separately through

Anybus Configuration Manager.

(MSB) (LSB)

bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

Gateway Cycle Counter General Error Counter (reserved) Master Mode Init Run

Gateway Cycle Counter

A 4-bit counter, incremented for each successful gateway cycle (each time data has been

successfully transferred between the network interfaces).

General Error Counter

A 4-bit counter, incremented each time the throughput of the gateway exceeds 100 ms.

Master Mode (master configurations only)

If a network interface is confgured as a network master, these bits indicate the current operation

mode of the master to the other network.

The exact definition depends on the network interface type. See the documentation for the

respective interface for more information.

Init

Indicates if the other network interface has been initialized.

Bit set (1) = Other network interface successfully initialized

Bit cleared (0) = Could not initialize other network interface

Run

Indicates the status of the data exchange on the other network.

Bit set (1) = Other network is online and exchanging data

Bit cleared (0) = Other network is offline or not exchanging data

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Description 8 (16)

2.3.2 Live List (Master Configurations Only)

The Live List provides the active status of the slaves associated with an on-board network

interface acting as master. The list is assembled by the master interface and forwarded to the

other network each gateway cycle.

The Live List functionality is disabled by default and must be enabled for the master interface

through Anybus Configuration Manager.

Offset bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7

0Slave 0 Slave 1 Slave 2 Slave 3 Slave 4 Slave 5 Slave 6 Slave 7

1Slave 8 Slave 9 Slave 10 Slave 11 Slave 12 Slave 13 Slave 14 Slave 15

2Slave 16 Slave 17 Slave 18 Slave 19 Slave 20 Slave 21 Slave 22 Slave 23

3Slave 24 Slave 25 Slave 26 Slave 27 Slave 28 Slave 29 Slave 30 Slave 31

4Slave 32 Slave 33 Slave 34 Slave 35 Slave 36 Slave 37 Slave 38 Slave 39

5Slave 40 Slave 41 Slave 42 Slave 43 Slave 44 Slave 45 Slave 46 Slave 47

6Slave 48 Slave 49 Slave 50 Slave 51 Slave 52 Slave 53 Slave 54 Slave 55

7Slave 56 Slave 57 Slave 58 Slave 59 Slave 60 Slave 61 Slave 62 Slave 63

Bit set (1) = Slave active

Bit cleared (0) = Slave not active

The exact definition of each set or cleared bit depends on the network interface used. See the

documentation for the respective interface for more information.

2.3.3 Network-specific Status

Some network interfaces may provide additional registers or status lists. See the documentation

for the respective interface for more information.

Anybus®X-gateway™User Manual HMSI-27-262 4.0 en-US

Andere Handbücher für Anybus X-gateway

Inhaltsverzeichnis

Andere HMS Tor Handbücher

HMS

HMS Intesis INBACDAL1280200 Montageanleitung

HMS

HMS Intesis INKNXMBM1000100 Montageanleitung

HMS

HMS Intesis IN776MHI00 O000 Series Montageanleitung

HMS

HMS Anybus-X Bedienungsanleitung

HMS

HMS Intesis KNX Series Bedienungsanleitung

HMS

HMS Intesis KNX Bedienungsanleitung

HMS

HMS Netbiter EasyConnect Series Bedienungsanleitung

HMS

HMS Anybus HMS-EN2MB-R Bedienungsanleitung

HMS

HMS Anybus X-gateway CANopen Bedienungsanleitung

HMS

HMS Anybus Communicator CAN PROFINET IRT 2.32 Bedienungsanleitung

HMS

HMS Anybus Edge Bedienungsanleitung

HMS

HMS Anybus X-gateway AB7 Series Leitfaden

HMS

HMS Anybus 024380-C Bedienungsanleitung

HMS

HMS Intesis INMBSPAN016O000 Bedienungsanleitung

HMS

HMS HGP 115 Installations- und Betriebsanleitung

HMS

HMS AnyBus-X AB7607 Bedienungsanleitung

HMS

HMS Ixxat CAN@net NT 420 Bedienungsanleitung

HMS

HMS Anybus X-gateway Bedienungsanleitung

HMS

HMS Ewon Cosy+ Bedienungsanleitung

HMS

HMS Intesis INBACSAM004O000 Bedienungsanleitung

HMS

HMS Intesis IN485MHI001R000 Bedienungsanleitung

HMS

HMS Anybus X-Gateway Series Bedienungsanleitung

HMS

HMS Ewon Cosy+ Bedienungsanleitung

HMS

HMS Ixxat SG-gateway Benutzerhandbuch

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt