Honeywell 8670 Bedienungsanleitung

8670-8BBC-EN-QS Rev A

12/18

8670 8-Bay Battery Charger

Quick Start Guide

Unpack your Battery Charger

After you open the shipping carton containing the product, take

the following steps:

• Check for damage during shipment. Report damage

immediately to the carrier who delivered the carton.

• Make sure the items in the carton match your order.

• Save the shipping container for later storage or shipping.

Introduction

The 8670 8-Bay Battery Charger simultaneously charges eight

rechargeable lithium ion batteries. The time required for

charging is dependent upon the battery internal temperature

and condition. The battery charger should be located in an area

that is well ventilated and not in high traffic areas. It should

have enough clearance to allow easy access to the power port

on the back of the device, and be protected from rain, dust,

direct sunlight or inclement weather. The charger is not

approved for use in hazardous locations.

This device is intended for indoor use only and requires an

indoor AC power source. The AC cord should not be stepped on,

tripped over or subjected to damage or stress.

Mount the 8670 8-Bay Battery Charger

Place the charger on a horizontal, hard surface or fasten

securely to a wall using the mounting holes. Mounting hardware

is not supplied by Honeywell.

Assemble the Power Supply

The AC power supply for the battery charger is shipped with the

battery charger. For non-US models a power cord is required.

1. Plug the A/C power cord into the power adapter.

2. Plug the power cable into the power connector on the back

of the 8670 8-Bay Battery Charger.

3. Plug the A/C power cord into a grounded power source. The

charger is now powered.

The charge pocket LEDs flash while the battery charger enters

and exits the startup check. The battery charger is ready for use

once the charge pocket LEDs are no longer illuminated.

Charge the Batteries

Hold the battery with its three charging contacts in line with the

three charging contacts in the charging pocket. Use the direc-

tion of the arrow on the battery label as a guide and align the

yellow dot on the battery with the yellow dot on the charger.

Firmly press the battery straight down into the battery charging

pocket.

It is important that batteries are inserted into the charging

pocket correctly. Inserting the battery incorrectly could result in

damage to the battery or the charger. Do not “slam” or slide the

battery into the pocket. This could damage the charger.

When a battery is placed in a charging pocket, the battery char-

ger begins charging the battery. There is a slight delay while the

charger evaluates the condition of the battery before charging

begins. While charging, the charger and battery will generate

enough heat to feel warm. This is normal and does not indicate a

problem. The red LED on the 8-Bay Charger indicates the bat-

tery is charging. A green LED indicates the battery has been

fully charged and can be removed.

Interpret the Charge Pocket LEDs

The battery pocket timers are dynamic and based upon the

capacity of the battery. There is a timeout period for the soft

start and another timeout period for the overall time required to

charge the battery to full capacity.

LED Indication

Red continuous Battery is charging.

Red flashing Battery charger fault or

failure.

Charging pocket timeout

period has expired.

Green continuous Battery charge is complete.

Yellow/Amber continuous Battery pocket is in standby

mode while warming up or

cooling down.

Battery is inserted incorrectly.

Make sure charging

terminals on battery and

charger are aligned.

No light on a charge pocket No battery in pocket.

Battery is not fully inserted.

Battery or charger is defective

or damaged.

No light on all charge pockets No power to charger.

No batteries in any pocket.

LED Indication

Battery Charger Help

Issue Cause Solution

Battery does

not fit in

charging

pocket

Different

manufacturer's

battery.

Use only Honeywell

lithium ion batteries,

model number HNP-40,

in this charger.

There is an

object in the

charging

pocket.

Unplug charger from AC

supply. Remove any dirt

or foreign objects from

the charging pocket.

No battery in

charger, but an

LED is on

Dirt or foreign

objects are in

the charging

pocket.

Unplug charger from AC

supply. Remove any dirt

or foreign objects from

the charging pocket. If

the LEDs continue to

remain ON, the charger

may be defective.

Contact Support at

www.honeywellaidc.com.

Charger is

plugged into a

live outlet,

battery is

inserted, but all

LEDs are off

Battery is not

makingcontact

with terminals

in the pocket.

Push battery in firmly.

Do not “slam” the battery

into the charging

pocket.

Faulty battery. Replace battery. If this

does not correct the

situation, contact

Support at

www.honeywellaidc.com.

Red LED comes

on when a fully

charged battery

is inserted

During the first

few minutes,

the battery

charger checks

the battery for

correct voltage

and charge

state. During

this time the

LED is red.

There is nothing wrong

with the battery or

charger. Do not “top off”

a fully charged battery

by repeatedly placing it

in the charging pocket.

The battery may

overheat and become

damaged.

Issue Cause Solution

Red LED is

flashing on any

pocket

Current could

not be sourced

through the

battery due to

age,

exhaustion, or

damage to the

cell(s).

Contact Support at

www.honeywellaidc.com

for battery replacement

options.

The charger’s

timeout period

has expired.

Make sure that the

battery temperature is

within specification and

try charging again. If this

does not correct the

situation, contact

Support at

www.honeywellaidc.com

for battery replacement

options.

Issue Cause Solution

Andere Handbücher für 8670

Inhaltsverzeichnis

Andere Honeywell Akkuladegerät Handbücher

Honeywell

Honeywell CT50-HB Bedienungsanleitung

Honeywell

Honeywell NSEK Bedienungsanleitung

Honeywell

Honeywell COB01 Bedienungsanleitung

Honeywell

Honeywell Dolphin 9500 Bedienungsanleitung

Honeywell

Honeywell MB4-BAT-SCN02 Bedienungsanleitung

Honeywell

Honeywell 057530.10 Gebrauchsanweisung

Honeywell

Honeywell HomeBase CX80 Bedienungsanleitung

Honeywell

Honeywell ChargeBase CT40-CB Bedienungsanleitung

Honeywell

Honeywell Xenon Ultra 196 Series Bedienungsanleitung

Honeywell

Honeywell CT50-QBC Bedienungsanleitung

Honeywell

Honeywell Captuvo SL22 Bedienungsanleitung

Honeywell

Honeywell MX9 Bedienungsanleitung

Honeywell

Honeywell PEHA 1602/2 Handbuch

Honeywell

Honeywell QuadCharger Bedienungsanleitung

Honeywell

Honeywell CX80-NB Bedienungsanleitung

Honeywell

Honeywell 70e-BTSC Bedienungsanleitung

Honeywell

Honeywell Dolphin CT40 Bedienungsanleitung

Honeywell

Honeywell Dolphin 7900 Bedienungsanleitung

Honeywell

Honeywell CX80 Quad Battery Charger Bedienungsanleitung

Honeywell

Honeywell 012168 Gebrauchsanweisung

Honeywell

Honeywell 010690.01 Gebrauchsanweisung

Honeywell

Honeywell Impact Series Gebrauchsanweisung

Honeywell

Honeywell Marathon Bedienungsanleitung

Honeywell

Honeywell RP2B Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung