Honeywell Gamewell GFANN-80 Technisches Handbuch
Document 53386:B3 4/25/2022 ECN 00016385
GFANN-80 & GFANN-80-W
Remote Fire Annunciator
Product Installation Document
General
The GFANN-80 Series Remote Fire Annunciators (GFANN-80,
GFANN-80-W) are compact, backlit LCD displays designed for use
with compatible FACPs (Fire Alarm Control Panels). The displays
mimic the FACP display and are capable of displaying English-language
text of system point status including device type, independent point
alarm, trouble or supervisory zone and custom labels programmed into
the FACP. Refer to the FACP manual installation section for detailed
system information and wiring.
Specifications
TB1 Terminals 1 & 2
Operating Voltage Range: 18.8VDC to 38.2VDC
Maximum Current Consumption:
• Normal/Standby (no activity): 39 mA
• Trouble Condition: 46 mA
• Alarm: 48 mA
• AC Fail (not backlit): 15 mA
TB1 Terminals 3 & 4
ANN-BUS rated at 5.5 VDC and 60 mA max.
Dimensions
6-7/8”W x 5-3/8”H x 1-3/8”D
Mounting
The GFANN-80 Series plastic enclosures can be surface or semi-flush
mounted in a single, double or 4” square electrical box.
To mount the GFANN-80 Series enclosure:
1. Open the GFANN-80 Series cover by turning the key switch
counterclockwise to the ON (Unlocked) position.
2. Push in the snap latch tab located on the right side while pulling the
cover open.
3. Pull wire through 7/8” hole in backplate and feed through wire
channel to lower left corner of backplate before routing to terminal
block (refer to appropriate FACP manual).
4. The cover must remain attached to the backplate while mounting
the annunciator to the electrical box/wall. The cover cannot be
reattached or removed after the annunciator has been mounted.
5. If the cover should become detached from the backplate, reattach as
shown below.
6. Surface or Semi-flush mount the GFANN-80 to a single, double or
4” square electrical box. The ANN-SB80KIT(-R/-B/-W) is an
available kit that contains two plastic backboxes that can be used to
surface mount the GFANN-80 Series.
NOTE: Installation and wiring must be done in accordance with
NFPA 72 and local wiring codes.
Backplate
Press in latch
and then
Pull open cover
Key switch shown
in OFF position
Cover with
LCD Display
Figure 1 Opening the GFANN-80 Series
GFANN-80
Series
Cover
GFANN-80
Series
Cover
GFANN-80
Series
Backplate
GFANN-80
Series
Backplate
• Position cover behind
backplate.
• Align hinge posts and
holes
•Slide holes down
onto posts.
• Close cover to lock
hinges into place.
Figure 2 Cover Reattachment
2GFANN-80 Series Installation Document — P/N 53386:B3 4/25/2022
Wiring the GFANN-80 Series to the FACP
Refer to Table 1 and Figure 3 for wiring connections.
Notes:
1. All connections/sources must be power-limited and supervised.
2. 12 - 22 AWG (0.33 - 3.31 mm2) wire for 24 VDC circuit is
acceptable.
3. Power wire distance limitation is set by 1.2 volt maximum line drop
from source to end of circuit.
4. Maximum distance from FACP to last ANN-BUS device must not
exceed 6,000 feet (1,800 m). Refer to the Wiring Distance Table in
the appropriate FACP manual for wire gauge and distance
limitations.
Setting the DIP Switches
Address Setting
Each ANN-BUS device requires a unique address. DIP switches 1-4 on
S1 are used to set the address. This address will be displayed on the
LCD display as the Station ID number.
Amaximum of 8 devices can be connected to the FACP ANN-BUS
communication circuit. ANN-BUS device addresses do not need to be
sequential and can be set to any number between 01 and 08. Note that 00
is not a valid address. The following illustrates the DIP switch settings
for each address (ID Number).
Communication Protocol
DIP switch 5 is used to determine the communication protocol of the
GFANN-80 Series. Set DIP switch 5 to ON for ANN-BUS protocol.
This switch must stay in the ON position for proper functionality.
End-of-Line Resistor
The end-of-line termination resistor must be enabled at S1 on the last
device on the communication circuit. All other annunciators should have
these switches set to disable.
DIP switches 7 and 8 are unused.
GFANN-80 Series
Terminals (TB1)
FACP ANN-BUS
Terminals
Terminal 1 (-) (-)
Terminal 2 (+) (+)
Terminal 3 (A) A (ANN-BUS)
Terminal 4 (B) B (ANN-BUS)
GFANN-80 Series
Terminals (TB2)
FACP ANN-BUS
Terminals
Terminal 1 Earth Ground
Table 1 GFANN-80 Series to FACP Connections
2
B (ANN-BUS)
A (ANN-BUS)
+ (24 VDC)
-(GND)
Connect to FACP ANN-BUS
and/or next device
Connect to FACP or UL Listed
Power Supply for Protective
Signaling and/or next device
GFANN-80 Series
Figure 3 Wiring the GFANN-80 Series to an FACP
}
}
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
ID Number
(Address)
(not valid) 00
01
02
03
04
05
06
07
08
DIP Switch S1
1 2 3 4 5 6 7 81 2 3 4 5 6 7 8
Ensure switch 5 is ON
1 2 3 4 5 6 7 81 2 3 4 5 6 7 8
termination enabled termination disabled
Dieses Handbuch passt für folgende Modelle
1
Andere Honeywell Bedienfeld Handbücher
Honeywell
Honeywell Galaxy 2 Series Bedienungsanleitung
Honeywell
Honeywell Notifier NFS2-640 Bedienungsanleitung
Honeywell
Honeywell GALAXY 16103 Bedienungsanleitung
Honeywell
Honeywell MiniZone EMM-3 Bedienungsanleitung
Honeywell
Honeywell HCM 200 Bedienungsanleitung
Honeywell
Honeywell Excel 5000 System Series Bedienungsanleitung
Honeywell
Honeywell NOTIFIER RP1r Bedienungsanleitung
Honeywell
Honeywell TrueZONE HZ432 Bedienungsanleitung
Honeywell
Honeywell Silent Knight IFP-2000 Module 3 Bedienungsanleitung
Honeywell
Honeywell TrueZONE HZ432 Bedienungsanleitung
Honeywell
Honeywell LYNX Touch 5100 Bedienungsanleitung
Honeywell
Honeywell THOR VM1 Bedienungsanleitung
Honeywell
Honeywell VARIODYN D1 Comprio Technisches Handbuch
Honeywell
Honeywell Notifier AFP-100 Bedienungsanleitung
Honeywell
Honeywell TrueZONE HZ221 Bedienungsanleitung
Honeywell
Honeywell Fire-Lite Alarms ACC-25/50 Bedienungsanleitung
Honeywell
Honeywell NOTIFIER INSPIRE E10 Bedienungsanleitung
Honeywell
Honeywell OMNI 408 Montageanleitung
Honeywell
Honeywell Fire-Lite Alarms ES-200X Bedienungsanleitung
Honeywell
Honeywell TotalZone TZ-4 Bedienungsanleitung
