Honeywell Sensepoint XRL Bedienungsanleitung

Sensepoint XRL

Fixed Gas Detector

Quick Start Guide

Read and understand the Sensepoint XRL Instruction Manaul before installing, operating or

servicing this product. These are available for download from the Honeywell Analytics website. Visit

.

1 Safety

Installation must be in accordance with the recognized standards of the appropriate authority in the

country and locality concerned.

2 Analog (mA) Output Versions

1) +24 V DC or 24 V AC 2) 0 V or 24 V AC

3) 4 to 20 mA 4) Common

3 Modbus RTU Output Versions

1) +24 V DC or 24 V AC 2) 0 V or 24 V AC

3) A 4) B

4 Securing the Detector to a Wall

,1&20&2

1. Determine where the detector is to be placed. Mark and drill

holes as required.

2. Secure the detector in its mounting position with suitable ﬁxings

appropriate to the mounting surface. Do not over-tighten.

5 Cable Connections

1. Unscrew the front cover counterclockwise until it is open.

2. Hold the handle of the main electronics module and pull it

outward with a steady force. Do not pull sharply.

3. Pull out the thread protector from the left cable entry, and

remove the blanking plug from the right by turning it

counterclockwise. If required, ﬁt the blanking plug to the unused

cable entry and tighten it.

4. Fit suitable cable glands or conduit appropriate to the

application and type of cable being utilized to the cable entries.

5. Feed the cable through the cable gland.

6. Pull the terminal blocks to remove them from the connector

module.

7. Connect cables to the terminal blocks, referring to the relevant

wiring diagram. Strip and insert the end of each wire into the

corresponding terminal hole. Using a ﬂat-blade terminal

screwdriver, tighten the terminal screw until the wire is secured.

Use a ferrule on the wire where necessary.

8. Replace the terminal blocks in their correct positions.

6 Ground Connections

Effective grounding is crucial to ensure stable Modbus

communications and to limit the effects of radio frequency

interference. A ground point is provided inside the housing. In order

to prevent false readings or alarms as a result of ground loops,

ensure that the shield of all cables are grounded at a single point,

preferably at the controller. Consideration should also be given to

how conduit and glands are also grounded.

NOTE

A connection for safety earth is provided at the top of the outside of the enclosure. This must be used to

connect the enclosure to electrical safety earth. Any earth regime must avoid earth loops.

7 Finalizing Installation

pujvtjv

1. Where used, tighten the sealing nut of the cable gland to secure

the cable.

2. Reﬁt the main electronics module to the connector module.

3. Replace the front cover by turning it clockwise ensuring that it is

tight.

4. Lock the front cover in position by tightening the grub screw.

8 Status Indicator

The detector features a status indicator on its front face.

Normal: The indicator ﬂashes GREEN every 20 seconds when the concentration

of the target gas is within normal range. The Normal indication can also be set

to steady green or Off.

Alarm:RED ﬂashes rapidly when the gas concentration is beyond the alarm-level

threshold.

Fault:YELLOW ﬂashes rapidly when the gas detector is in a fault state.

Bluetooth pairing:BLUE ﬂashes when Bluetooth® pairing between the gas

detector and a smartphone is in progress.

Bluetooth connected: Steady BLUE is lit when a Bluetooth connection is

established.

9 Connecting to a Detector via Bluetooth

To pair your smartphone with a speciﬁc detector, follow these steps:

1. Download Sensepoint App from Google Play Store. Install and launch the app.

2. Create and register a user account, and log on with the created account information.

3. To associate with the Sensepoint XRL gas detector, scan the QR code on the sheet included in

the box or enter its Activation Key.

4. Complete the installation of the detectors.

5. On the app’s home screen, tap DETECTORS to scan for available detectors.

6. Select a detector from the detector list to pair with it.

7. Look for the detector whose Status Indicator is ﬂashing blue.

8. Tap Conﬁrm Detector to pair with that detector. Otherwise, tap Return to list to select one of the

others.

For more information, please refer to the Sensepoint App manual.

When a Bluetooth® connection is established, the detector’s reading is displayed on the app

interface with the gas type and other information.

10 Speciﬁcations

Physical speciﬁcation

              

    

Power supply

      †

      ‡  

     

Maximum power consumption

         

         

Outputs§

         

   

Operating Environment

         

         

    ¶

     

    

    

    

Cable Gland

 

  

†mA versions: 11 to 32 VDC, Modbus versions: 9 to 32 VDC

‡20 to 27 VAC

§Dependent on version

¶Flammable catalytic versions: 10 to 90% RH. Operating the detector outside of this range may result in increased drift and a

reduction in detector accuracy.

11 Certiﬁcations

• ATEX (DEMKO 17 ATEX 1872X)

II 2 GD

Ex db IIC T6 Gb

Ex tb IIIC T85°C Db

Tamb −40 to +65°C

• IECEx (IECEx UL 17.0038X)

Ex db IIC T6 Gb

Ex tb IIIC T85°C Db

Tamb −40 to 65°C

• cULus

Class I, Division 1 & 2, Groups B, C and D

Class II, Division 1 & 2, Groups E, F and G

Class I, Zone 1, AEx db IIC T6

Zone 21, AEx tb IIIC T85°C, IP6X

Ex db IIC T6 GbX

Ex tb IIIC T85°C DbX

Tamb −40 to +65°C, Temp Code T6

Keep this manual for later use. For full operating instructions:

3017M5034_1 HAA170035 

Andere Handbücher für Sensepoint XRL

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell MultiRAE Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Benutzerhandbuch

Honeywell

Honeywell SPM Flex Bedienungsanleitung

Honeywell

Honeywell 201T Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell ToxyPoint Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert MicroClip XT Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK SZSK-SMG Series Bedienungsanleitung

Honeywell

Honeywell Notifier NCO-10 Bedienungsanleitung

Honeywell

Honeywell BW Icon Bedienungsanleitung

Honeywell

Honeywell BW MaxXT II Bedienungsanleitung

Honeywell

Honeywell E3Point E3DA Bedienungsanleitung

Honeywell

Honeywell 3000 MkIII Series Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL EDGE Bedienungsanleitung

Honeywell

Honeywell RAEGuard 3 Bedienungsanleitung

Honeywell

Honeywell Searchline Excel Open-Path Versionshinweis

Honeywell

Honeywell BW RigRat Bedienungsanleitung

Honeywell

Honeywell BW IntelliFlash GasAlertMax XT II Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Benutzerhandbuch

Honeywell

Honeywell Sensepoint XCL Bedienungsanleitung

Honeywell

Honeywell RAEGuard Lite Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung