Honeywell Silent Knight RA-2000 Bedienungsanleitung

RA-2000 Remote Annunciator

Installation

The optional Model RA-2000 Remote Annunciator, shown in

Figure 1, performs the same functions as the on-board

annunciator. Operation is identical. The RA-2000 can be surface

or flush monted.

Up to 8 RA-2000s can be added to the IFP-2000 system.

Figure 1: Model RA-2000 Remote Annunciator

RA-2000 installation involves the following steps:

1. Make sure power is off at the panel.

2. Mount the RA-2000 in the desired location (see Section

“Mounting the RA-2000” ).

3. Connect the RA-2000 to the panel (see Figure 2).

4. Use the dipswitches on the back of the RA-2000 to assign

an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N

151430).

5. The RA-2000 module must be added to the system through

programming. JumpStart AutoProgramming will add the

module automatically (refer to Manual P/N 151430).

Wiring Connections

Wire the RA-2000 to the FACP as Shown in Figure 2.

Figure 2: SBUS Connections

Specifications

Mounting the RA-2000

This section of the manual describes mounting the remote

annunciator. The annunciator can be flush- or surface-mounted.

Flush Mounting

This section of the manual describes flush mounting.

Follow these steps to flush mount the RA-2000

1. The back box dimensions are 9-3/8" w x 8-3/8" h. The

minimum depth 2". The back box can be mounted prior to

the complete installation of the RA-2000 using any of the

mounting holes shown in Figure 3.

Figure 3: Back Box Mounting Holes

2. Remove knockout holes as needed for wires. See Figure 4

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 25 mA

Alarm: 50 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

Dimensions:

Flush

Mount:

Overall: 12-1/4” W x 11.5” H x 7/8” D

31.1 cm W x 29.2 cm H x 2.2 cm D

See “Flush Mounting” for back box

dimensions.

Surface

Mount:

Including trim ring:

12-1/4” W x 11.5” H x 3” D

31.1 cm W x 29.2 cm H x 7.6 cm D

Mounting Holes

Model RA-2000 Installation Instructions

2P/N 151443 Rev A

7550 Meridian Circle, Suite 100

Maple Grove, MN 55369-4927

763-493-6455 or 800-328-0103

Fax: 763-493-6475

www.silentknight.com

for backbox knockout locations

Figure 4: Back Box Knockout Locations

3. Wire the Annunciator board to the main control panel. See

Figure 2.

4. Attach the annunciator and door assembly to back box as

shown in Figure 5 using the supplied screws.

Figure 5: Attaching Annunciator/Door Assembly to

Backbox

Surface Mounting

The Model RA-2000TG/TR trim ring kit is available for use

when surface mounting.

1. Remove the desired knock out. See Figure 4.

2. To properly mount the back box, insert a single screw into

the key shaped mounting hole. Do not tighten all the way.

See Figure 6.

Place a level on top of the back box, with the back

box level insert the rest of the mounting screws.

Figure 6: Back Box Surface Mount Holes

3. Run wires to the control panel.

4. Place the trim ring over the back box as shown in Figure 7.

Figure 7: Installing Trim Ring

5. Attach the Door assembly to the back box using screws

provided.

6. After the annunciator wiring to the panel has been

completed, replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws

on the bezel.

Wire Knockouts

Key Shaped

Mounting Hole

Back Box

Mounting Holes

Inhaltsverzeichnis

Andere Honeywell Bedienfeld Handbücher

Honeywell

Honeywell Fire-Lite Alarms MS-9050UD Bedienungsanleitung

Honeywell

Honeywell GX-Series Montageanleitung

Honeywell

Honeywell ENVIRAZONE PANEL W8835 Bedienungsanleitung

Honeywell

Honeywell GALAXY 16103 Bedienungsanleitung

Honeywell

Honeywell Galaxy 16 Bedienungsanleitung

Honeywell

Honeywell Gamewell GFANN-80 Technisches Handbuch

Honeywell

Honeywell Symphony Bedienungsanleitung

Honeywell

Honeywell VARIODYN D1 Comprio Technisches Handbuch

Honeywell

Honeywell AQ250 Series Bedienungsanleitung

Honeywell

Honeywell W834A Bedienungsanleitung

Honeywell

Honeywell Farenhyt Series Technisches Handbuch

Honeywell

Honeywell TrueZONE HZ311 Bedienungsanleitung

Honeywell

Honeywell LT-32 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER INSPIRE E10 Schulungshandbuch

Honeywell

Honeywell Domonial CMI 800++ Benutzerhandbuch

Honeywell

Honeywell Galaxy 18Galaxy Betriebsanleitung

Honeywell

Honeywell MS-9200UDLSE Bedienungsanleitung

Honeywell

Honeywell Tuxedo Touch Wi-Fi Montageanleitung

Honeywell

Honeywell NOTIFIER NFW-50X Bedienungsanleitung

Honeywell

Honeywell Domonial CMI Series Benutzerhandbuch

Honeywell

Honeywell NOTIFIER SFP-5UD Series Bedienungsanleitung

Honeywell

Honeywell IQ8Control C Bedienungsanleitung

Honeywell

Honeywell NOTIFIER INSPIRE E10 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER RP1r Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung