Hobby King Typhoon -EP Bedienungsanleitung

Specs:

Wing Span: 1250mm

Wing Area: 29.13 Sq dm

Length: 1106mm

Weight: 1350g w/o battery

Required:

otor: BL2820

Radio: 4 channels

4 * 9~12g servos

Battery: 3S~4S 11.1~14.8V 2200mAh ~ 2600mAh

ESC: 60A

Warning!

This item is not a toy. It has the potential to cause serious harm if mistreated. The user accepts all

responsibility in the assembly of this model. Always check the model to ensure it is free of damage and all

screws and control hardware is tight before each flight.

Wing Assembly

1) Wing control hardware and wing tube.

2) Cut covering at servo mounts.

3) Install aileron servo, secure with screws. Depending on your servo you may need short extension leads

to reach your receiver.

4) Check to make sure the pre-fitted “CA Style” hinges are centered on the centerline. Then glue the hinge

with thin CA glue. After the glue cures, flex the control surface a few times to make sure it moves freely.

5) Install aileron horn, secure with included screw.

6) Attach aileron control rod with supplied hardware. ake sure servo is centered and servo arm is installed

90 degrees to the control rod for best movement.

Tail Assembly

1) Tail control hardware, tailwheel, and elevator joiner.

2) Insert horizontal stabilizer to fuselage. Center it, then draw a line noting its position. Using a sharp hobby

knife remove the covering for vertical fin and horizontal stabilizer. Do not cut balsa underneath.

2a) The areas shown where covering was removed will provide a good wood to wood joint when gluing tail

parts to fuselage.

3) To install the elevator joiner, a small channel needs to be cut on each elevator half to accept the wire.

4) Drill a 2mm hole to install the elevator linkage rod. Try to keep the hole perpendicular to the hinge line

and centered on the control surface. When the elevator joiner is installed, it needs to keep both halves

even to prevent unwanted rolling tendencies.

5) Glue the elevator joiner wire to the elevator halves with thick CA glue or epoxy. Lay both halves flat on a

table while the glue cures.

6) Insert elevator to fuselage before installing horizontal stabilizer.

7) Insert stabilizer to fuselage, centering it on the area where the covering was previously removed. Glue

the stabilizer in place with thick CA or epoxy.

8) Glue hinges with thin CA glue. Flex control surface several times to check for proper movement.

9) Install elevator servo, secure with screws

10) Install elevator horn, secure with supplied screws and square backplate

11) Attach elevator control rod with supplied hardware

12) Glue the vertical fin with CA glue or epoxy

13) Bend the tail wheel steel wire after inserting it through the plastic bracket. There should be about 15mm

of wire after the bend. Cut off remainging wire.

14) Cut a small channel in the rudder to allow the tail wheel wire to sit even with the hinge line when

installed.

15) Drill a 2mm hole to accept the tail wheel wire. Drill it centered on the control surface so tail wheel is

straight, relative to the rudder.

16) Insert rudder and hinges to fuselage. Glue rudder hinges with thin CA glue. Flex several times to

ensure free movement of the control surface.

17) Glue tail wheel steel wire with thick CA or epoxy.

18) Install rudder servo, secure with screws

19) Feed rudder cables through the fuselage. Loop cable through threaded end, and secure with aluminum

crimp. Repeat for both sides. For best control, control cables should cross the fuselage. So, cable on right

side of servo, should exit left side of fuselage.

20) Install rudder horn, secure with screws and 2 nut.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hobby King Spielzeug Handbücher

Hobby King

Hobby King Gee Bee R3 Bedienungsanleitung

Hobby King

Hobby King skipper Bedienungsanleitung

Hobby King

Hobby King Decathlon Bedienungsanleitung

Hobby King

Hobby King spitfire Bedienungsanleitung

Hobby King

Hobby King DragonFly EDF Bedienungsanleitung

Hobby King

Hobby King Fokker Dr.I Bedienungsanleitung

Hobby King

Hobby King Maestro-46 Bedienungsanleitung

Hobby King

Hobby King Tanager Glider Bedienungsanleitung

Hobby King

Hobby King FALCON TRAINER Bedienungsanleitung

Hobby King

Hobby King go Discover Bedienungsanleitung

Hobby King

Hobby King ASK-2100 Bedienungsanleitung

Hobby King

Hobby King Airoso F3A Bedienungsanleitung

Hobby King

Hobby King Blanik Bedienungsanleitung

Hobby King

Hobby King YAK 54 EP ARF Bedienungsanleitung

Hobby King

Hobby King FALCON TRAINER Bedienungsanleitung

Hobby King

Hobby King SU-35 FIGHTER Bedienungsanleitung

Hobby King

Hobby King MXS-R 64 Bedienungsanleitung

Hobby King

Hobby King Aether 3700 EP Bedienungsanleitung

Hobby King

Hobby King WARGO YAK55 Bedienungsanleitung

Hobby King

Hobby King J3 NAVY CUB Bedienungsanleitung

Hobby King

Hobby King Gulfstream G500 ARF Bedienungsanleitung

Hobby King

Hobby King Raven 990 MINI DLG 2017 Bedienungsanleitung

Hobby King

Hobby King Mariposa Trainer Bedienungsanleitung

Hobby King

Hobby King B-17 F Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung