Honeywell SEARCHLINE EXCEL EDGE Bedienungsanleitung

QUICK START

GUIDE

SEARCHLINE EXCEL™EDGE

Open Path Flammable Gas Detector

ENGLISH 3

DEUTSCH 13

FRANÇAIS 23

FRANÇAIS CANADIEN 33

NEDERLANDS 43

ITALIANO 53

ESPAÑOL 63

PORTUGUÊS 73

РУССКИЙ 83

英文 93

(3)

ENGLISHEN

Searchline Excel™Edge is a 3rd generation of Open Path Flammable Hydrocarbon Gas Leak Detectors

(OPFGD) designed to detect and alert to the presence of a range of ﬂammable hydrocarbon gases.

Searchline Excel Edge is an advanced Perimeter Monitoring OPFGD with coverage from 60 m to 330 m

(196 to 1,082 ft). Searchline Excel Edge consists of a cooperative transmitter/receiver pair that detects

the presence of a range of ﬂammable hydrocarbon gases in the line between them.

Searchline Excel Edge delivers maximum coverage and protection for perimeter and fence-line monitoring.

It comes with mounts and sunshades as a complete system and is supported by alignment and test

accessories.

Searchline Excel Edge provides local visual status indication as well as 4–20 mA with HART® and Modbus®

outputs as standard. It has a Bluetooth® interface for conﬁguration and maintenance using the Honeywell

Fixed Platform App on a suitable Bluetooth–enabled device.

Searchline ExcelEdge is ATEX andIECEx approved foruseineitherZone1(gas) or Zone21(dust)hazardous

areas as well as being cULus approved for use in Class I Division 1 or Class II Division 1 or Class III Division 1

locations.

Searchline Excel Edge is available in painted stainless steel and has two cable entries for easy wiring with

either M25 or 3/4” NPT options.

WARNING

1. The Searchline Excel Edge Open Path Flammable Gas Detector is certiﬁed for and intended for use

in potentially hazardous areas. Installation, operation and maintenance of the instrument must

meet requirements on safety and operation in hazardous areas.

2. Installation must be in accordance with the recognized standards of the appropriate authority in the

country concerned. For Europe see EN 6007914 and EN 60079292.

3. For installations in the UK, the Code of Practice SELECTION, INSTALLATION AND MAINTENANCE

OF ELECTRICAL APPARATUS FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES should be

strictly observed. General recommendations are given in BS EN 6007914 & IEC 6007914. Refer

to BS EN 60079292 & IEC 60079292 in the UK or the appropriate local or national regulations.

4. For installations in North America, the national Electrical Code (NFPA 70) or later issues should be

strictly observed.

5. The Searchline Excel Edge Open Path Flammable Gas Detector transmitters and receivers must

be properly earthed to protect against electrical shock and minimise electrical interference. For

electrical installation design considerations refer to chapter 6 Electrical Installation.

6. Operators must be fully aware of the action to be taken if the gas concentration exceeds an alarm

level.

7. Dismantling or repair of equipment should be carried out in the safe area only.

8.Testgasesmay betoxicand/orcombustible.RefertoMaterialSafetySheets for appropriatewarnings.

9. Do NOT drill holes in any housing as this will invalidate the explosion protection.

10. In order to maintain electrical safety, the instruments must NOT be operated in atmospheres

containing more than 21% oxygen.

11. Ensure that the bolts which secure ﬂame-proof enclosures are fully tightened. The securing bolts

used are made from a special certiﬁed grade of steel. Only bolts supplied by Honeywell Analytics

should be ﬁtted for this purpose.

12. Do NOT open the enclosure in the presence of an explosive atmosphere.

13. The transmitter unit contains high voltages when operational. These are discharged when the unit

is removed from its enclosure.

14. The conduit and cable glands ﬁtted to Searchline Excel Edge transmitter and receiver should NOT

be modiﬁed. If, however, it becomes necessary to make modiﬁcations they must comply with the

relevant national Codes of Practice.

15. The irradiance and power emitted by the Searchline Excel Edge transmitters is less than 5 mW/mm2

and 15 mW/mm2respectively. This is designated as eye safe.

(4)

INSTALLATION

CAUTION

1. A mobile device with Honeywell Fixed Platform App installed is a prerequisite for detector settings

adjustment made via the Bluetooth connection.

2. Commissioning or proof test of Searchline Excel Edge is not complete until the unit is tested to verify

that it functions according to its speciﬁcations.

WARNING

16. The equipment is NOT intended to be mounted onto surfaces which may act as sources of heating

or cooling.

17. Do NOT operate the instruments outside the temperature range stated in the Speciﬁcation section.

18. Do NOT open the front enclosures. Doing so will invalidate the warranty. Front enclosures may

be opened only for advised repair maintenance by an authorized and qualiﬁed person.

19. Do NOT modify or alter the construction of the product as essential safety and certiﬁcation

requirements may be invalidated.

20. Installation, set-up and maintenance must be conducted only by trained personnel. Refer to the

manual at all times.

21. Access to the interior of the product, when carrying out any work, must be conducted only by

trained personnel.

22. The plastic transport cap supplied must be replaced with suitably certiﬁed closers (such as glands

or stopping plugs) prior to commissioning. Failure to do so presents a potential source of ignition.

One certiﬁed stopping plug is supplied as standard.

23. Do NOT rely on the local visual indicator for safety related purposes.

NOTE:

If the last connection and synchronization between Honeywell Fixed Platform App and the server was

established more than 1 year previously, a caution message will be shown in the App with request to

establishanInternetconnection andrenewsecuritycertiﬁcate. This willNOTaffect instrument’soperation.

WHAT'S IN THE BOX?

1 Searchline Excel Edge receiver (box no.1)

1 Searchline Excel Edge transmitter (box no.2)

1 Universal Mounting Bracket

1 Plastic sunshade (stainless steel optional)

1 Antenna cover

1 Allen (hex) key, size 10

1 Allen (hex) key, size 8

1 Allen (hex) key, size 5

1 Allen (hex) key, size 1.5

1 Registration sheet

1 Quick Start Guide (this document)

CAUTION

1. Check the packaging for damage before opening. If the packaging shows signs of tearing, breakage or

other damage, immediately inform the transport company and the supplier. Document the damage in

an appropriate way (e.g., photographs).

2. Open the packaging carefully to avoid damaging the contents.

3. Examine the Searchline Excel Edge receiver and transmitter and the mount and sunshade for damage.

If you ﬁnd any item to be damaged in any way, immediately inform the transport company and the

supplier. Document the damage in an appropriate way (e.g., photographs).

(5)

CAUTION

(contd.)

4. In the case of damage:

a) Leave item(s) in the original packaging

b) Do not attempt repair, or operate the detector until the damage claim has been resolved with

the supplier.

5. Installation, set-up and maintenance must be conducted only by trained and authorized personnel.

6. Do NOT open the front enclosure. The warranty of a unit, whose front enclosure has been opened, is

invalidated. Front enclosures may be opened only for advised repair maintenance by an authorized

and qualiﬁed person.

7. Do NOT modify the front enclosure or component parts as this will compromise the hazardous location

certiﬁcation and invalidate the warranty. Front enclosures may be opened only for advised repair

maintenance by an authorized and qualiﬁed person.

8, Do NOT modify the construction of the detector in any way as this will invalidate the warranty.

9. Open and close the wiring compartment cover with care to avoid deformation.

10. Installation, set-up and maintenance must be conducted only by trained and authorized personnel.

11. Avoid water and dust ingress when opening the wiring compartment to protect the unshielded

electronic contacts.

12. Secure the detector when loosening bracket bolts. Unwanted release may cause injury.

13. Check mating surfaces prior to assembly (threads, O-rings). Ensure that they are clean and free of

contaminants.

14. Check the O-rings prior to assembly, replace if damaged with genuine parts.

15. Searchline Excel Edge is supplied without cable glands. Ensure that all cable entry threads are sealed

with an appropriate plug to eliminate water ingress and thread damage. At installation, the cable entry

transportation plugs must be removed and replaced with suitable cable glands, thread adapters or

blanking plugs to meet local hazardous location requirements.

16. Check suitability of the blanking plug for its end use on site, ensure it meets local and national

regulations.

17. Remove power from the Searchline Excel Edge instruments while installing wiring. Do NOT install

wires or set up wiring with power applied.

Searchline Excel Edge will normally be mounted at height, typically on a pole using supplied U–bolts and

covering the area to be protected. The supplied Universal Mounting Bracket allows mounting on a plate,

pole or other plant infrastructure. All bolts are retained to avoid loss during installation.

Searchline Excel Edge has two cable entries for easy wiring with either M25 or 3/4” NPT options. Wires are

terminated at the terminal connectors as per the wiring diagram. Spare wires must be suitably terminated.

Wiring must be in accordance with local, national and company regulations. Exposed or bare wires must

be avoided.

Refer to Technical Manual for instructions on mechanical and electrical installation.

You can download the Technical Manual from www.sps.honeywell.com.

CAUTION

If the 420 mA current loop is not used, a jumper must be connected between 420 mA+ (terminal 5)

and 24V DC+ (terminal 8) and a load resistor must be connected between 420 mA (terminal 6)

and 0V DC (terminal 9). It is recommended to use a 470 Ohm, 1/4 W resistor (250 to 400 Ωif HART

is required). With the 420 mA current loop conﬁgured this way the HART facility can still be used

with a HART handheld unit using terminals 20 and 21 inside the wiring compartment. A HART DTM

is available for Searchline Excel Plus and Searchline Excel Edge.

(6)

USER CONFIGURABLE OPTIONS

1. Detector ID

2. Operation mode

3. Inhibit level

4. Alarm 1 setpoint – modify

5. Alarm 2 setpoint – add

6. Warning level

7. Fault level

8. Over-range level

9. Alarm 1 level

10. Alarm 2 level

11. Proof test interval

12. LED mode

13. LED intensity

14. Inhibit timeout period

15. Set access code

16. Normal level

17. Alarm latch

18. Loop current mode

19. HART poll address

20. Fault relay

21. Alarm 1 relay

22. Alarm 2 relay

23. Gas reading output unit

24. Response time (1,2,3 sec)

The Honeywell Fixed Platform App allows to adjust the following user conﬁgurable options:

COMMISSIONING

CAUTION

1. A mobile device with Honeywell Fixed Platform App installed is a prerequisite for detector settings

adjustment made via the Bluetooth connection.

2. Commissioning or proof test of Searchline Excel Edge is not complete until the unit is tested to verify

that it functions according to its speciﬁcations.

1. Check that Searchline Excel Edge units are mounted and wired correctly. Refer to Installation section

of Technical Manual for instructions.

2. Check that Searchline Excel Edge units are optically aligned correctly. Refer to Alignment section of

Technical Manual for instructions.

3. Connect to Honeywell Fixed Platform App via Bluetooth.

4. Power up Searchline Excel Edge transmitter and receiver units.

5.Perform functional checkand4–20 mALoopIntegrityTest. RefertoCommissioningsectionofTechnical

Manual for instructions.

6. Check that Searchline Excel Edge units are conﬁgured as recommended by the relevant site survey

document.

7. If necessary, adjust detector settings utilising Honeywell Fixed Platform App.

8. Check that Searchline Excel Edge safety outputs are working properly. Refer to Maintenance section of

Technical Manual for instructions.

You can download the Technical Manual from www.sps.honeywell.com.

(7)

STATUS SIGNALLING

Searchline Excel Edge is equipped with a high visibility LED status indicator.

Refer to Operation section of Technical Manual for more information.

Operation

without

Bluetooth

Colour Scheme

Fault Yellow ﬂashing Default

Inhibit Yellow steady Default

Warning Yellow ﬂashing with

green alternating

Default

Normal Green steady Default

Normal Green ﬂashing Optional

Normal None Optional

Alarm Red ﬂashing Default

Over-range Red ﬂashing Default

WARNING

LED status indicator behaviour is conﬁgurable. If LED status indicator is conﬁgured differently from the

default setting, it may indicate states different to other outputs.

Operation

with

Bluetooth

Colour Scheme

Fault Yellow ﬂashing Default

Inhibit Yellow steady Default

Warning Yellow ﬂashing with

green alternating

Default

Normal Blue steady Default

Normal Blue ﬂashing Optional

Alarm Red ﬂashing Default

Over-range Red ﬂashing Default

Connecting Blue ﬂashing Default

Connected Blue steady Default

Warning Blue alternating Default

(8)

mA Loop Status Signaling

Mode Default Value (mA) Min Value

(mA) Max Value

(mA)

Discrete

Mode Proportional

Mode

Fault 1 0 3.6

Inhibit 2 1 3.6

Warning 3 1 4

Normal 4Proportional

to gas

concentration

420

Alarm 20 Not available 4 20

Over-

range

21 20 22

PERIODIC PROOF TEST

Searchline Excel Edge functionality can be veriﬁed using the Functional Test Filters (optional) or in

combination with the Honeywell Fixed Platform App.

Refer to Maintenance section of Technical Manual for instructions on how to perform Basic and

Advanced tests.

You can download Technical Manual from www.sps.honeywell.com.

(9)

SPECIFICATIONS

Primary Gases

(Performance

approved gases1, 2)

Searchline Excel Plus & Edge will respond to a wide range of Hydrocarbon Gases*:

Methane1,2, Ethane1, Propane1,2, Butane1, Pentane1, Hexane, Ethylene1, Propylene1,

1FM Performance Approved; 2DNV approved;

The default calibration is to Universal Hydrocarbon**.

Optional Gases Calibration to other gases is optional and should be consulted with Honeywell.

Range Methane 05 LEL.m / 0220,000 ppm.m

Ethane 05 LEL.m / 0120,000 ppm.m

Propane 05 LEL.m / 085,000 ppm.m

Butane 05 LEL.m / 070,000 ppm.m

Pentane 05 LEL.m / 055,000 ppm.m

Hexane 05 LEL.m / 050,000 ppm.m.

Ethylene 05 LEL.m / 0115,000 ppm.m

Propylene 05 LEL.m / 0100,000 ppm.m

Recommended

Alarm Setting

Low 1 LEL.m: High 3 LEL.m:

(and equivalent ppm.m) (and equivalent ppm.m)

Methane 44,000 ppm.m Methane 132,000 ppm.m

Ethane 24,000 ppm.m Ethane 72,000 ppm.m

Propane 17,000 ppm.m Propane 51,000 ppm.m

Butane 14,000 ppm.m Butane 42,000 ppm.m

Pentane 11,000 ppm.m Pentane 33,000 ppm.m

Hexane 10,000 ppm.m Hexane 30,000 ppm.m

Ethylene 23,000 ppm.m Ethylene 69,000 ppm.m

Propylene 20,000 ppm.m Propylene 60,000 ppm.m

Recommended

Minimum Alarm

Setting

0 to 0.5 LELm:

(and equivalent ppm.m)

Methane 22,000 ppm.m

Ethane 12,000 ppm.m

Propane 8,500 ppm.m

Butane 7,000 ppm.m

Pentane 5,500 ppm.m

Hexane 5,000 ppm.m

Ethylene 11,500 ppm.m

Propylene 10,000 ppm.m

Path Length Searchline Excel Edge: 60 m to 330 m (196 ft to 1082 ft)

Speed of Response T90 less than 3 seconds

Analog Output Signal 420 mA Normal operation, 1 mA Fault*,

2 mA Inhibit, 3 mA Warning, 21 mA Over-range,

*Searchline Excel Edge will indicate Fault after 30 s without signal. This value is

programmable. To comply with FM performance approval, the maximum value for Time to

Block is 200 s.

Environmental

Operating

Temperature

55 °C to +75 °C (67 °F to +167 °F); DNVGLCG0339 Location Class B

Storage Temperature

Range

55 °C to +75 °C (67 °F to +167 °F) DNVGLCG0339 Location Class B

Power Supply 24 Vdc nominal (18 Vdc to 32 Vdc)

* Searchline Excel Plus & Edge will respond to most hydrocarbon gases as most do absorb IR in the required wavelengths.

** Calibration to Universal Hydrocarbon covers a range of speciﬁc but different gases within one calibration that meets

the requirements of the performance standard.

(10)

SPECIFICATIONS

Power Consumption

(Average RMS)

Transmitter, for ambient operating temperature:

55°C (67°F) to 30°C (22°F) 11.8 W

30°C (22°F) to +30°C (+86°F) 5.6 W

above +30°C (+86°F) 3.8 W

Receiver, for ambient operating temperature:

55°C (67°F) to 30°C (22°F) 7.4 W

30°C (22°F) to +30°C (+86°F) 4.8 W

above +30°C (+86°F) 3.0 W

See Electrical Installation in Technical Manual for full details.

Cold Start / Heat-up

Power Consumption

Heat-up last approx. 20 min for both Transmitter and Receiver

Transmitter: 17 W

Receiver: 10 W for ambient temperature higher than 30 °C (22 °F)

15 W for ambient temperature lower than 30 °C (22 °F) (active heater)

Output Signals 4–20 mA with HART, Fault relay, Alarm 1 relay, Alarm 2 relay, Modbus, Bluetooth® (range up

to 20 m (66 ft), depends on mobile device and environmental conditions)

Relay Outputs Max. 32 Vdc/ac, max. 2 A resistive load

Inrush Current Transmitter: 0.5 A for less than 20 ms

Receiver: 0.3 A for less than 20 ms

Humidity 0–99 % RH Non-condensing . DNVGLCG0339 Location Class B

Pressure 91.5–105.5 kPa (915–1055 mBar, non-compensated)

Repeatability ±0.4 LEL.m:

(and equivalent ppm.m)

Methane ±17,600 ppm.m

Ethane ±9,600 ppm.m

Propane ±6,800 ppm.m

Butane ±5,600 ppm.m

Pentane ±4,400 ppm.m

Hexane ±4,000 ppm.m

Ethylene ±9,200 ppm.m

Propylene ±8,000 ppm.m

Temperature Drift

(55 °C to +75 °C)

(67 °F to +167 °F)

±0.2 LEL.m @ zero: ±0.5 LEL.m @ 3LEL.m:

(and equivalent ppm.m) (and equivalent ppm.m)

Methane ±8,800 ppm.m Methane ±22,000 ppm.m @ 132,000 ppm.m

Ethane ±4,800 ppm.m Ethane ±12,000 ppm.m @ 72,000 ppm.m

Propane ±3,400 ppm.m Propane ±8,500 ppm.m @ 51,000 ppm.m

Butane ±2,800 ppm.m Butane ±7,000 ppm.m @ 42,000 ppm.m

Pentane ±2,200 ppm.m Pentane ±5,500 ppm.m @ 33,000 ppm.m

Hexane ±2,000 ppm.m Hexane ±5.000 ppm.m @ 30,000 ppm.m

Ethylene ±4,600 ppm.m Ethylene ±11.500 ppm.m @ 69,000 ppm.m

Propylene ±4,000 ppm.m Propylene ±10.000 ppm.m @ 60,000 ppm.m

Warm-up Time Less than 5 minutes (operational), less than 1 hour (fully stabilised)

Internal Battery Cell TLH2450, 10-year lifetime (replaced only by authorized service)

Weight Searchline Excel Edge: Rx 6.1 kg (13.4 lbs), Tx 6.0 kg (13.2 lbs)

Universal Mounting Bracket: 3.1 kg (6.9 lbs) Stainless Steel

Mount Plate Adaptor: 3.71 kg (8.18 lbs) Stainless Steel

Dimensions Searchline Excel Edge transmitter and receiver: 103 mm dia x 325 mm x 180 mm

(4.06" dia x 12.8" x 7.09")

Universal Mounting Bracket: 165 mm x 165 mm x 130 mm (6.5" x 6.5” x 5.12")

Mount Plate Adaptor: 210 mm x 210 mm x 127 mm (8.23" x 8.23” x 5")

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell BW Technologies Clip Real Time Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlertQuattro 1 Bedienungsanleitung

Honeywell

Honeywell 04230-A-1001 Versionshinweis

Honeywell

Honeywell BW IntelliFlash GasAlertMax XT II Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung

Honeywell

Honeywell Midas Bedienungsanleitung

Honeywell

Honeywell MBeacon Bedienungsanleitung

Honeywell

Honeywell HON COCON 13 Bedienungsanleitung

Honeywell

Honeywell PHD6 Referenzhandbuch

Honeywell

Honeywell Sensepoint XRL Bedienungsanleitung

Honeywell

Honeywell Apex Versionshinweis

Honeywell

Honeywell ToxyPoint Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCD Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell BW Solo Bedienungsanleitung

Honeywell

Honeywell NOTIFIER VGS Series Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicroClip XT Bedienungsanleitung

Honeywell

Honeywell JTQJ-BF-01LM/BW Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell BW GasAlertQuattro Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Benutzerhandbuch

Honeywell

Honeywell Touchpoint 4 Bedienungsanleitung

Honeywell

Honeywell Searchline Excel Open-Path Versionshinweis

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Benutzerhandbuch

Honeywell

Honeywell FS20X Series Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung