Honeywell CL70PE Bedienungsanleitung

Portable Evaporative Air Cooler

User Manual (Web)

Read and save these instructions before use

Model:

CL70PE/ CO70PE

1) Louvers 10) Washable Mesh Filter

2) Water Level Indicator 11) Rear Grill Screw

3) Casters 12) Honeycomb Cooling Media

4) Control Panel 13) Rear Grill

5) Handle 14) Water Regulator

6) Ice Compartment Lid 15) Water Fill Door

7) Power Cord Wrap 16) Water Inlet Valve

8) Water Tank 17) Drain Plug

9) Power Cord & Plug

PARTS DESCRIPTION

WARNING -- READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER

MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY

DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS

ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER

LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL

PREVAIL.

HML0.5 124SC

MODE SPEED POWER TIMER SWING(H)

SWING(V)

USE & OPERATION

Icons on Display Screen

CONTROL PANEL

Swing

(Vertical Louvers)

Cool

Speed

Power

Timer

Swing

(Horizontal Louvers)

IMPORTANT: Honeywell Outdoor Air Cooler models are designed to IPX4 product standards and not

recommended to be placed outdoors during heavy rain or snow.

FOR OUTDOOR MODEL CO70PE:

WARNING: Use only on GFCI Protected outlets/ sockets (for USA only).

Press the TEST button (then RESET button) every month to ensure proper operation.

Power cords must be secured to avoid tripping.

The wiring and connections must be protected from water. The electrical plug and Air Cooler

connections must be dry at all times. When used outdoors, insert the air cooler electrical plug

into an IP44 compliant outdoor electrical outlet.

Set the unit on a solid ﬂat surface.

•

USE & OPERATION (CONTINUED)

POWER

Press the button to turn the unit on. The cooler will start automatically at medium speed. After a

few seconds the speed will switch to low. To turn the unit off, press the button again.

MODE

Press the button to activate evaporative cooling and/or louver swing modes.

Press the button until the “S” indicator light is illuminated on the control panel. The Vertical

Louvers will begin to move left to right automatically.

Press the button until the “C” indicator light is illuminated to activate evaporative cooling. The

water pump will operate and you will feel the cooler air after the Honeycomb Cooling Media is

completely wet.

Pressing the button until both “S” and “C” are illuminated will activate both Swing (Vertical

Louvers) and Cool modes simultaneously.

Note: When the “C” mode is not selected, the unit functions in a fan only mode, without evaporative

cooling.

FUNCTION BUTTONS

SPEED

Press the button repeatedly to change the speed between High - Medium - Low.

The indicator light will show the selected speed.

TIMER

Press the button until the desired time duration setting is selected. When the set time has passed,

the unit will automatically turn off (unit remains in Standby mode until power cord is unplugged from

electrical socket). The TIMER function allows you to program the unit for up to 7.5 hours of use.

SWING(H)

Press the button until the indicator light turns on. This activates the

Horizontal Louvers and they will begin to move up and down automatically.

LOUVER

MOVEMENT

In cooling mode, Honeywell Air Coolers provide cool, moist air through the

evaporation of water. There is a manual Water Regulator knob located behind

the ice compartment of the unit. This allows you to adjust the amount of water

pumped over the Honeycomb Cooling Media, thus helping to control cooling

and humidiﬁcation levels.

When the Water Regulator is set to MIN, the water pump distributes a minimal

amount of water to the Honeycomb Cooling Media. This results in less water

evaporation and reduces the cooling effect.

When the Water Regulator is set to MAX, the water pump distributes the maximum amount of water

to the Honeycomb Cooling Media. This results in maximum water evaporation and greater cooling

performance.

USE & OPERATION (CONTINUED)

ROOM COOLING AND HUMIDIFYING

REMOTE CONTROL

NOTE:

•

The remote control requires AAA (2 x 1.5V) batteries for replacement.

Open the battery compartment at the back of the remote control and insert the batteries inside.

Care must be taken to insert the batteries according to the correct polarity (+ / –) markings

shown inside the battery compartment.

Always point the remote control signal transmitter towards the unit when operating. Make sure

that the signal path is not obstructed.

Remove the batteries if the unit is not going to be used for an extended period of time.

Do not drop the remote control.

Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.

Do not mix old and new batteries.

Do not recharge the battery.

SWING (H)

SPEED

TIMER MODE

ON/OFF POWER :

ON / OFF

Controls the motion of the horizontal louvers

Controls the Timer function for automatic off

Controls the motion of the vertical louvers and

evaporative Cooling On / Off

Controls timer function for automatic off

SWING

TIMER

SPEED

MODE

Water Regulator

MAX

MIN

It is ideal to use the Continuous Water Supply Connection to run the unit for long periods of time

without refilling the tank. This also helps prevent pump failure in case the cooler is running with

inadequate water in the tank.

CAUTION:

Unplug the unit from the electrical power outlet before ﬁlling or emptying the water tank.

Continuous Water Supply Connection:

For a continuous water supply, you will need a garden hose that is connected to a main water supply.

Note: The garden hose is not included. Please make use of a garden hose which is compatible with

the unit connection.

FILLING WITH WATER

Locate the male connector at one end of the garden hose. Insert the garden hose connector into

the water inlet valve of the cooler. Screw and tighten the water inlet valve onto the threaded part

of the garden hose connector, making sure the hose connector is secured to ensure there will be

no leaks. If there is leakage, the hose and the water inlet valve may not be connected properly. Try

to disconnect, replace and tighten the water inlet valve again.

When the connection is secured, turn ON the water supply and the

water will ﬂow into the water tank of the cooler.

The cooler is now set so the water reﬁlls automatically.

When the water tank is full, the water inlet valve will

automatically stop the water supply from overﬂowing.

WARNING: The maximum water inlet pressure is 0.5 MPa.

•

USE & OPERATION (CONTINUED)

REMOTE CONTROL (CONTINUED)

COOLER LOCATION

•

Exhausted batteries are to be removed from the product and safely disposed of as per local

regulations.

Do not dispose of batteries in ﬁre. Batteries may explode or leak.

WARNING: Caution for ingestion of the small battery. Keep away from children and animals.

Make sure to position the air cooler correctly before you set up and start using the product.

Please refer to the COOLER LOCATION (IMPORTANT TO READ) section of the separate Safety &

Maintenance Guide.

Garden Hose

Water

Inlet Value

USE & OPERATION (CONTINUED)

FILLING WITH WATER (CONTINUED)

LOW WATER ALARM

The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the

minimum level, you will hear a beeping sound and the indicator light will ﬂash continuously. The unit

will automatically pause evaporative cooling.

Reﬁll the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and unplug

from the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and

switch ON again.

To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch the

unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low Water

Alarm will sound again if the COOL function is activated while the water tank is still empty.

Water

Fill Door

Manual Water Tank Reﬁll:

Open the Water Fill Door located on the side of the unit.

The Water Level Indicator is located at the front of the unit. Reﬁll the

water tank when water level is low. Do not ﬁll water above the "Max."

water level mark to avoid water droplets collecting on the louvers.

Check the water level in the tank before running the COOL function.

Make sure that the water in the tank is above the minimum water level

mark. Running the unit in COOL mode with inadequate water may

cause pump failure.

WARNING: Always ensure the water in the water tank is above the minimum (Min.) water level mark

for both Continuous & Manual Water Reﬁll. Running the unit in Cool mode with inadequate water

may cause pump failure.

Note: The water capacity refers to the total volume of water that can

be contained within the air cooler water tank and water distribution

system. The water capacity in the tank at the “Max.” indicator level may

be lower than the actual water capacity of the air cooler.

Note: If ice is available, you may add ice in the ice tray to enhance the

cooling performance.

WARNING: Do not ﬁll water tank with dirty water or salt water. This can damage the unit and Honeycomb

media.

Ice Tray

CLEANING & DRAINING THE WATER TANK

Move the unit to a location where the water can be drained. Remove the cap from the Drain plug

located at the bottom of the unit. Allow the tank to empty.

Reﬁll the water tank with clean water, up to the maximum level and drain it completely.

Use a damp cloth to remove the dirt and dust from the surface of the unit. Never use corrosive

elements or chemicals to clean this product.

When the product is not in use, store the unit in a dry place out of direct sunlight.

If the cooler will not be used for a long period of time, please refer to the STORAGE & MAINTENANCE

GUIDELINES located in the separate Safety & Maintenance Guide.

WARNING:

Before cleaning the unit, switch the unit OFF and disconnect from the electrical socket.

•

USE & OPERATION (CONTINUED)

CLEANING THE WASHABLE MESH FILTER AND HONEYCOMB COOLING MEDIA

The appliance is supplied with a Washable Mesh Filter and Honeycomb Cooling Media.

The Washable Mesh Filter and Honeycomb Cooling Media are located inside the Rear Grill (See

Figure 1 and 2) and see below for instructions on how to remove them from the unit for cleaning.

Do not run the unit in COOL mode with stale water in the tank. You must empty the water tank

and reﬁll with fresh water, especially if the tank has not been cleaned in a long time.

The cleaning frequency for the Honeycomb media depends on local air and water conditions.

In areas where the mineral content of water is high, mineral deposits may build up on the

Honeycomb Cooling Media and restrict air ﬂow. Draining the water tank and reﬁlling with fresh

water at least once a week will help reduce mineral deposits. If mineral deposits remain on

the Honeycomb Cooling Media, the media should be removed and washed under fresh water. The

media should be cleaned every two months or sooner, depending on your needs.

For best results allow the Honeycomb Cooling Media to dry after each use by turning off the cool

function 15 minutes before turning the unit off.

•

Slide out the Washable Mesh Filter and clean with

water.

Remove all the screws from the Rear Grill of the Air

Cooler.

Carefully pull out the rear grill from the cooler.

Carefully pull out the Honeycomb Cooling Media

from the rear grill.

There are two Horizontal Bars holding the

Honeycomb Cooling Media in place. Remove all the

screws from the Horizontal Bars and then pull the

bars off of the Honeycomb Cooling Media.

Replace or clean media with water and a damp

cloth as needed.

Removing the Washable Mesh Filter/ Honeycomb Cooling Media:

WARNING: Switch the unit OFF and disconnect from the electrical socket.

WARNING: DO NOT operate the Air Cooler when

the Rear Grill or Honeycomb Media is removed from

the Air Cooler, or if there is a loose-ﬁtting Rear Grill

or Honeycomb Cooling Media. Doing so can cause

serious injury or dangerous electrical shock.

Honeycomb

Cooling Media

Horizontal Bar

Screws

Rear Grill

Washable

Mesh

Filter

Figure 1:

Figure 2:

Andere Handbücher für CL70PE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Klimaanlage Handbücher

Honeywell

Honeywell MM14CCS Bedienungsanleitung

Honeywell

Honeywell CO25AE Bedienungsanleitung

Honeywell

Honeywell MN10CES Bedienungsanleitung

Honeywell

Honeywell CL201AE Bedienungsanleitung

Honeywell

Honeywell CO60PM Series Bedienungsanleitung

Honeywell

Honeywell HT09CESAWK Bedienungsanleitung

Honeywell

Honeywell MP10CESWW Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell HF Series Bedienungsanleitung

Honeywell

Honeywell HM12CESWK Bedienungsanleitung

Honeywell

Honeywell CL60PM Series Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell MM14CCS Bedienungsanleitung

Honeywell

Honeywell HWAC-1217S Bedienungsanleitung

Honeywell

Honeywell CL25AE Bedienungsanleitung

Honeywell

Honeywell CO301PC Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell CL20AE Bedienungsanleitung

Honeywell

Honeywell CO60PM Series Betriebsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell ES800 Bedienungsanleitung

Honeywell

Honeywell CS071AE Bedienungsanleitung

Honeywell

Honeywell CO60PM Series Bedienungsanleitung

Honeywell

Honeywell CO301PC Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung