Honeywell T7560B Bedienungsanleitung

® U.S. Registered Trademark

T7560A,B,C Digital Wall Module

HONEYWELL EXCEL 5000 OPEN SYSTEM

SPECIFICATION DATA

GENERAL

The T7560A,B Digital Wall Modules (DWM) display and

provide space temperature, setpoint, Occupied/Unoccupied

override, and fan mode/speed selection for the Honeywell

Excel 10 W7750, W7751, W7752, W7753, W7761, W7762,

W7763, and Excel 600, 500, 100, 50, 20 Controllers, as

applicable (a software module ModAL is available to adapt

the wall module to the respective Excel 20, 50, 100, 500, 600

controller. See T7560A,B,C Installation Instructions (product

literature no.: EN1B-0146GE51) for details.

Using the three buttons, the user can change room

temperature setpoint, fan mode/speed, initiate/cancel bypass,

and change configuration information such as the DWM’s

engineering units.

The T7560C Digital Wall Module (see inset above) has no

user interface (e.g. LCD, buttons, or setpoint dial) and issues

only temperature and humidity values.

These wall modules are not compatible with Honeywell

W7751A,C,E,G (VAV1) and W7752D1 (FCU1) Controllers.

FEATURES

•Fully compatible with all current Excel 10 and Excel

20 to 600 controllers.

•Low power consumption.

•Integral 20kΩNTC sensor.

•Separate mounting base for easy installation.

•Tamper-resistant locking cover.

•IP30 housing.

•T7560A and B, only:

- LCD display continuously shows current space

temperature, occupied/unoccupied/standby mode,

fan status/mode, humidity, as configured.

- Push-button interface for full navigation and

change control of wall module functions.

- Single-touch occupied/unoccupied override.

- Setpoint dial for setpoint adjustment.

- Fan Speed/Mode commandable from buttons.

- Selectable °F/°C temperature display.

- Selectable setpoint type, absolute or relative.

T7560A,B,C DIGITAL WALL MODULES

EN0B-0237GE51 R0208 2

SPECIFICATIONS

Models

Table 1. Types of DWM

sensor

colors

(dial / housing)

pre-conf.

units

T7560A1000 Tmp blue/white °C

T7560A1026 Tmp white/white °C

T7560A1018 Tmp white/white °F

T7560B1008 Tmp/Hum blue/white °C

T7560B1024 Tmp/Hum white/white °C

T7560B1016 Tmp/Hum white/white °F

T7560C1006 Tmp/Hum blue/white n.a.

Tmp = Temperature sensor; Hum = Humidity sensor

Temperature Sensor Accuracy

The DWM is furnished with a 20kΩNTC temperature

sensor that follows a specific temperature-resistance curve.

See Fig. 1. Honeywell controllers used with the DWM

employ an algorithm that provides readings close to the

actual temperature. Table 2 summarizes the DWMsensor

accuracy for normal operating temperatures. Across the

range of 43 to 104°F (6 to 40°C), the accuracy is better

than ±0.75°F (±0.42°C).

80 K

70 K

60 K

50 K

40 K

30 K

20 K

10 K

010 20 30 40

40 50 60 70 80 90 100 110 °

°C

temperature (degrees)

elec

ical

ance (

)

Fig. 1. Temperature vs. resistance for 20kΩsensor

Table 2. Temperature sensor accuracy

ambient tem. (°C) max. error (°C) nominal re-

sistance (Ω)

15.5 ±0.29 31543

18.3 ±0.27 27511

21.1 ±0.27 24047

26.7 ±0.27 18490

29.5 ±0.29 16264

Humidity Sensor

Table 3. Humidity sensor specifications

parameter value

humidity sensing range 5 … 95% r.h.

output signal 0.5 … 10 Vdc (5…100% r.h.)

accuracy ±5% (full-scale)

Fan Speed Button (T7560A,B, only)

Table 4. Fan speed resistances

switch position resistance (Ω) fan behavior

auto 1681.4 ±100 runs as scheduled

0 2686.4 ±100 OFF

1 3866.4 ±100 runs at speed 1

2 3041.4 ±100 runs at speed 2

3 4601.4 ±100 runs at speed 3

bypass activated 0 ... 100 unchanged

NOTE:

If connected to Excel 10 UV Controller W7753, fan

output will not be shorted to ground on pressing

the BYPASS button; with every other Excel 10

Controller, it will be shorted.

See T7560A,B,C Installation Instructions (product

literature no.: EN1B-0146GE51) for configuration.

Power Supply

24 Vac/dc with a valid range of 18 ... 30 V

5 Vdc via LED input with a valid range of 5 ... 12 V

See T7560A,B,C Installation Instructions (product literature

no.: EN1B-0146GE51) for details.

Power Consumption

2 VA at 24 Vac, 50/60 Hz

DWM Setpoint Adjustment

The relation between setpoint and resistance is given in

Table 5 and Table 6. Accuracy of resistance is:

•

5% in middle position, e.g. 5225 Ωto 5775 Ω

•

10% in end position, e.g. 9450 Ωto 11550 Ω.

Setpoint accuracy: ± 0.2 K

T7560A,B,C DIGITAL WALL MODULES

3 EN0B-0237GE51 R0208

Table 5. Setpoint values vs. resistances (Celsius)

setpoint

rel./K

nom. res.

(Ω) setpoint

abs./°C

nom. res.

(Ω)

-5 9574.0 12 9958.0

-4 8759.2 13 9468.7

-3 7944.4 14 8979.3

-2 7129.6 15 8490.0

-1 6314.8 16 8000.7

0 5500.0 17 7511.3

1 4685.2 18 7022.0

2 3870.4 19 6532.7

3 3055.6 20 6043.3

4 2240.8 21 5554.0

5 1426.0 22 5064.7

23 4575.3

24 4086.0

25 3596.7

26 3107.3

27 2618.0

28 2128.7

29 1639.3

30 1150.0

Table 6. Setpoint values vs. resistances (Fahrenheit)

setpoint

rel./K

nom. res.

(Ω) setpoint

abs./°C

nom. res.

(Ω)

-10 10026.7 55 9577.4

-9 9574.0 57 9033.7

-8 9121.3 59 8490.0

-7 8668.7 61 7946.3

-6 8263.7 63 7402.6

-5 7763.3 65 6858.9

-4 7310.7 67 6315.2

-3 6858.0 69 5771.5

-2 6405.3 70 5499.6

-1 5952.7 71 5227.8

0 5500.0 73 4684.1

1 5047.3 75 4140.4

2 4594.7 77 3596.7

3 4142.0 79 3053.0

4 3689.3 81 2509.3

5 3236.7 83 1965.6

6 2784.0 85 1421.9

7 2331.3

8 1878.7

9 1426.0

10 973.3

Field Wiring

•

16 to 22 AWG (1.5 to 0.34 mm

) depending on

application.

•

18 AWG (1.0 mm

) min. for 24 Vac power wiring.

•

Max. length of wire from a device to a wall module is

164 ft (50 m).

•

Twisted pair wire recommended for wire runs longer

than 100 ft (30.5 m).

Setpoint Adjustment Range (A and B)

Setpoint can be configured for

•

Fahrenheit absolute (55 ... 85 °F)

•

Fahrenheit relative (

10)

•

Celsius absolute (12 ... 30 °C)

•

Celsius relative (

Temperature Value Display Resolution (A and B)

Degree Celsius

⇒

0.1 °C

Degree Fahrenheit

⇒

0.1 °F

Setpoint Value Display Resolution (A and B)

Degree Celsius

⇒

0.5 °C

Degree Fahrenheit

⇒

1.0 °F

Mounting Options

Wall mounting

Dimensions(H/W/D)

4-1/8 x 3-15/16 x 1-3/16 in. (104 x 99 x 30 mm)

Environmental Ratings

Shipping temperature: -22 ... +140 °F (-30 ... 60 °C)

Operating temperature: 32 ... 104 °F (0 ... +40 °C)

Relative humidity: 5% to 95% non-condensing

Measurement range: +6 … +40 °C

Approval Bodies

UL 916, NEC Class 2

T7560A,B,C DIGITAL WALL MODULES

EN0B-0237GE51 R0208 4

OPERATION OF THE DWM

Table 7. Supported DWM functions with Excel 10 Controllers

bypass unit enable fan override setpoint humidity room temp.

W7750 CVAHU 3

N/A N/A

W7751 VAV 3

N/A N/A

N/A

W7752 FCU 3

N/A

W7753 UV 3

W7761 RIO

N/A N/A N/A N/A

W7762 HYD 3

N/A N/A

N/A

W7763 CHC 3

N/A N/A

General

The T7560A and T7560B feature three buttons, a setpoint

dial, and the LCD display (see Fig. 2). This section describes

the functions of these elements. Table 7 shows the functions

available with the different Excel 10 Controllers.

Fig. 2. Control elements of DWM.

NOTE:

If not specified differently, the graphics given below

show example display settings; depending on

configuration, the actual indications may vary from

those shown hereinafter.

Set Temperature

Depending on the configuration, you can adjust the

temperature within the limits given below:

°C absolute

⇒

12 to 30°C (in 0.5 steps)

°C relative

⇒

-5 to +5 (in 0.5 steps)

°F absolute

⇒

55 to 85°F (in 1.0 steps)

°F relative

⇒

-10 to +10 (in 1.0 steps)

Turn the SETPOINT DIAL

up/down to decrease/increase

the room temperature setpoint.

The display toggles the setpoint

value (either relative or absolute,

as configured).

After the new setpoint has been

set, the display returns to normal

mode after approx. 5 sec.

Set Fan Speed

The manually set fan speed is represented by a bargraph.

Depending on configuration, the fan speed can be set as

follows:

Three-speed fan override

⇒

AUTO, OFF, 1, 2, 3

Two-speed fan override

⇒

AUTO, OFF, 1, 2

Fan mode override

⇒

AUTO, OFF, ON

NOTE:

The default setting after power-up is AUTO. The

manually set fan speed overrides the controller’s

control algorithm.

Three-speed fan override

Press the FAN OVERRIDE button to toggle between:

AUTO

(fan speed from controller)

MANU OFF

(fan off)

With this setting, depending on

configuration, the display may

also read:

Humidity Display

If applicable, the humidity is indicated by the bargraph at the

top of the LCD. Each segment of the bargraph represents 4%

of relative humidity:

NOTE:

Humidity display is not available with fan control.

Humidity mode

(e.g. left 12 segments ON =

50% relative humidity)

Set Bypass/Occupancy Mode Display

The bypass function can be used to override the control

algorithm generated by the controller (e.g. for an event after

normal office hours, or for a room known to be unused).

The status of the occupancy mode can be seen from the sun,

moon, and snowflake symbols. The following LCD behaviors

are possible, depending on configuration. See T7560A,B,C

Installation Instructions (product literature no.: EN1B-

0146GE51) for configuration options:

Occupancy mode display for Excel 10 LCD signaling

(Excel 10 set to LCD_DISPLAY; with FCU, HYD, and

CHC, only.)

Effective Occupancy or Bypass mode

(SUN continuously ON)

Effective Standby mode; generated by

time program

(HALF-SUN continuously ON)

Effective Unoccupancy mode

(MOON continuously ON)

Unit Off, No Frost Protection

(OFF without snowflake)

Unit Off, With Frost Protection

(OFF WITH SNOWFLAKE)

Override Standby mode (from central)

(HALF-SUN FLASHING)

Wink mode (NEURON

ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Press the BYPASS button to set the desired mode:

•

To activate Override Occupancy or Bypass mode,

press and release the BYPASS button.

•

To activate Override Unoccupancy mode, press

and hold the BYPASS button for at least 5 sec.

•

To return to normal mode, press and release the

BYPASS button again.

NOTE:

Pressing the BYPASS button for more than 5

seconds sends the NEURON

ID of the connected

Excel 10 controller via the L

ORKS

network.

Override Occupancy or Bypass mode

(SUN FLASHING)

Override Unoccupancy mode

(MOON FLASHING)

Override mode display for Excel 10 LED signaling (Excel

10 set to LED_OVERRIDE)

Off Conditions, No Override, Overr.

Occupancy, Overr. Standby (NO

SYMBOLS)

Wink mode (NEURON

ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Press the BYPASS button to set the desired mode:

•

To activate Override Bypass mode, press and release

the BYPASS button.

•

To activate Override Unoccupancy mode, press and hold

BYPASS button for at least 5 sec.

•

To return to normal mode, press and release the

BYPASS button again.

NOTE:

Pressing the BYPASS button for more than 5

seconds sends the NEURON

ID of the connected

Excel 10 controller via the L

ORKS

network.

Override Bypass mode

(SUN FLASHING)

AUTO

MANU

T7560A,B,C DIGITAL WALL MODULES

Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37, Switzerland by its Authorized Representative:

Automation and Control Solutions

Honeywell GmbH

Böblinger Straße 17

D-71101 Schönaich

Phone: (49) 7031 63701

Fax: (49) 7031 637493

http://ecc.emea.honeywell.com

Subject to change without notice. Printed in Germany

EN0B-0237GE51 R0208

Override Unoccupancy mode

(MOON FLASHING)

Occupancy mode display for Excel 10 LED

signaling (Excel 10 set to LED_OCCUPANCY)

Effective Bypass mode

(SUN continuously ON)

Effective Standby mode; generated by

time program

(HALF-SUN continuously ON)

Off Conditions, Effective Unoccupancy

mode

(MOON continuously ON)

Wink mode (NEURON

ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Occupancy mode display for Excel 20 to 600

Display of the currently active Excel 20 to 600 mode; further

options depend on the configuration of the controller:

Occupancy mode

(SUN continuously ON)

Standby mode; generated by time

program

(HALF-SUN continuously ON)

Unoccupancy mode

(MOON continuously ON)

To adapt the T7560 to the CARE control strategies for Excel

20 to 600, a standard ModAL software module is available.

Contact your local Honeywell distributor, or refer to

T7560A,B,C Installation Instructions (product literature no.:

EN1B-0146GE51) for further details.

ACCESSORIES

For mounting the following accessories, please refer to the

T7560A,B,C Installation Instructions (product literature no.:

EN1B-0146GE51).

T7460-LONJACK

The T7460-LONJACK is a small board and allows easy

access to L

ORKS

via the wall module (the wall module

must be already connected, in compliance with the max.

cable lengths set forth by the L

ORKS

Guidelines, to the

ORKS

network via a L

ORKS

bus cable). Via an

additional 3.5 mm jack plug on the board, a PC connection

can be established.

Order quantity: set of 5 pieces

T7560 Blinds

Same material and color as housing; for covering non-

operational buttons.

Order quantity: set of 50 pieces.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell Ultrakey Lite Bedienungsanleitung

Honeywell

Honeywell 190887-EET Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Betriebsanleitung

Honeywell

Honeywell Pressuretrol P7810C Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE EAGLEHAWK NX Installations- und Betriebshandbuch

Honeywell

Honeywell Aquastat L7224U Bedienungsanleitung

Honeywell

Honeywell AQ251 Installationsanleitung

Honeywell

Honeywell Design and Application Produkthandbuch

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell Aquastat L8100C Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell WV8860C Bedienungsanleitung

Honeywell

Honeywell T6590A Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

Honeywell

Honeywell Spyder 7 Bedienungsanleitung

Honeywell

Honeywell MS7503A2023 Bedienungsanleitung

Honeywell

Honeywell Excel 10 W7752D Bedienungsanleitung

Honeywell

Honeywell T775A Bedienungsanleitung

Honeywell

Honeywell WV8840A Bedienungsanleitung

Honeywell

Honeywell VU443A Bedienungsanleitung

Honeywell

Honeywell LYNX Touch L5200 Series Bedienungsanleitung

Honeywell

Honeywell Spyder PUB6438S Bedienungsanleitung

Honeywell

Honeywell MP953D Bedienungsanleitung

Honeywell

Honeywell UDC3500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch