Honeywell Thor VM3 Bedienungsanleitung

Thor™ VM3

Vehicle-Mount Computer

Quick Start Guide

Aller à www.honeywellaidc.com pour le français.

Vai a www.honeywellaidc.com per l'italiano.

Gehe zu www.honeywellaidc.com für Deutsch.

Ir a www.honeywellaidc.com para español.

Para Português, acesse www.honeywellaidc.com.

Перейти на русскоязычный сайт www.honeywellaidc.com.

Pro češtinu jdi na www.honeywellaidc.com.

Pre slovenčinu choďna www.honeywellaidc.com.

Türkçe için lütfen www.honeywellaidc.com sayfasını ziyaret ediniz.

Idźna stronę: www.honeywellaidc.com po quick start w języku polskim.

如要到中国 www.honeywellaidc.com（简体）。

www.honeywellaidc.com

VM3-QS Rev B

6/15

Components - Front

P1 P14

P13

P12

P11

P10

System

LEDs

Power

Button

Connection

LEDs

Components - Rear

See the Thor VM3 User’s Guide for dock fuse replacement in-

structions.

Fuse Power

Switch

Power

Cable

Connector

I/O Connectors:

CANbus/Audio

COM2

COM1

USB1

USB2

Dock

Release

Ethernet USB Host

Mount to Vehicle

The Thor VM3 should be secured to an area in the vehicle where it:

• Does not obstruct the driver's vision or safe vehicle operation.

• Will be protected from rain or inclement weather.

• Will be protected from extremely high concentrations of dust or

wind-blown debris.

• Can be easily accessed by a user seated in the driver's seat while

the vehicle is not in operation.

To mount the Thor VM3 using a RAM mount system:

1. Attach RAM base to vehicle (RAM ball, RAM Clamp, RAM Plate,

etc.).

2. Attach RAM ball and optional keyboard bracket to the Smart

Dock.

3. Attach Thor VM3 assembly to RAM base using RAM arm and

tighten knob on RAM arm.

4. If using keyboard bracket, attack keyboard to mounting plate.

5. Attach keyboard assembly to Thor VM3 assembly using RAM

arm and tighten knob on RAM arm.

Note: An external keyboard is required for initial setup.

For more details and other mounting options, refer to the Thor VM3

User’s Guide available at www.honeywellaidc.com.

Connect Accessories

Connect serial accessories, such as a bar code scanner, to the

COM1 or COM2 port on the Smart Dock.

Connect the optional VMT keyboard to the USB1 port on the Smart

Dock.

Connect other USB accessories to the optional VM3052CABLE

adapter cable which attaches to the USB2 port.

Connect Power

The Thor VM3 can be connected to vehicle power as follows:

• Direct power connection (12-48VDC vehicles). See Connecting

the Power Cable, below.

• Replace a previously installed VX6/VX7 or Thor VX8/VX9 with an

adapter cable. See the Thor VM3 User’s Guide, available at

www.honeywellaidc.com.

• High voltage forklifts (over 60V). Refer to the Thor VM3 User’s

Guide available at www.honeywellaidc.com.

Connecting the Power Cable

The following power option is for 12-48VDC vehicles (10-60VDC

direct connection).

• Route the power cable away from the outside of the forklift.

• Choose a mounting location so that the power cable does not

extend outside the vehicle and that provides sufficient clearance

so that the power cable (especially the dock connector end) is not

pressed against part of the vehicle.

• Regularly inspect power cable for damage, especially in low

temperature environments.

CAUTION - For installation by trained service personnel only.

Fuse Requirements

WARNING - For proper and safe installation, the input power

cable must be connected to a fused circuit on the vehicle. If

the supply connection is made directly to the battery, the fuse

should be installed in the positive lead within 5 inches of the

battery’s positive (+) terminal. Use VM3055FUSE (or equiva-

lent) to install the fuse as shown below:

• F o r 12VDC input, use the 10A fuse from the kit or a slow

blow fuse that has a DC voltage rating greater than 12VDC.

• F o r 24VDC input, use the 6A fuse from the kit or a slow

blow fuse that has a DC voltage rating greater than 24VDC.

• F o r 36VDC input, use the 4A fuse from the kit or a slow

blow fuse that has a DC voltage rating greater than 36VDC.

• F o r 48VDC input, use the 3A fuse from the kit or a slow

blow fuse that has a DC voltage rating greater than 48VDC.

Note: For North America, a UL Listed fuse is to be used

Power Cable Routing

Power Cable Information

Twist the red and red/white wires together and twist the black

and black/white wires together before connecting to vehicle

power.

Connect the green wire to vehicle ground:

Power Cable Installation

1. The Thor VM3 must not be mounted in the Smart Dock.

The power switch on the dock must be turned Off. The

power cable must be UNPLUGGED from the dock.

2. Install the VM3 fuse kit (or equivalent slow blow fuse) within

5” (12.7 cm) of the vehicle battery (if using unswitched

power). Refer to the installation instructions included with

the fuse kit or Fuse Requirements earlier in this document.

3. The cable is rated for a maximum temperature of 221°F

(105°C). The cable should be protected from surfaces that

For battery powered vehicles:

The green wire must be connected to the vehicle chassis

ground.

For internal combustion engine powered vehicles:

The green wire is connected to the vehicle chassis

ground, which can also be battery negative.

Wire Color Connection

Red DC + (10-60 VDC)

Red/White DC + (10-60 VDC)

Black DC -

Black/White DC -

Green Ground

Blue Ignition Input (optional)

Refer to the Thor VM3 User’s Guide, avail-

able at www.honeywellaidc.com, for further

information about ignition control.

exceed this temperature, from physical damage from

moving parts, and from chemicals or oil that cause the

insulation to deteriorate.

4. Avoid sharp bends. The power cable is less flexible in low

temperature environments.

5. Route the cable the shortest way possible removing any

leftover cable, making sure the cable does not interfere with

safe operation and maintenance of the vehicle.

6. Secure the cable to the vehicle structure at approximately

one foot intervals, taking care not to over tighten, pinch

conductors, or penetrate the insulation.

7. Use proper electrical and mechanical fastening means for

terminating the cable. Properly sized “crimp” type electrical

terminals are an accepted method of termination. Select

electrical connectors sized for use with 20AWG (0.81mm2)

conductors.

8. Connect the watertight connector end of the power cable to

the Smart Dock power connector by aligning the connector

pins to the power connector; push down on the watertight

connector and twist it to fasten securely.

9. Secure the power cable to the dock using strain relief cable

clamps, and place the Thor VM3 in the dock.

10. If using the Screen Blanking feature, install the screen

blanking box or switch. (Refer to the installation

instructions that came with the Screen Blanking box, or to

the Thor VM3 User’s Guide, available at

www.honeywellaidc.com for further information.)

11. Move the power switch on the back of the dock to the on

position.

12. Press the power button on the front of the Thor VM3.

Setting up the Thor VM3 Software

Note: Have the following information available before setting up

your Thor VM3:

•Network ID (SSID) of the Access Point

•Wireless network authentication credentials

1. Connect the Thor VM3 to an external power source.

2. Press the Power button.

3. Attach a USB keyboard during the setup process.

4. Accept the EULA.

5. Calibrate the touch screen (resistive touch screen only, not

applicable to PCAP touch screen).

6. Set the date and time.

7. Edit the radio parameters.

8. Edit Enterprise Control Panel settings (i.e.: Bluetooth Scanning,

Enterprise Settings, etc.).

9. Edit the RFTerm or Enterprise TE Terminal Emulation

parameters (optional).

10. Perform a reboot.

Bluetooth

Refer to the Thor VM3 User’s Guide, available at

www.honeywellaidc.com, for information when using the Thor VM3

with Bluetooth.

Andere Handbücher für Thor VM3

Inhaltsverzeichnis

Andere Honeywell Autozubehör Handbücher

Honeywell

Honeywell Thor VM2W Bedienungsanleitung

Honeywell

Honeywell Thor VM2 Bedienungsanleitung

Honeywell

Honeywell THOR VM1 Bedienungsanleitung

Honeywell

Honeywell Thor VM2 Bedienungsanleitung

Honeywell

Honeywell Thor VM3 Bedienungsanleitung

Honeywell

Honeywell TCVT2 Bedienungsanleitung

Honeywell

Honeywell Thor VM1A Bedienungsanleitung

Honeywell

Honeywell THOR VM1 Bedienungsanleitung

Honeywell

Honeywell VX3Plus Bedienungsanleitung

Honeywell

Honeywell Intermec AE36 Bedienungsanleitung

Honeywell

Honeywell Thor VM1 W Bedienungsanleitung

Honeywell

Honeywell Thor VM2WG Bedienungsanleitung

Honeywell

Honeywell Thor CV31 Bedienungsanleitung

Honeywell

Honeywell Thor VM2 Bedienungsanleitung

Honeywell

Honeywell VX6 Bedienungsanleitung

Honeywell

Honeywell Thor VM2C Bedienungsanleitung

Honeywell

Honeywell THOR VM1 Bedienungsanleitung

Honeywell

Honeywell Thor VM2 Bedienungsanleitung

Honeywell

Honeywell THOR VM1 Bedienungsanleitung

Honeywell

Honeywell Thor VM2 Bedienungsanleitung

Honeywell

Honeywell Thor CV41 Bedienungsanleitung

Honeywell

Honeywell Thor CV31 Bedienungsanleitung

Honeywell

Honeywell THOR VM1 Bedienungsanleitung

Honeywell

Honeywell KMH 880 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung