Honeywell VOYAGER 1200G Bedienungsanleitung

™

Voyager™ 1200g

Single-Line Laser Scanner

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in speci-

fications and other information contained in this document without prior notice,

and the reader should in all cases consult HII to determine whether any such

changes have been made. The information in this publication does not repre-

sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnish-

ing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, repro-

duced, or translated into another language without the prior written consent of

HII.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Web Address: www.honeywellaidc.com

Microsoft® Windows® and the Windows logo are trademarks or registered

trademarks of Microsoft Corporation.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Product Agency Compliance

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for

help.

If necessary, the user should consult the dealer or an experienced radio/

television technician for additional suggestions. The user may find the fol-

lowing booklet helpful: “Something About Interference.” This is available at

FCC local regional offices. Honeywell is not responsible for any radio or

television interference caused by unauthorized modifications of this equip-

ment or the substitution or attachment of connecting cables and equipment

other than those specified by Honeywell. The correction is the responsibil-

ity of the user.

Use only shielded data cables with this system. This unit has been tested

with cables less than 3 meters. Cables greater than 3 meters may not meet

class B performance.

Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell may void the FCC authorization to oper-

ate this equipment.

UL Statement

UL listed: UL60950-1, 2nd Edition.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Opera-

tion is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe A est conforme à la norme NMB-003

du Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

cUL Statement

cUL listed: CSA C22.2 No.60950-1-07, 2nd Edition.

Europe

The CE marking indicates compliance to 2004/108/EC EMC Directive

with Standards EN55022 CLASS B, EN55024, EN61000-3-2,

EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage Direc-

tive, when shipped with recommended power supply.

For further information please contact:

Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Honeywell International Inc. shall not be liable for use of our product with

equipment (i.e., power supplies, personal computers, etc.) that is not CE

marked and does not comply with the Low Voltage Directive.

Waste Electrical and Electronic Equipment

Information

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PAR-

LIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical

and electronic equipment (WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health

and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to

use the appropriate take-back systems for product disposal. Those sys-

tems will reuse or recycle most of the materials of the product you are dis-

posing in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you to

use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling sys-

tems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environ-

mental performances of this product.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548

Mexico

Conforms to NOM-019.

Russia

Gost-R certificate

South Korea

BSMI Standard: CNS13438, CNS 14336

International

Laser Safety Statement

This device has been tested in accordance with and complies with

IEC60825-1 ed2.0 and 21 CFR 1040.10 and 1040.11, except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PROD-

UCT, 1.0 mW MAX OUTPUT: 630-650nM.

Scanner Laser Beam

Wavelength 645 - 660 nm

Divergence < 1.5 mrad. per IEC 60825-1 worst case

Max power output < 1mw

Embedded Laser

Wavelength 645- 660 nm

Divergence < 1.5 mrad, per IEC 60825-1 worst case

Max power output < 10 mw

Caution: Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

LED Safety Statement

LEDs have been tested and classified as “EXEMPT RISK GROUP” to the

standard: IEC 62471:2006.

CB Scheme

Certified to CB Scheme IEC60950-1, Second Edition.

Solids and Water Protection

The Voyager 1200g has a rating of IP42, immunity of foreign particles and drip-

ping water.

Patents

For patent information, please refer to www.honeywellaidc.com/patents.

LASER LIGHT: DO NOT STARE INTO

BEAM. CLASS 2 LASER PRODUCT.

LASERSTRAHLUNG: NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2.

LUMIERE LASER: NE PAS REGARDER

DANS LE FAISCEAU. APPAREIL A LASER.

DE CLASSE 2 630-650nm, 1mW.

Required Safety Label Locations

Patent information-See Manual.

CC and ICES-003 information-See Manual.

Warranty VOID if case opened.

Contains no user serviceable components.

Complies with 21 CFR 1040.10 & 1040.11

except for deviations pursuant to Laser

Notice No.50,dated July 24, 2007

IEC 60825-1: 2007

94J8 I.T.E.

’

Laser Output

LASER LIGHT: DO NOT STARE INTO

BEAM. CLASS 2 LASER PRODUCT.

LASERSTRAHLUNG: NICHT IN DEN

STRAHL BLICKEN. LASER KLASSE 2.

LUMIERE LASER: NE PAS REGARDER

DANS LE FAISCEAU. APPAREIL A LASER.

DE CLASSE 2 630-650nm, 1mW.

MADE IN CHINA

Honeywell International Inc.

www.honeywellaidc.com

Model:Voyager 1200g

Manufactured: December 2010

Rev. A

S/N: 00XXXXXXXXX

P/N: 1200g-1

Chapter 1 - Getting Started

About This Manual ...................................................... 1-1

Unpacking Your Device............................................... 1-1

Connecting the Device ................................................ 1-1

Connecting with USB ............................................ 1-1

Connecting with Keyboard Wedge........................ 1-2

Connecting with RS232 Serial Port....................... 1-3

Connecting with RS485......................................... 1-4

Reading Techniques ................................................... 1-4

Menu Bar Code Security Settings ............................... 1-5

Setting Custom Defaults ............................................. 1-5

Resetting the Custom Defaults ................................... 1-6

Resetting the Factory Defaults.................................... 1-6

Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1

Programming the Interface - Plug and Play ................ 2-1

Keyboard Wedge................................................... 2-1

IBM PS2 Keyboard................................................ 2-1

RS232 Serial Port.................................................. 2-1

RS485 ................................................................... 2-2

OPOS Mode.......................................................... 2-3

USB IBM SurePos................................................. 2-4

IBM Secondary Interface....................................... 2-4

USB PC or Macintosh Keyboard........................... 2-5

USB HID................................................................ 2-5

HID Fallback Mode................................................ 2-5

USB Serial Commands ............................................... 2-6

USB Serial Emulation............................................ 2-6

CTS/RTS Emulation.............................................. 2-6

ACK/NAK Mode..................................................... 2-7

Communication Timeout ....................................... 2-7

NAK Retries........................................................... 2-8

Support BEL/CAN in ACK/NAK............................. 2-8

Table of Contents

Verifone®Ruby Terminal Default Settings ..................2-9

Gilbarco®Terminal Default Settings............................2-9

Honeywell Bioptic Aux Port Configuration .................2-10

Datalogic™ Magellan©Bioptic

Aux Port Configuration ............................................2-10

NCR Bioptic Aux Port Configuration..........................2-10

Wincor Nixdorf Terminal Default Settings..................2-11

Wincor Nixdorf Beetle™ Terminal Default Settings...2-11

Keyboard Country Layout..........................................2-12

Keyboard Wedge Modifiers .......................................2-14

ALT Mode ............................................................2-14

Keyboard Style ....................................................2-14

Keyboard Conversion ..........................................2-15

Keyboard Modifiers..............................................2-16

Inter-Scan Code Delay ........................................2-17

<F0> Break Character .........................................2-18

Keyboard Wedge Defaults...................................2-18

RS232 Modifiers ........................................................2-19

RS232 Baud Rate................................................2-19

RS232 Word Length: Data Bits, Stop Bits,

and Parity .......................................................2-20

RS232 Handshaking............................................2-21

RS232 Timeout....................................................2-22

XON/XOFF ..........................................................2-22

ACK/NAK .............................................................2-23

Communication Timeout......................................2-23

NAK Retries .........................................................2-24

Support BEL/CAN in ACK/NAK ...........................2-25

RS232 Defaults....................................................2-25

NCR Modifiers ...........................................................2-25

NCR ACK/NAK ....................................................2-25

Block Check Character ........................................2-26

NCR Prefix...........................................................2-26

NCR Suffix ...........................................................2-26

NCR Prefix/Suffix.................................................2-27

NCR NOF (Not-on-File) Error ..............................2-27

Scanner to Bioptic Communication............................2-27

Andere Handbücher für VOYAGER 1200G

Inhaltsverzeichnis

Andere Honeywell Barcode-Lesegerät Handbücher

Honeywell

Honeywell MK7580-30A38-00-A - MS7580 Genesis - Wired Barcode... Bedienungsanleitung

Honeywell

Honeywell ms2420 Bedienungsanleitung

Honeywell

Honeywell 4800i Bedienungsanleitung

Honeywell

Honeywell Virtuos 1D Bedienungsanleitung

Honeywell

Honeywell VOYAGER 1250G Bedienungsanleitung

Honeywell

Honeywell MX7 Tecton Bedienungsanleitung

Honeywell

Honeywell 3800 Linear Series Bedienungsanleitung

Honeywell

Honeywell Eclipse MS5100 Series Bedienungsanleitung

Honeywell

Honeywell Hyperion 1300G Bedienungsanleitung

Honeywell

Honeywell 1900GHD-2 Bedienungsanleitung

Honeywell

Honeywell Solaris MS7820 Bedienungsanleitung

Honeywell

Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Bedienungsanleitung

Honeywell

Honeywell XL 800 Series Bedienungsanleitung

Honeywell

Honeywell PX4-6IE-CUTR-IG-1 Bedienungsanleitung

Honeywell

Honeywell Genesis 7580G Bedienungsanleitung

Honeywell

Honeywell YJ-HF5000 Bedienungsanleitung

Honeywell

Honeywell MS2422 Bedienungsanleitung

Honeywell

Honeywell XENON 1902 Bedienungsanleitung

Honeywell

Honeywell Fusion MS3780 Bedienungsanleitung

Honeywell

Honeywell MS9500 Voyager Series Bedienungsanleitung

Honeywell

Honeywell Xenon XP 1950h Bedienungsanleitung

Honeywell

Honeywell VOYAGER 1200G Bedienungsanleitung

Honeywell

Honeywell Dolphin 7600 Bedienungsanleitung

Honeywell

Honeywell Captuvo SL22 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung