Honeywell 4600g Bedienungsanleitung

4600g, 4600r, 4600rp, 4800i

Quick Start Guide

Note: Refer to your user’s guide for information

about cleaning your device.

For localized language versions of this document,

go to www.honeywell.com/aidc.

Getting Started

Turn off computer’s power before connecting the

scanner, then power up the computer once the

scanner is fully connected.

USB Connection

Keyboard Wedge Connection

Serial (RS-232) Connection

Reading Techniques

The view finder

projects an aiming

beam that should

be centered over

the barcode, but

can be positioned

in any direction for

a good read.

Hold the scanner

over the barcode,

pull the trigger, and center the aiming beam on the

barcode.

The aiming beam is smaller when the scanner is

closer to the code and larger when it is farther from

the code. Hold the scanner close to smaller

barcodes, and farther away from large barcodes to

get a proper read.

If the barcode is highly reflective (e.g., laminated),

you may need to tilt the scanner at an angle so the

barcode can be scanned.

Standard Product Defaults

The following barcode resets all standard product

default settings.

Standard Product Defaults

Interface

Scan the barcode that describes the PC or interface

you are using.

AT/PS2 Keyboard Wedge

(Default)

RS-232

USB Keyboard (PC)

Emulate External Keyboard

Japan DOS/V

USB Japanese Keyboard (PC)

Keyboard Country

Scan the Program Keyboard Country barcode

below, then scan the numeric barcode(s) from

page 10, then the Save barcode to program the

keyboard for your country. As a general rule, the

following characters are not supported by the

scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~.

Note: For a complete list of country codes, see the

User’s Guide for your product at our website,

www.honeywell.com/aidc.

Country Code Scan Country Code Scan

Belgium 1Italy 5

Denmark 8Norway 9

Finland 2Spain 10

France 3Switzerland 6

Germany/Austria 4USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

Trigger

The following barcodes will allow you to use the

reader in Manual Trigger mode (need to press the

trigger to read) or Presentation mode (the reader is

activated when it “sees” a barcode).

Streaming Presentation™

Note: Streaming Presentation Mode applies only

to units with the Advanced Illumination

feature. Units with the advanced illumination

feature have a software revision of

31205480-118 or newer.

When in Streaming Presentation mode, the imager

leaves the scan illumination on all the time and

continuously searches for barcodes.

Manual Trigger

(Default)

Presentation Mode

Streaming Presentation Mode

Reread Delay

This sets the time period before the scanner can

read the

same

barcode a second time. Setting a

reread delay protects against accidental rereads of

the same barcode.

Suffix

If you want a carriage return after the barcode, scan

the Add CR Suffix barcode. To add a tab after the

barcode, scan the Add Tab Suffix barcode.

Otherwise, scan the Remove Suffix barcode to

remove the suffixes.

Medium Reread Delay

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix to all Symbologies

Scan the following barcode if you wish to add a

Code ID prefix to all symbologies at once.

Note: For a complete list of Code IDs, see the

User’s Guide for your product at our website,

www.honeywell.com/aidc.

Function Code Transmit

When this selection is enabled and function codes

are contained within the scanned data, the imager

transmits the function code to the terminal. Charts

of these function codes are provided in your User’s

Guide. When the imager is in keyboard wedge

mode, the scan code is converted to a key code

before it is transmitted.

Add Code ID Prefix To All Symbologies

(Temporary)

Enable

(Default)

Disable

Data Format Editor Instructions

The following are abbreviated instructions for

entering a data format. For complete instructions

refer to your User’s Guide, available at our website,

www.honeywell.com/aidc.

1. Scan the Enter Data Format symbol.

2. Primary/Alternate Format: scan 0for Primary

Format

3. Terminal Type: scan 099 for any terminal type

4. Code I.D.: scan 99 for any barcode type

5. Length: scan 9999 for any length barcode.

6. Editor commands: use the Programming Chart

that follows.

7. Scan Save to save your entries.

Enter Data Format

Clear All Data Formats

Save

Andere Handbücher für 4600g

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Barcode-Lesegerät Handbücher

Honeywell

Honeywell MS5145 - 00 Bedienungsanleitung

Honeywell

Honeywell Fusion MS3780 Bedienungsanleitung

Honeywell

Honeywell 8600 Bedienungsanleitung

Honeywell

Honeywell Voyager 1602g Bedienungsanleitung

Honeywell

Honeywell VoyagerCG MS9540 Handbuch

Honeywell

Honeywell Xenon 1900H Bedienungsanleitung

Honeywell

Honeywell MS9520 Voyager Bedienungsanleitung

Honeywell

Honeywell MS4980 Bedienungsanleitung

Honeywell

Honeywell 5010 Bedienungsanleitung

Honeywell

Honeywell Voyager 1202G Bedienungsanleitung

Honeywell

Honeywell HH1800 Bedienungsanleitung

Honeywell

Honeywell Voyager 1450g Series Bedienungsanleitung

Honeywell

Honeywell Captuvo SL22 Bedienungsanleitung

Honeywell

Honeywell QUANTUME IS3480 Bedienungsanleitung

Honeywell

Honeywell Hyperion 1300G Bedienungsanleitung

Honeywell

Honeywell VoyagerGS 9590 Series Bedienungsanleitung

Honeywell

Honeywell 1400gPDF Bedienungsanleitung

Honeywell

Honeywell IT3800 Bedienungsanleitung

Honeywell

Honeywell Voyager 9520/40 Bedienungsanleitung

Honeywell

Honeywell YJ HF600 Bedienungsanleitung

Honeywell

Honeywell VOYAGER 1200G Bedienungsanleitung

Honeywell

Honeywell Eclipse MS5100 Series Bedienungsanleitung

Honeywell

Honeywell Solaris MS7820 Bedienungsanleitung

Honeywell

Honeywell N431X Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung