Honeywell PX4-6IE-CUTR-IG-1 Bedienungsanleitung

Cutter Kit

For PX4ie, PX6ie

Installation Guide

PX4-6IE-CUTR-IG-1 Rev A

01/20

PX4ie and PX6ie Cutter Kit Installation Guide 1

Introduction

The PX4ie and PX6ie printers can easily be fitted with an optional cutter,

provided the printer is not already fitted with a label-taken sensor. The cutters

are almost identical with exception for the width.

The cutter unit is fitted by replacing the front door and the printer hinges, and

is connected by a single cable to the DIN-connector on the printer’s front.

The cutter is available both as a factory-installed option and as a field

installable upgrading kit. It can be installed by the operator.

The cutter is intended to cut through a continuous non-adhesive paper strip or

the backing paper between labels. The cutter is not intended to cut through any

kind of adhesive or other soft material.

Adhesive material can stick to the cutting parts and render the cutter inopera-

ble and possibly damage the electric motor due to overheating

The cutter is intended to cut through continuous non-adhesive paper strip or

through the backing paper between labels. It must not be used to cut through

any kind of adhsesive or other soft material, that may stick to the cutting parts

and render the cutter inoperable and even damage the electric motor by

overheating.

Maximum paper thickness is 175

(≈ 175 grams/m

) for normal paper-based

materials.

Minimum practical copy length is 38.1mm (1.5 inches).

The cutter increases the printer’s total weight and length as follows:

The cutter can be tilted forward in order to facilitate cleaning and paper load.

Caution: Adhesive material can stick to the cutting parts and render

the cutter inoperable and possibly damage the electric

motor due to overheating.

Printer Weight Length

PX4ie 1.0 kg (2.2lbs) 28mm (1.1 inches)

PX6ie 1.65 kg (3.6lbs) 28mm (1.1 inches)

Warning: The cutting edge will rotate to home position when the

power is turned on and when the printer is rebooted. Always

keep the cutter unit closed during operation.

2 PX4ie and PX6ie Cutter Kit Installation Guide

Contents

The cutter kit consists the following,

• Cutter unit

• Two hinges with torx wrench

Installing the Cutter Kit

Follow the procedure to physically install the cutter.

Note: This procedure applies to both the PX4ie and PX6ie Printers. For simplicity,

the PX4ie Printer is depicted in the illustrations.

1. Switch off the power and disconnect the power cord.

2. Open the printer’s front door.

3. Hold the printer firmly and press the front door sideways to the left so as to

disengage the hinges.

4. Remove the door completely.

Warning: Make sure to turn off the power before beginning to install

or remove the cutter unit.

Press sideways

PX4ie and PX6ie Cutter Kit Installation Guide 3

5. Remove the existing two hinges held by four #T10 Torx screw at the bottom

of the printer.

6. Replace the hinges with the new ones that came with the cutter unit using

the same four #T10 Torx screw.

7. Fit the cutter unit to the vacant hinges. Make sure that the locking plate

snaps into the groove of the right-hand hinge and that the angled plate at

the bottom of the cutter is inserted under the printer’s bottom plate.

4 PX4ie and PX6ie Cutter Kit Installation Guide

8. Fit the cable from the cutter unit into the DIN connector on the printer’s

front.

9. Tilt the cutter unit upwards until it locks into place. If the cutter does not

lock properly, the hinges of the cutter unit may need to be adjusted using a

#T10 Torx screwdriver.

10. Plug the printer back in and switch on the power. The cutter will perform an

idle cycle in order to occupy its home position.

11. Switch off the power. Tilt down the cutter and route the paper through the

cutter unit between the guide plates (also see the User’s Guide). Then tilt

up the cutter again and lock it in closed position.

12. Check that the printhead is lowered and switch on the power. Now the

printer is ready for operation.

Press sideways

PX4ie and PX6ie Cutter Kit Installation Guide 5

Cutter for PX4ie Printer

Cutter Installed PX4ie Printer

6 PX4ie and PX6ie Cutter Kit Installation Guide

Cutter for PX6ie Printer

Cutter Installed PX6ie Printer

PX4ie and PX6ie Cutter Kit Installation Guide 7

Controlling the Cutter

The cutter can be controlled using the printer command languages and the

supported printer command languages are,

• Fingerprint

• Direct Protocol (DP)

• Intermec Printer Language (IPL)

• Datamax Printer Language (DPL)

• Zebra Simulator (ZSim)

To learn how the cutter is controlled using the printer languages, refer to the

respective command reference manual.

Maintenance and Troubleshooting

This section describes how to maintain and troubleshoot the cutter unit.

Cleaning

The cutter mechanism becomes accessible when the cover is opened. The

cutter shears will need to be cleaned on a regular basis to ensure optimal

cutting performance.

Use isopropyl to clean the cutter. Be careful to not dissolve the cutter

lubrication.

Do not force the spring-loaded anvil blade open more that 5-10mm

(0.2-0.4 inches), or the spring may be damaged.

Warning: Switch off the power or disconnect the cutter before

cleaning. Keep fingers away from cutting parts!

Caution: Isopropyl alcohol is a highly flammable, moderately toxic,

and mildly irritating substance.

8 PX4ie and PX6ie Cutter Kit Installation Guide

Troubleshooting

Use this table to understand and troubleshoot some common errors you may

receive and how to fix them.

Error, Probable cause, and Solution

Error Alert Probable Cause Solution

Error 1701

“Cutter Jammed”

A cut has been performed but

the shear has stopped on its

way back to home (bottom)

position.

Clean the shears

from adhesive

residue.

Error 37

“Cutter device not

found”

Cutter cable came loose from

DIN connector

Reconnect cutter

cable connector to

DIN connector

Error 1059

“Cutter does not

respond”

Cutter cable came loose from

DIN connector

Reconnect cutter

cable connector to

DIN connector

PX4ie and PX6ie Cutter Kit Installation Guide 9

Support

To search our knowledge base for a solution or to log into the Technical Support

portal and report a problem, go to www.hsmcontactsupport.com.

Documentation

Product documentation is available at www.honeywellaidc.com.

Limited Warranty

For warranty information, go to www.honeywellaidc.com and click Resources >

Product Warranty.

Patents

For patent information, see www.hsmpats.com.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in

specifications and other information contained in this document without prior

notice, and the reader should in all cases consult HII to determine whether any

such changes have been made. The information in this publication does not

represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the

furnishing, performance, or use of this material. HII disclaims all responsibility

for the selection and use of software and/or hardware to achieve intended

results.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated into another language without the prior written

consent of HII.

Inhaltsverzeichnis

Andere Honeywell Barcode-Lesegerät Handbücher

Honeywell

Honeywell Xenon XP 1950h Bedienungsanleitung

Honeywell

Honeywell 8680i Series Bedienungsanleitung

Honeywell

Honeywell IT3800 Bedienungsanleitung

Honeywell

Honeywell 2020-5 Bedienungsanleitung

Honeywell

Honeywell VOYAGER 1250G Bedienungsanleitung

Honeywell

Honeywell CM4680 Bedienungsanleitung

Honeywell

Honeywell Solaris MS7820 Bedienungsanleitung

Honeywell

Honeywell 8670 Bedienungsanleitung

Honeywell

Honeywell YJ-HF5000 Bedienungsanleitung

Honeywell

Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Bedienungsanleitung

Honeywell

Honeywell N431X Bedienungsanleitung

Honeywell

Honeywell Xenon XP 195 Series Bedienungsanleitung

Honeywell

Honeywell VOYAGER 1250G Bedienungsanleitung

Honeywell

Honeywell MK3480-30B104 - IS3480 QuantumE - Wired Desktop Barcode... Bedienungsanleitung

Honeywell

Honeywell Xenon 1910 Bedienungsanleitung

Honeywell

Honeywell XENON 1902 Bedienungsanleitung

Honeywell

Honeywell Genesis 7580G Technisches Datenblatt

Honeywell

Honeywell VoyagerGS MS9590i Bedienungsanleitung

Honeywell

Honeywell Quantum T 3580 Bedienungsanleitung

Honeywell

Honeywell VoyagerCG MS9540 Bedienungsanleitung

Honeywell

Honeywell Orbit MS7120 Bedienungsanleitung

Honeywell

Honeywell Voyager 9520 Bedienungsanleitung

Honeywell

Honeywell 8600 Bedienungsanleitung

Honeywell

Honeywell MS1890 Focus Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

Atid

Atid AT188N Plus Bedienungsanleitung

AZENTA

AZENTA 281947 Bedienungsanleitung