Honeywell Genetron ST-20 Bedienungsanleitung

AC & Refrigeration Flush

Honeywell Genetron®ST-20™Flush

With the phase-out of R11, common service prac-

tice has been to purge systems with nitrogen and

rely on filter driers to clean the system instead of

flushing. Unfortunately, filter driers have limited acid

removal capacity and recommended procedures

such as acid testing and additional filter changes

are not always followed. Additionally, contaminants

downstream of the filter can cause component

damage or blockage before filtration has sufficient

cycles to remove the contaminants.

Genetron ST-20 Flush uses patented technology to

provide excellent cleaning of refrigerant and A/C

systems in a very efficient and cost effective

manner. A carefully selected boiling point assures

the solvent is easily removed from the system.

Genetron ST-20 Flush is effective for use on all

HCFC and HFC systems and is compatible with

current materials of construction including common

seals and gasket materials.

0.0

10.0

20.0

30.0

40.0

50.0

60.0

RX11®ST-20 RX11®ST-20

% Residue left

0.0

10.0

20.0

30.0

40.0

50.0

60.0

70.0

80.0

90.0

100.0

RX11®ST-20 RX11®ST-20

% Oil Removed

2minutes / 20 psig N2

5minutes / 100 psig N2

• A flushing agent with excellent solvency for mineral

and new generation refrigerant oils.

• Saves you time – offers faster cycle times than other

flushing agents.

• Made with the new HFC-245fa molecule which is fully

compatible with HFCs and HCFCs.

• Safe, odorless, and non-flammable.

• Used in the same way as R141b and R11.

• Quick drying due to its low boiling point.

• Compatible with most common construction materials

and commonly used plastics and elastomers.

• Especially valuable for systems which have

experienced compressor burnouts, new system

cleaning or retrofits.

• Formulated with SNA approved components.

• Conveniently available in pressurized packaging.

• Easily purged from components when cleaning

is complete.

Genetron ST-20 Flush for Refrigeration and Air Conditioning Systems

Genetron ST-20 Flush is… Com arison of Flush Solvent Performance

When installing a new R410A air-conditioning system to replace an existing R22 system, it

may be possible to use the existing line set. Consult the OEM’s installation manual and

determine if the line sizing is correct and proceed as follows:

1. Before starting any work put on approved safety goggles and nitrile gloves and remember

to work only in a properly ventilated area.

2. Recover the existing R22 charge; it is illegal to vent any refrigerant.

3. Disconnect any electrical power feeds to the system including any solenoids or

reversing valves.

4. Using a tubing cutter cut the liquid and suction line at both the condensing unit and

the evaporator.

5. Temporarily connect the liquid and suction lines at the evaporator using clear plastic tubing,

suitable adapters and hose clamps.

6. Using an injection tool or a compression fitting and adapters, connect a refrigeration service

hose to the suction line at the condensing unit location.

7. osition a clean container at the liquid line to catch solvent and contaminants as they are

purged from the system. urged material may include acids, oil and particulate debris

which must be disposed of properly.

8. Connect the flush can valve as shown in Figure 1 and 2 or use a valve capable of

connecting to 7/16” 28 thread. These valves are currently offered for sale at most

refrigeration and air-conditioning wholesalers.

9. Connect the refrigeration service hose or refrigeration manifold set to the can valve and the

suction line, invert the ST-20 can, open the valve and give a 15–20 second blast of ST-20

Flush. Inspect the clear tubing at the evaporator and look for liquid. If no liquid is present

continue 15 second purges until it appears. Follow ST-20 with a regulated supply of dry

nitrogen and push the solvent into the receiving container while observing the condition of

the purged material. When the solvent runs clear with no oil or contaminants present the

flushing operation is complete, follow with a dry nitrogen purge. Never pressurize the

Genetron ST-20 container. Dispose of the waste material properly.

10. Connect the line set to the new evaporator and condensing unit and evacuate and leak

check as per current guidelines.

Line Set Cleaning for Retrofitting Procedure

Figure 1 Figure 2

Disclaimer

All statements, information and data given herein are believed to be

accurate and reliable but are presented without guaranty, warranty

or responsibility of any kind, expressed or implied. Statements or

suggestions concerning possible use of our products are made

without representation or warranty that any such use is free of

patent infringement and are not recommendations to infringe any

patent. The user should not assume that all safety measures are

indicated, or that other measures may not be required.

Honeywell Genetron Refrigerants

101 Columbia Road

Morristown, NJ 07962-1053

Phone:1-800-631-8138

www.honeywell.com/genetron

Genetron is a registered trademark of Honeywell International In .

ST-20 is a trademark of Honeywell International In .

RX11-Flush is a trademark of Nu-Calgon.

Printed in U.S.A.

G525-200

System Re air and Cleanu Procedure

1. After a mechanical failure or hermetic motor burnout, use Genetron ST-20 Flush to

remove contaminants by flushing interconnecting piping as per the directions for Line

Set Cleaning.

2. Remember to disconnect all electrical connections to the system and obtain and use

safety goggles and nitrile gloves.

4. Do not attempt to push ST-20 Flush through compressor bodies.

3. It will be necessary to cut the refrigeration or air conditioning system at several points

to isolate large components such as receivers and condensers which must be cleaned

separately. It may be impractical to clean large components with ST-20 Flush. Inspect

these components and consider mechanical cleaning if large deposits are discovered.

Remove any solenoid or reversing valves from the piping. It may become necessary to

modify procedures for line set cleaning to completely flush these components, use dry

nitrogen to completely purge the component.

5. After cleaning and purging, assemble the refrigeration or AC system. Remember to

purge the system with low pressure nitrogen during brazing operations.

6. Replace the liquid line filter drier and consider installing a suction filter.

7. If the original compressor is being re-installed, change the lubricant. Use only lubricants

specified by the compressor manufacturer.

8. ressurize the system with nitrogen and leak check as per AHRI and E A guidelines.

9. Evacuate the system and charge the proper refrigerant as per the system

manufacturer’s recommendations.

10. If a retrofit was accomplished during this repair, label the system indicating the

refrigerant and lubricant used.

11. roperly dispose of contaminated Genetron ST-20 Flush.

Andere Honeywell Klimaanlage Handbücher

Honeywell

Honeywell Perfect Climate Comfort Center PC8900 Bedienungsanleitung

Honeywell

Honeywell ES800I Bedienungsanleitung

Honeywell

Honeywell MM14 Series Bedienungsanleitung

Honeywell

Honeywell MN12CES Bedienungsanleitung

Honeywell

Honeywell CL15AE Bedienungsanleitung

Honeywell

Honeywell ES800 Bedienungsanleitung

Honeywell

Honeywell CS07AE Bedienungsanleitung

Honeywell

Honeywell CS10XE Series Bedienungsanleitung

Honeywell

Honeywell CL25AE Bedienungsanleitung

Honeywell

Honeywell CL152 Bedienungsanleitung

Honeywell

Honeywell CSO71AE Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell HW4CEDAWW0 Bedienungsanleitung

Honeywell

Honeywell CS12AE Bedienungsanleitung

Honeywell

Honeywell MN4HFS0 Bedienungsanleitung

Honeywell

Honeywell HM Series Bedienungsanleitung

Honeywell

Honeywell TC09PM Bedienungsanleitung

Honeywell

Honeywell CO25AE Bedienungsanleitung

Honeywell

Honeywell TC09PEU Bedienungsanleitung

Honeywell

Honeywell HW-QUICK12E Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Honeywell

Honeywell CL151 Bedienungsanleitung

Honeywell

Honeywell CL202PEUI Bedienungsanleitung

Honeywell

Honeywell CL30XC Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung