Honeywell MS5145 - 00 Bedienungsanleitung

Introduction

Product Overview

The MS5145 Eclipse is a single-line, hand-held laser scanner.

Equipped with Honeywell’s patented CodeGate® technology,

Eclipse can be used in a wide variety of applications. CodeGate

technology allows the user toeasily target the desired bar code

and complete the data transmission with a simple press of a

button. This combination makes Eclipse a perfect selection for

menu scanning, point-of-sale, document processing and inventory

control.

With state-of-the-art scanning technology embedded inside, the

MS5145 Eclipse has a longer working range and a wider scan field

than a typical CCD. The width of the scan line grows as the

scanner moves further away from bar codes. In addition, the laser

beam pulses, making lining up bar codes easy and when the

scanner senses a bar code (CodeSense® Mode), the laser beam

automatically switches to scan mode and activates CodeGate to

ensure high-speed scanning and accuracy.

Many standard features are included such as: user configurable

Flash ROM, PowerLink user-replaceable cables, MetroSet®2 and

MetroSelect® configuration, and data editing (parsing).

Model Number Interface

MS5145 – 00 Laser Emulation

MS5145 – 11 RS485 , RS232-TXD, RXD, RTS, CTS

MS5145 – 14 RS232 - TXD, RXD, RTS, CTS, DTR, DSR

MS5145 – 38

TTL RS232 Low Speed USB,

Keyboard Emulation or Serial Emulation*

MS5145 – 40 Full Speed USB

MS5145 – 41 RS232/Light Pen Emulation

MS5145 – 47

Keyboard Wedge, Stand Alone Keyboard and TTL RS232

Transmit/Receive

Configurable for Keyboard Emulation Mode or Serial Emulation Mode. The default

setting is Keyboard Emulation Mode.

◈

Applicable for IBM® Host applications. Applicable for IBM® Host applications.

MS5145 Components

Item No. Description

Mode Select Button/CodeGate Button(see page 13)

2 Red LED

(see page 15)

3 Greed LED

(see page 15)

Pin Hole for Cable Release

(see page 6)

5 Red Output Window (Laser Aperture)

6 Speaker

(see page 14)

10-Pin RJ45, Female Socket

(see page31)

Figure 1.Scanner Components

Maintenance

Smudges and dirt on the unit’s window can interfere with the

unit’s performance. If the window requires cleaning, use only a

mild glass cleaner containing no ammonia. When cleaning the

window, spray the cleaner onto a lint free, non-abrasive cleaning

cloth then gently wipe the window clean.

If the unit’s case requires cleaning, use a mild cleaning agent that

does not contain strong oxidizing chemicals. Strong cleaning

agents may discolor ordamage the unit’s exterior.

Caution and Serial Number Labels

Figure 2. Label Location on the Bottom of the Scanner with Example

Caution: To maintain compliance with applicable standards, all circuits connected

to the imager must meet the requirements for SELV (Safety Extra Low

Voltage) according to EN/IEC 60950-1.

To maintain compliance with standard CSA C22.2 No. 60950-1/UL

60950-1 and norm EN/IEC 60950-1, the power source should meet

applicable performance requirem

ents for a limited power source.

Cable Installation and Removal

Installation

1. Insert the cable’s modular connector into the socket on the

scanner.

2. Pull gently on the cable strain relief to ensure the cable is

installed.

Note: If the PowerLink cable is not fully latched, the unit can

power intermittently.

Figure 3.

Removal

Disconnect the power supply from the PowerLink cable and turn

off power to the host system before removing the cable from the

scanner.

1. Locate the small ’pin-hole’ on the

front side of the scanner near the

end of the handle.

2. Bend an ordinary paperclip into the

shape shown.

3. Insert the paperclip (or other small

metallic pin) into the small ’pin-hole’.

There will be a faint ’click’ when the

connector’s lock releases.

4. Pull gently on the cable’s strain-relief

to remove the cable.

Figure 4.

Installation

RS232, Light Pen or Laser Emulation

1. Turn off the host system.

2.Plug the male, 10-pin RJ45 end of the

PowerLink cable into the 10-pin socket

on the MS5145.

3. Connect the 9-pin female end of the

PowerLink cable to the appropriate

communication port on the host device.

4. Plug the external power supply into the

power jack on the PowerLink cable.

5. Check the AC input requirements of the

power supply to make sure eth voltage

matches the AC outlet. The outlet must

be located near the equipment.

6. Connect AC power to the transformer.

7. Turn on the host system.

Figure 5. RS232, Light Pen, or

Laser Emulation

Installation Notes

Plugging the scanner into the serial port of the PC

does not guarantee that scanned information will

appear at the PC. A software driver and correct

configuration settings are also required for proper

communications to occur.

Powering the MS5145 directly from the host device

can sometimes cause interference with the operation

of the scanner or the computer. Not all computers

supply the same current. For this reason, using an

external power supply is recommended. For additional

information, contact a customer service representative.

All MS5145-00 scanners leave the factory with the

Laser Emulation Mode enabled. If recall defaults is

scanned while re-configuring the scanner the Laser

Emulation Mode will no longer be enabled. Refer to

the MS5145-00 Laser Emulation Mode section of the

MetroSelect Single-Line Configuration Guide for in-

formation on enabling the Laser Emulation Mode.

See caution on page 5.

Keyboard Wedge

1. Turn off the host system.

2. Plug the male, 10-pin RJ45

end of the PowerLink cable

into the 10-pin socket on the

MS5145.

3. Disconnect the keyboard

from the host/PC.

4. Connect the Y ends of the

PowerLink cable to the key-

board and the host’s

keyboard port. If necessary,

use the supplied adapter

cable to make the

connections.

5. Plug the external power

supply into the power jack

on the Power Link cable.

6. Check the AC input require-

ments of the power supply

to make sure the voltage

Figure 7. Keyboard Wedge

matches the AC outlet. The

outlet must be located near

the equipment

7. Connect AC power to the transformer.

8. Turn on the host system.

Installation Note

Powering the MS5145-47 directly from the computer

can sometimes cause interference with the operation

of the scanner or the computer. Not all computers supply

the same current through the keyboard port, explaining

why a scanner may work on one computer and not

another. Contact a customer service representative if an

external power supply is required.

See caution on page 5.

Stand-Alone Keyboard

1. Turn off the host system.

2. Connect the 10-pin RJ45 male

connector into the jack on the Eclipse.

There will be a ’click’ when the

connection is made.

3. Connect the L-shaped plug of the

power supply into the power jack on

the PowerLink cable.

4. Make sure the AC input requirements

of the power supply match the AC

outlet. Connect the power supply into

an AC outlet. The outlet should be

near the equipment and easily

accessible.

5. Connect the PowerLink cable to the

keyboard port on the host system.

6. Turn on the host system.

Figure 8. Stand-Alone Keyboard

Installation Note

Powering the MS5145-47 directly from the computer can

sometimes cause interference with the operation of the

scanner or the computer. Not all computers supply the

same current through the keyboard port, explaining why

a scanner may work on one computer and not another.

Contact a customer service representative if an external

power supply is required.

See caution on page 5.

USB: Low Speed USB (-38)

Full Speed USB (-40)

1. Turn off the host system.

2. Connect the 10-pin RJ45

male connector of the USB

cable into the jack on the

Eclipse. There will be a ’click’

when the connection is made.

3. Connect the other end of the

USB cable to the host USB port.

4. Turn on the host system.

Figure 9. USB

Installation Notes

As a default, the MS5145-38 leaves the factory with

USB Keyboard Emulation Mode enabled.

For information on configuring the MS5145-38 for

USB Serial Emulation Mode, please refer to the USB

section of the MetroSelect Single-Line Configuration

Guide..

Plugging the scanner into a port on the host system

does not guarantee that scanned information will be

communicated properly to the host system. All

Eclipse’s are shipped already configured with a set of

factory defaults. Please refer to the MetroSelect

Single-Line Configuration Guide or MetroSet2’s help

files for instructions on changing the scanner’s factory

default configuration. The scanner and host system

must use the same communication protocols.

See caution on page 5.

Scanner Operation

Modes of Operation

CodeGate®, Out-of-Stand

CodeGate activates when removed from the stand

Bar code data is transmitted when the button is

pressed

Manual Activation Mode*, Out-of-Stand

Button activates laser

Bar code data is scanned and transmitted while

button is held down

Figure 10. CodeGate Enabled Figure 11. Manual Activation Mode

Depth of Field by Bar Code Element Width

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Barcode-Lesegerät Handbücher

Honeywell

Honeywell MS1890 Focus Bedienungsanleitung

Honeywell

Honeywell QUANTUME IS3480 Bedienungsanleitung

Honeywell

Honeywell 3800r Bedienungsanleitung

Honeywell

Honeywell Captuvo SL22 Bedienungsanleitung

Honeywell

Honeywell Voyager 1602g Bedienungsanleitung

Honeywell

Honeywell MX7 Tecton Bedienungsanleitung

Honeywell

Honeywell MS9535-5 Bedienungsanleitung

Honeywell

Honeywell Eclipse MS5100 Series Bedienungsanleitung

Honeywell

Honeywell 3800G14E Bedienungsanleitung

Honeywell

Honeywell Vuquest 3310g Bedienungsanleitung

Honeywell

Honeywell 4800i Bedienungsanleitung

Honeywell

Honeywell MS4980 Bedienungsanleitung

Honeywell

Honeywell Vuquest 3310g Bedienungsanleitung

Honeywell

Honeywell Xenon 1900H Bedienungsanleitung

Honeywell

Honeywell Dolphin 7600 Bedienungsanleitung

Honeywell

Honeywell 3800 Linear Series Bedienungsanleitung

Honeywell

Honeywell MK3780-71A38 Bedienungsanleitung

Honeywell

Honeywell VoyagerCG MS9540 Handbuch

Honeywell

Honeywell Hyperion 1300G Bedienungsanleitung

Honeywell

Honeywell 3820 Bedienungsanleitung

Honeywell

Honeywell IT3800 Bedienungsanleitung

Honeywell

Honeywell Captuvo SL22 Bedienungsanleitung

Honeywell

Honeywell MK9535-79A540 - MS9535 VoyagerBT - Wireless Portable Barcode... Bedienungsanleitung

Honeywell

Honeywell Xenon XP 1950h Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung