Honeywell UDC 6300 Leitfaden

11/99 Kit Instruction 51-52-33-85C 1 of 5

UDC 6300 Process Controller

Upgrade PROM

Replacement Instruction

Document Number Form: 51-52-33-85C

Effective: 11/99

Supersedes: 3/99

Kit contents This kit contains one of the following Upgrade PROMs

Description Part Number

Adaptive Tune 51450900-501

Adaptive Tune + Math 51450900-502

Adaptive Tune + 2 Loops + Cascade 51450900-503

All Options 51450900-504

TPS Integration 51309350-501

Modbus RTU 51309350-502

Basic PROM 51309181-501

Equipment needed

• Phillips Head Screwdriver

• Flat Bladed Screwdriver

• Small Pliers

Continued on next page

2 of 5 Kit Instruction 51-52-33-85C 11/99

Replacement Instruction, Continued

How to remove the

chassis Refer to Figure 1 for reference and follow the procedure listed in Table 1.

Table 1 How to Remove the Chassis

Step Action

1 Pull down the flap covering the front screw and loosen the screw.

2 Grasp the bezel and pull the chassis out of the case.

Figure 1 Chassis Removal

Rear of case

23045

Front Screw

Bezel/Keyboard/Display Assembly

Continued on next page

11/99 Kit Instruction 51-52-33-85C 3 of 5

Replacement Instruction, Continued

How to install the

PROM

Table 1 How to Install the PROM

Step Action

1 The PROM is located on the MCU/Input printed wiring board at

location U109. See Figure 2 for location.

If a Communications Board is not present:

2 Lay the chassis on its left side on a non conductive surface

3 Insert a small screwdriver under the PROM and lift up to remove.

4 Orient the PROM to the socket and press into place.

5 Return the chassis to the case and configure the controller to include

the new features.

If a Communications Board is present:

6 Go to Table 2.

Figure 2 Parts Identification

23044

Rear of case

Front Screw

Communications

PWB

MCU/Input PWB

Option Input PWB

Power/ DIO PWB

Bezel/Keyboard/

Display Assembly

SpacerInterconnect

Interconnect

PWB Mounting Screws (4)

Cable Assembly

Power/DIO PWB

to Option Input Board

Mounting Screw

Chassis

EEPROM

at U106

PROM

(on MCU/Inputs

board at U109)

Continued on next page

4 of 5 Kit Instruction 51-52-33-85C 11/99

Replacement Instruction, Continued

How to remove the

Bezel/Keyboard/

Display assembly

In order to access the PROM if your controller has a Communications

Board, you must remove the Bezel/Keyboard/Display assembly from the

chassis and access the printed wiring boards.

The procedure in Table 2 lists the steps required to remove the

Bezel/Keyboard/Display assembly.

Table 2 How to Remove the Bezel/Keyboard/Display Assembly

Step Action

1 Remove the two screws on the bottom of the chassis frame that hold

the Bezel/Keyboard/Display assembly in place on the chassis frame.

Refer to Figure 2 for reference.

2 Lift the two retainers slightly away from the MCU/Input board notch

and the Power/DIO board on the opposite side as shown below.

The Bezel/Keyboard/Display board assembly will come away in one

piece.

Power/DIO

Board

MCU/Input

Board

Lift

retainers

here

Top of

rubber bezel

UDC6300

3 Install the PROM supplied in this kit.

See Table 3.

4 Reinstall the Bezel/Keyboard/Display assembly.

CAUTION Be careful to align the pins on the display board with

the mating connector P9 on the MCU/Input board.

5 Reattach the bezel assembly to the chassis with the screws

previously removed.

Continued on next page

11/99 Kit Instruction 51-52-33-85C 5 of 5

Replacement Instruction, Continued

How to install the

PROM Follow the procedure in Table 3 to access the PROM.

Table 3 Access the PROM

Step Action

1 Remove the four screws (two on each side) that hold the two main

printed wiring boards onto the chassis (See Figure 2 for location)

2 Use pliers to squeeze the ends of the spacer and push it through

the Power/ Digital I/O PWB. (See Figure 2 for location of spacer)

3 Gently pull the MCU/Inputs and the Power/DIO boards apart out of

the top and bottom interconnectors and lay the boards flat on a

non-conductive surface. (See figure 3).

4 Identify the Communications Option board (If present) and remove

the two screws that hold it onto the MCU/Inputs PWB.

5 Figure 3 identifies the location of the PROM.

6 Insert a small screwdriver under the PROM and lift up to remove.

7 Orient the PROM to the socket and press into place.

8 Reassemble the Communications Option PWB to the MCU/Inputs

PWB.

9 Reassemble the interconnects to the MCU/Inputs board and

reassemble the boards reversing the procedure above.

10 Reattach the Bezel/Keyboard/Display board assembly as listed in

Table 2 - steps 4 and 5.

11 Return the chassis to the case and configure the controller to

include the new features.

Figure 3 Printed Wiring Board Identification

Communications

Option Board

Option

Input Board

Power / DIO Board

MCU/Inputs

Board

J14

P14

U109

PROM Location

Pin 1

23046

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell HVC0002 Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE MERLIN NX Series Bedienungsanleitung

Honeywell

Honeywell Spyder 5 Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE LION CLLIONLC01 Installations- und Betriebshandbuch

Honeywell

Honeywell Experion PKS Gebrauchsanweisung

Honeywell

Honeywell ML7430E Bedienungsanleitung

Honeywell

Honeywell HR 80 Bedienungsanleitung

Honeywell

Honeywell MIWI350 Betriebsanleitung

Honeywell

Honeywell HCE 40 Programmierhandbuch

Honeywell

Honeywell BC7000L1000 Handbuch

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell ML6194 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

Honeywell

Honeywell Spyder BACnet PUB1012S Bedienungsanleitung

Honeywell

Honeywell WEB/CP-202-XPR Bedienungsanleitung

Honeywell

Honeywell WEB-300E Series Bedienungsanleitung

Honeywell

Honeywell UDC3500 Bedienungsanleitung

Honeywell

Honeywell UltraKey Touch HJC4000 Bedienungsanleitung

Honeywell

Honeywell S9361A207 Series Bedienungsanleitung

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Honeywell

Honeywell ComfortPoint Open CPO-VAV2A Bedienungsanleitung

Honeywell

Honeywell M896 Bedienungsanleitung

Honeywell

Honeywell ML4125 Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung