Honeywell BIRNHAM Bedienungsanleitung

BIRNHAM 52” CEILING FAN

MODEL #50191,50192

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,

8 am - 5 pm, EST.

Español p. 20

WELCOME

PREPARATION

Before beginning the assembly of this product, ensure

that all parts are present. Compare all parts with the

package contents list and hardware contents list. If

any part is missing or damaged, do not attempt to

assemble the product.

After opening the top of the carton, remove the

mounting hardware package from the foam inserts,

then remove the motor from the packaging and

place it on a soft surface, such as a carpet, to avoid

damage to the nish.

Estimated Assembly Time: Under 60 minutes

Tools Required for Assembly (not included): Electrical

Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Step Ladder, and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape

Measure, Wiring Handbook, and Wire Cutters

CARE AND MAINTENANCE

At least twice each year, lower the canopy to check

the downrod assembly, and then tighten all screws

on the fan. Clean the motor housing with only a soft

brush or lint-free cloth to avoid scratching the nish.

Clean the blades with a lint-free cloth. You may

occasionally apply a light coat of furniture polish to

wood blades for added protection.

Important: Shut off the main power supply before you

begin any maintenance tasks. Do not use water or a

damp cloth to clean the ceiling fan.

FAN WEIGHT

The net weight of this fan is: 18.7 lbs. (8,48 kg).

TABLE OF CONTENTS

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Care and Maintenance ........................2

Package Contents ...........................3

Safety Information ...........................4

Mounting Options ............................5

Mounting Bracket Installation ...................6

Standard or Angle Mounting Instructions . . . . . . . . . .7

Closemount Instructions......................10

Wiring ....................................11

Canopy Installation..........................12

Blade Installation ...........................13

Light Kit Installation .........................14

Operating Installation . . . . . . . . . . . . . . . . . . . . . . . .16

Replacement Parts List ......................17

Troubleshooting ............................18

Limited Lifetime Warranty.....................19

PACKAGE CONTENTS

Unpack your fan and check the contents. You should

have the following items:

1. Motor Housing

2. Light Kit Fitter

3. Blade Arm (5)

4. Canopy

5. Mounting Bracket

6. Canopy Cover

7. Optional Cap

8. Downrod Assembly

9. Blade (5)

10. Yoke Cover

11. Glass Shade (4)

12. Bulb (4)

13. Loose parts bags containing (not shown): Mounting

hardware, blade attachment hardware, electrical

hardware, pull chains, wire connectors, etc.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

• Before you begin installing the fan, disconnect the power by removing fuses or turning off the

circuit breakers.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code, and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring handbook if

you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. (2,14 m) from the

blades to the oor and at least 30 in. from the end of the blades to any obstruction.

DANGER

WARNING

When using an existing outlet box, make sure

the outlet box is securely attached to the building

structure and can support the full weight of

the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is

essential in minimizing wobble and noise in the

fan after installation is complete.

To reduce the risk of re or electric shock, do not

use the fan with any solid-state speed-control

device or control the fan speed with a full-range

dimmer switch.

To reduce the risk of re, electric shock, or personal

injury, mount the fan to an outlet box marked

“ACCEPTABLE FOR FAN SUPPORT” and use the

mounting screws provided with the outlet box. Most

outlet boxes commonly used for the support of

lighting xtures are not acceptable for fan support

and may need to be replaced. Consult a qualied

electrician if in doubt. Secure the outlet box directly

to the building structure. The outlet box and its

support must be able to support the moving weight

of the fan, at least 35 lbs. (15,88 kg).

WARNING

CAUTION

To reduce the risk of re, electric shock, or

personal injury, do not bend the blade arms

when installing them, balancing the blades, or

cleaning the fan. Do not insert objects between

the rotating fan blades.

Read all instructions and safety information

before installing your new fan. Review the

accompanying assembly diagrams.

Carefully check all screws, bolts, and nuts on

the fan motor housing to ensure that they are

secured.

MOUNTING OPTIONS

DANGER

Turn off the circuit breakers and the wall

switch to the fan supply line leads. Failure to

disconnect the power supply prior to installation

may result in serious injury or death.

Fig. 1

Fig. 2

Fig. 3

1. Your fan has 3 mounting options:

• Standard (Fig. 1)

• Angled (Fig. 2)

• Closemount (Fig. 3)

Note: The fans in gures 1 through 3 are not the actual

fan in your package, they are representation of the

3 different mounting options.

Important: If using the angle mount, check to ensure

the ceiling angle is not steeper than 16°.

Helpful Hint: Standard mounting is best suited for

ceilings 8 ft. or higher. For taller ceilings you may

want to use a longer downrod (sold separately).

Angled mounting is best suited for angled or vaulted

ceilings. A longer downrod is sometimes necessary

to ensure proper blade clearance. Closemount-style

mounting is more suitable for ceilings lower than 8

ft. (2,44 m) high.

2. Ensure that the blades of the fan are 30 in. (76 cm)

from any obstruction.

3. Check the downrod length to ensure the blades will

be at least 7 ft. (2,14 m) above your oor.

! !

Fig. 5

MOUNTING BRACKET INSTALLATION

Fig. 4

Mounting Bracket

Screws

Mounting

Bracket

Canopy

Washer

4. Loosen all four mounting bracket screws. Remove

the two canopy screws and washers from the round

holes of canopy. Set aside for later use. Detach

mounting bracket from canopy (Fig. 4).

5. Secure the mounting bracket to the outlet box using

screws and washers provided with the outlet box

(not included) (Fig. 5).

Note: It is very important that you use proper hardware

when installing the mounting bracket as it supports

the fan.

Important: If using the angle mount, ensure that the

open end of the mounting bracket is installed facing

the peak of the ceiling.

Mounting

Bracket Screw

Washer

Fig. 8

Downrod

Canopy

Yoke

Cover

Motor

Housing

STANDARD OR ANGLE MOUNTING INSTRUCTIONS

Downrod

Clip

Downrod

Fig. 6

Fig. 7

Set Screws

Downrod Pin

Downrod Clip

6. Partially loosen the two set screws in the yoke at

the top of the motor housing (Fig. 6).

7. Remove the downrod pin and downrod clip from

the downrod (Fig. 7).

8. Thread the wires from the motor housing through

the yoke cover, canopy and out through the top of

the downrod (Fig. 8).

STANDARD OR ANGLE MOUNTING INSTRUCTIONS

9. Slide the downrod into the yoke of the motor

housing, align the holes, and re-install the downrod

pin and downrod clip. Then re-tighten the two set

screws (Fig. 9).

10. Depending on the length of downrod you use, you

may need to cut the lead wires back to simplify the

wiring. If you decide to cut back the lead wires,

it is suggested that you do so in the following

manner: Take the lead wires and make sure that

you have pulled them all the way through the top

of the downrod and measure 8 in. of lead wire, and

then cut the excess wire off with wire cutters (not

included) (Fig. 10).

11. If you cut back the lead wire in Step 10, strip 1/2 in.

of insulation from the end of each wire. Twist the

stripped ends of each strand of wire clockwise with

pliers (not included) (Fig. 11).

Note: If you did not cut back the lead wires in Step 10,

Step 11 is not necessary and you may proceed to

Step 12 instead.

Downrod

Set Screw

Downrod

Clip

Fig. 9

Fig. 10

Fig. 11

Cut Wires

Stripped

Wires

Downrod Pin

Downrod Clip

Mounting

Bracket

Downrod

Ball

Tab

Slot

Fig. 12

STANDARD OR ANGLE MOUNTING INSTRUCTIONS

12. Install the downrod ball into the mounting bracket

opening. Rotate the fan and/or downrod until the

slot in the downrod ball engages the tab in the

mounting bracket. The rod should not rotate if

installed correctly (Fig. 12).

Closemount

Screws

Spring

Washer

Fig. 14

CLOSEMOUNT INSTRUCTIONS

13. Remove the canopy cover from the bottom of the

canopy (Fig. 13).

Helpful Hint: Closemount-style mounting is more

suitable for ceilings lower than 8 ft. (2,44 m) high.

The downrod and canopy cover are not used in this

type of installation.

15. Raise the fan and place the canopy on the hook

located on the mounting bracket for wiring (Fig. 15).

Canopy

Hook

Canopy

Cover

Fig. 13

Fig. 15

Closemount Screw Spring Washer

14. Align the canopy with the closemount screw holes

in the top of the motor housing. Secure the canopy

to the top of the motor housing by installing three

closemount screws and spring washers (Fig. 14).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Lüfter Handbücher

Honeywell

Honeywell HT-908 Series TECH FORCE Bedienungsanleitung

Honeywell

Honeywell ELSTON Bedienungsanleitung

Honeywell

Honeywell HSF600B Bedienungsanleitung

Honeywell

Honeywell HT-800E Bedienungsanleitung

Honeywell

Honeywell HFT-3108B Bedienungsanleitung

Honeywell

Honeywell HYF260E Bedienungsanleitung

Honeywell

Honeywell DreamWeaver HTF400 Series Bedienungsanleitung

Honeywell

Honeywell HYF260W Series Bedienungsanleitung

Honeywell

Honeywell RIO Bedienungsanleitung

Honeywell

Honeywell 50609 Bedienungsanleitung

Honeywell

Honeywell 50616 Bedienungsanleitung

Honeywell

Honeywell HT350 Series Bedienungsanleitung

Honeywell

Honeywell PERFECT WINDOW ER150 Bedienungsanleitung

Honeywell

Honeywell HFS-641PC Bedienungsanleitung

Honeywell

Honeywell 50206 Bedienungsanleitung

Honeywell

Honeywell HSF600BE Bedienungsanleitung

Honeywell

Honeywell TURBO FORCE HT-906 Series Bedienungsanleitung

Honeywell

Honeywell HW-500C Series Bedienungsanleitung

Honeywell

Honeywell SUPER TRADELINE L4064B Bedienungsanleitung

Honeywell

Honeywell TrueFRESH VNT5150H1000 Bedienungsanleitung

Honeywell

Honeywell HYF500E Bedienungsanleitung

Honeywell

Honeywell HT-216E Bedienungsanleitung

Honeywell

Honeywell HO-1100RE Bedienungsanleitung

Honeywell

Honeywell PERFECT WINDOW HR150 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung