Honeywell EVOTOUCH CONTROLLER Bedienungsanleitung

Installation | Installation | Installatie | Installation | Installazione

evotouch

The Honeywell evotouch comfort control

system is a programmable zoning controller

with the following key features:

Features

• Largetouch-screendisplayforintuitive

operation by ﬁnger.

• Wallortable-topmounting.

Conguration

• Step-by-stepcongurationprocedure

bindsthecontrollertoeachofthe

devicesinthesystem.

• ChoiceofGuidedConguration,

forsimpleapplications,orExpert

Conguration,forcustomisingthe

conﬁguration.

 Note:evohomesystempacksarealready

precongured(seesystempackcontents

sheet).

Programmability

• Upto6periodsperdayineachofthe8

zones.

• Holidaymodereducesthetemperature

for1to99days.

• Economymodereducesthetemperature

settingsinallzones,toreducefuelbills.

Control

• Wirelesscontroltoboiler,radiator

controllers,roomsensors,andunder

ﬂoor heating controllers.

• Independentcontrolofupto8zones,to

optimisecomfortandminimiseenergy

usage.

• OptimumStartfeatureautomatically

calculates when to start heating to

achieve the correct temperature.

• AutomaticSummer/Wintertimechange.

Future expansion

• AUSBport,forfutureupdates.

Installation

Theproductisshippedwithpre-charged

batteries.However,formaximumtimeoffthe

dock,placetheproductoncharge.

Two mounting options are available:

• Awall-mounteddock.

• Atabletopstand.

Whenremovedfromthestand/dockthe

evotouchwillremainpoweredforabout

2hoursbeforeneedingtobereplacedfor

charging.

Productoverview

ENGLISH

Table-topstand

Theevotouchcanbepoweredfromthe

table-topstand.

• Attachtothestandasshown.

Removefrontcovertoexchangecoverplate

or access batteries.

Remove tab to activate batteries.

Batteriesandfrontcover

Rechargeable batteries. Replace with

AA1.2VNiMH2000-2400mAhbatteriesonly.

✓

✗✗

Installation instructions for wall mounting

StandardEU

SchukoWallbox

Minimum

depth

40mm

Insertwiresintopowermodule,observing

correct polarity

Pushpowermoduleintowallboxwithmains

wiring to the rear

Thepowermodulecanbeinstalledina

differentlocationfromtheevotouchunit.

Disconnect low voltage cable from wallplate

terminalblockandextendtheconnectionby

up to 10m max. using 1.0mm² cable. If smaller

sizecableisusedthemaximumdistancewill

reduce(e.g.5m max with 0.5mm² cable).

Observecorrectpolaritywhenconnectingthe

extensioncable.PowerSupplyCablewiresare

Red(+),Black(-).

Attention:Exceedingthemaximumcable

lengthcouldcausesystemmalfunction!

Attachwallplatetowallboxorsurface

(Powermoduleremote).

Optionalspacerforsurface

mounting.

1.2–1.5m

Positionwallboxataheightof1.2m-1.5m.

Caution:Isolatepowersupplyandmakesafebeforewiring

theunittopreventelectricshockandequipmentdamage.

Installationshouldbecarriedoutbyacompetentperson.

Wiresshould

protrude55mm

230V~mains.

230V~

mains.

Usescrewdriver

with 2.5mm

head

Remove

protective ﬁlm

Knock out

requiredholes

Attachevotouchto

wallplate

Notused

+ – X Y

Setting the language, date, and time

The ﬁrst time you apply power to the

evotouchyouwillbepromptedtoselecta

language for the user interface:

• Presstheappropriatelanguage.

Youwillthenbepromptedtosetthedate:

• Press or tosettheday,month,and

year respectively.

• PressDONEtoproceedtosettingthe

time.

• Press or tosetthehourand

minutes respectively.

You can optionally press CLOCK SETTINGS

tochangethetimeformatbetween24HR

and12HR,andchooseautomaticDaylight

Savingtime:

• PressDONEtoproceedwith

conﬁguration.

System conguration

Asequenceofscreensthenguides

you through an automatic conﬁguration

procedure:

• PressYEStoproceed.

YoucanalsoenterGuidedConguration

at any time by pressing the MENU button

for10seconds,andthenselecting

GUIDED CONFIG from the SYSTEM

CONFIGURATION menu.

Settingupevotouch

ENGLISH

Binding

GuidedCongurationbindseachofthe

controldevicesandsensorstoevotouch,to

ensure that the wireless communication is

working correctly.

Afterbindingeachdevice,aprompt

showswhetherbindingwassuccessful;for

example:

Bindingcanfailforthefollowingreasons:

- Thedeviceisnotswitchedon.

- Thedeviceistoofaraway.

- Therearetoomanysolidobjectsinthe

pathtothedevice.

Correcttheproblemandtryagain.

Editing names

During conﬁguration you are given the

optionofeditingthenamesusedtoidentify

the zones in the system. These are the

names seen by the user on the main Home

screen.

Toeditanamethefollowingscreenis

displayed:

• Presstodeletecharacters.

• PressABCtoenterupper-caseletters,

abctoenterlower-caseletters,or123 to

enterdigits.

• Presstheblankkeytoenteraspace.

• PressDONEwhennished.

Conguring mixed applications

TheGuidedCongurationdescribedonthe

following pages assumes all your zones use

thesametypeofcontrol.Ifyouhaveamixed

application,suchas5zoneswithradiator

controland3zoneswithunderoorheating

control,youcansetupthecongurationas

follows:

• UsetheGuidedCongurationto

congurethe5zonesforradiatorcontrol.

• UsetheADD ZONEoptiontoaddthe

3zonesforunderoorheatingcontrol;

see Adding a zone,page9.

• FinallyusetheSYSTEM

CONFIGURATION menu BINDING AND

RF TESToption,doingtheRFtestfor

eachzone.Formoreinformationseethe

Extended Installation Guide.

Conguration–GeneralFeatures

GuidedCongurationistherecommended

optionthersttimeyoucongureevotouch,

asitleadsyouthroughtheessentialstepsin

setting up a system.

• AtthepromptpressYEStoproceed.

Heat demand control

The ﬁrst step is to specify whether the

systemincludesaheatdemandboiler:

• PressNO or YES as appropriate.

IfyoupressedYESproceedasfollows.

IfyoupressedNO skip to the section

Applications below.

Ifthesystemincludesheatdemandcontrol,

thenextstepistocongurethewirelesslink

to the boiler controller:

• PressBIND.

ForinformationaboutbindingseeBinding

on the previous page.

• WhenbindingissuccessfulpressNEXT.

Thefollowingpromptisdisplayed:

• Installthedemanddeviceinitsproper

locationandputthedeviceintothetest

mode.

• PressNEXTwhenready.

Thefollowingpromptisdisplayed:

• PressNEXT.

Applications

The following menu allows you to specify

whichothercomponentsinthesystemneed

tobecongured:

• Selectthetypeofapplicationyouare

conﬁguring.

GuidedConguration

ENGLISH

Inasimplesystem,withevotouchacting

asthethermostattoaheatdemandboiler,

select Thermostat (1 zone),andasingle

zone will automatically be set up for you.

Inalargersystem,withradiatorcontrol

orunderoorheatingprovidingindividual

controlofseparateareas,youwillbe

promptedtosetupeachzone.

Thermostat (1 zone)

IfyouselectedTHERMOSTAT(1zone)the

zonenameisinitiallysettoLIVINGROOM:

• PressLIVING ROOMtoeditthename,

asdescribedinEditing namesearlier,or

NEXT to accept it.

NowproceedasdescribedinSpecifying the

sensors below.

Multizoning radiator heating or

Zone valves

IfyouselectedRADIATORHEATINGor

ZONEVALVESyouneedtospecifythe

number of zones in the system:

• Press or to specify the number of

zones,thenpressNEXT.

Thefollowingscreenletsyoueditthedefault

names chosen for the zones:

• Pressanyzonenametoeditit,as

describedinEditing namesearlier,or

press NEXT to continue.

Ifyouspeciedmorethan6zonespressMORE

toseeoredittheremainingzonenames.

Specifying the sensors

Foreachzonethedisplaypromptsyouto

specify the type of sensor:

• PressINTERNAL or EXTERNAL as

appropriate.

IfyouspeciedEXTERNAL you will then be

promptedtobindthesensor,asdescribed

in Binding earlier in this section.

• PressNEXT to repeat for the sensors in

each zone.

Whenallthezoneshavebeensuccessfully

conguredaconrmationisdisplayed.

•

Press DONE to return to the Home screen.

Note:Onlyonezonecanbecontrolledby

theinternalsensor.Selectingtheinternal

sensor automatically conﬁgures all other

zonestouseexternalsensors.

Addingazone

Thissectionexplainshowtoaddazone

toanexistingconguration,suchasafter

addinganHR80RadiatorControllerto

provideindependentcontrolofaroom.

• PressMENU from the home screen to

displaytheMainMenu.

• PressZONING MENUontheMainMenu

todisplaytheZoningMenu.

• PressZONING CONFIG on the Zoning

Menu.

Thefollowingwarningisdisplayed:

• Pressthebuttonfor5secondstodisplay

theZoningCongurationMenu.

• PressADD ZONE.

Youarerstpromptedtospecifythetypeof

application for the zone:

Formoreinformationaboutapplicationssee

the Extended Installation Guide.

Youarenextpromptedtonamethezone.

Thefollowingmenuthenallowsyoutobind

anactuatorandsensortothezone,andset

uptheschedule:

Forinformationaboutprogramminga

scheduleseetheQuick Start User Guide.

• PressBINDING MODEtobinddevicesto

the new zone.

Youarerstpromptedtobindtheactuatorin

the zone.

• PuttheactuatorinBINDmodeandpress

BIND.

Whenasuccessfulresponsehasbeen

received:

• PressDONE.

Thenextstepistobindasensorinthe

zone. You are given the option of using the

evotouchinternalsensor,oranexternal

room sensor.

Ifthezonecontainstheevotouchcontroller,

andyouwanttousetheinternalsensor,

press INTERNAL.

OtherwisepressEXTERNAL,andyouwill

bepromptedtobindaroomsensorinthe

zone.

• PresstheBIND button on the sensor.

Whenasuccessfulresponsehasbeen

received:

• PressDONE to return to the ADD ZONE

menu.

ENGLISH

Zoning boiler control with

BDR90 Relay module or RF

bridge

Initssimplestsingle-zone

congurationevotouchsensesand

controls the temperature in the main

room,usingitsinternalsensorand

calling for heat from the boiler via the

BoilerRelayorOpenthermBridge

accordingtothedesiredsetpoint.

HR80 radiator control with

central operation

Theevotouchcancontrolupto8zones

usingtheHR80radiatorcontroller.The

evotouch uses the valve position of the

HR80todeterminewhetherornotheat

isrequired.Itwillcontroltheboilervia

theboilerrelayorOpenthermBridge.

In this conﬁguration only the set point

issenttotheHR80s.TheHR80swill

comparethereceivedsetpointto

themeasuredzonetemperatureand

adjustthevalvepositionaccordingly.

Under oor heating control

with central operation and

room units DT92/HCW82

The evotouch can also integrate with

anunderoorheatingcontroller,and

roomunitsDT92/HCW82,toprovide

individualcontrolofupto8rooms.

TheDT92/HCW82roomsensorsand

setpointadjusterscommunicate

directlywithevotouch.

Three simple system applications

Relay module

Boiler Relay or Opentherm Bridge

Boiler

0 .. 100%

ON/OFF

19.

HR80

Relay module

Boiler Relay or Opentherm Bridge

Up to 8 zones

Boiler

0 .. 100%

ON/OFF

19.

Relay module

Boiler Relay or Opentherm Bridge

Antenna

HRA80

Up to 8 zones

Boiler

HCW82

DT92

0 .. 100%

ON/OFF

Underfloor heating

controller

HCE80(R)/HCC80(R)

19.5

Andere Handbücher für EVOTOUCH CONTROLLER

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Steuerungssystem Handbücher

Honeywell

Honeywell SILENT KNIGHT SK-Zone-6 Bedienungsanleitung

Honeywell

Honeywell touchpoint Pro Bedienungsanleitung

Honeywell

Honeywell Excel 800 Installations- und Betriebshandbuch

Honeywell

Honeywell W7080A Bedienungsanleitung

Honeywell

Honeywell C7400 Bedienungsanleitung

Honeywell

Honeywell ACC 50 Bedienungsanleitung

Honeywell

Honeywell SPZ-8000 Handbuch

Honeywell

Honeywell ComfortPoint Open Installations- und Betriebshandbuch

Honeywell

Honeywell R4184D Bedienungsanleitung

Honeywell

Honeywell 5704 Bedienungsanleitung

Honeywell

Honeywell RP-2002 Bedienungsanleitung

Honeywell

Honeywell Experion LX Bedienungsanleitung

Honeywell

Honeywell VR8404 Bedienungsanleitung

Honeywell

Honeywell BCS 3600 Bedienungsanleitung

Honeywell

Honeywell touchpoint Pro Versionshinweis

Honeywell

Honeywell AUTOMATIC CONTROL SI Edition Installations- und Betriebshandbuch

Honeywell

Honeywell NOTIFIER ACS Series Bedienungsanleitung

Honeywell

Honeywell W180 Bedienungsanleitung

Honeywell

Honeywell Experion LX Handbuch

Honeywell

Honeywell LYNX Touch Security System Bedienungsanleitung

Honeywell

Honeywell Excel 800 LION Installations- und Betriebshandbuch

Honeywell

Honeywell SmartValve SV9540 Bedienungsanleitung

Honeywell

Honeywell VR8205 Bedienungsanleitung

Honeywell

Honeywell UMC800 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung

EMKO

EMKO TRANS-SYNCRO Bedienungsanleitung

Dover

Dover TWG GC ELEMENT II Programmierhandbuch