Honeywell Sensepoint XCL Bedienungsanleitung

Gas Detec on

Sensepoint XCL

Fixed Gas Detector

Quick Start Guide

Sensepoint XCL

Fixed Gas Detector

Quick Start Guide

Read and understand the Sensepoint XCL Operating Instructions before installing, operating or servicing this product.

These are available for download from the Honeywell Analytics website. Visit www.honeywellanalytics.com.

Safety

Installation must be in accordance with the recognized standards of the appropriate authority in the country and locality

concerned.

Analog (mA) Output Versions

1) +24 V DC or 24 V AC 2) 0 V or 24 V AC

3) 4 to 20 mA 4) Common

Modbus RTU Output Versions

+24 V DC or 24 V AC 2)

0 V or 24 V AC

3) A 4) B

Relay Output

1) Normally closed (NC) 2) Common

3) Normally open (NO)

Securing the Back Box to a Wall

There are four screw positions in the rear of the back box for mounting purposes.

Punch the required screw positions or drill using a 4 mm drill.

Secure the back box in its mounting position with suitable ﬁxings appropriate to the

mounting surface. Do not over-tighten.

There are four cable entry knock-outs on three of the sides and rear face of the back

box. Drill or punch the entries as required.

Cable Connections

Fit suitable cable glands (included) or conduit ﬁttings to the opened cable entries.

Feed the cable through the cable gland.

Turn over the detector module and locate the terminal blocks on the back. Remove the

terminal blocks, pulling them toward the center of the module.

Connect the cable to the appropriate terminal block, referring to section 2 to 4

depending on the version. Strip and insert the end of each wire into the corresponding

terminal hole, and tighten the terminal screw, using a ﬂat-blade terminal screwdriver

until the wire is secured.

Replace the terminal blocks in their correct positions.

Ground Connections

Effective grounding is crucial to ensure stable Modbus communications and to limit the effects of radio frequency

interference. Ground points are provided inside the back box. In order to prevent false readings or alarms as a result of

ground loops, ensure that the shield of all cables are grounded at a single point, preferably at the controller.

Consideration should also be given to how conduit, glands and the internal earth plate are also grounded.

NOTE

Any earth regime must avoid earth loops.

Securing the Detector Module to the Back Box

Remove the front cover from the detector module to expose the retaining screws as

follows:

Pull the ﬂap on the bottom side to open it.

To unlock the front cover, insert a thin, straight tool, such as a small screwdriver,

into the hole to the right of the tube spigot.

While applying slight pressure to the tool, turn the cover counterclockwise until it

stops, and then lift it out.

Position the detector module onto the back box ensuring that the Status Indicator is in

the top left-hand corner when viewed from the front.

Tighten the four retaining screws using a No. 2 Phillips screwdriver to secure.

Where used, tighten the sealing nut of the cable gland to secure the cable. Refer to the

cable gland manufacturer’s instructions.

Replace the front cover by placing it into the detector module and rotate it clockwise

until it locks into position.

Remote Gassing Connection

If the gas detector is installed in an inaccessible location, such as overhead on a ceiling, connect a tube to the gas

detector for bump test.

•

For a temporary connection, open the ﬂap on the bottom side and

connect suitable tubing compatible with the gas type of the sensor to

the tube spigot.

•

For a permanent connection, remove the ﬂap, connect the tube

connector (available separately) to the spigot, and then connect a tube

to the tube connector. Secure the tube using a cable tie or small jubilee

clip, taking care not to over-tighten it.

Status Indicator

The detector features an external visual status indicator on its front face.

Normal: The indicator is lit GREEN

when the concentration of the target gas is within normal range.

The Normal indication can also be set to Conﬁdence Flash

or Off.

Alarm: RED

ﬂashes rapidly when the gas concentration is beyond the alarm-level threshold.

Fault: YELLOW

ﬂashes rapidly when the gas detector is in a fault state.

Bluetooth pairing: BLUE

ﬂashes when Bluetooth® pairing between the gas detector and a

smartphone is in progress.

Bluetooth connected: Steady BLUE

is lit when a Bluetooth connection is established.

Connecting to a Detector via Bluetooth (Bluetooth versions only)

To pair your smartphone with a speciﬁc detector, follow these steps:

Download Sensepoint App from Google Play Store. Install and launch the app.

Create and register a user account, and log on with the created account information.

To associate with one or more gas detectors, scan the QR code on the sheet included in the box or enter its

Activation Key.

Complete the installation of the detectors.

On the app’s home screen, tap DETECTORS to scan for available detectors.

Select a detector from the detector list to pair with it.

Look for the detector whose Status Indicator is ﬂashing blue.

Tap Conﬁrm Detector to pair with that detector. Otherwise, tap Return to list to select one of the others.

For more information, please refer to the Sensepoint App manual.

When a Bluetooth® connection is established, the detector’s reading is displayed on the app interface with the gas type

and other information.

Speciﬁcations

Physical speciﬁcation

Dimension 113 mm × 113 mm × 59 mm (4.4 × 4.4 × 2.3 in)

Weight 500 g (1.1 lb)

Power supply

DC input voltage (nominal) 24 V DC†

AC input voltage (nominal) 24 V AC‡, 50/60 Hz

Inrush current

Less than 850 mA

Maximum power consumption

mA Versions < 1.2 W (toxic), < 1.7 W (ﬂammable)

Modbus versions < 0.7 W (toxic), < 1.2 W (ﬂammable)

Relay versions Additional 0.6 W

Outputs§

Analog output 0 to 22 mA sink or source (conﬁgurable)

Digital output Modbus RTU

Relay output 2 × dry contact relays for fault and alarm signalling. Rated at 5 A @ 24 V DC, 5 A @ 240 V AC

Operating Environment

Operating temperature −20 to 50°C (−4 to 122 °F)

Storage temperature 0 to 30°C (32 to 86 °F)

Humidity 0 to 99% (non-condensing)¶

Atmospheric pressure 90 to 110 kPa

Ingress protection IP65 / Type 4 (in accordance with NEMA 250)

Installation category II (UL/CSA/IEC/EN 61010-1)

Pollution degree 2 (UL/CSA/IEC/EN 61010-1)

Cable Gland

Inner knock-out M20 or ½ NPT

Outer knock-out

M25 or ¾ NPT

Gas Test Tubing

Inner diameter 4 or 6 mm

Outer diameter 6 or 8 mm

† mA versions: 11 to 32 VDC, Modbus versions: 9 to 32 VDC

‡ 20 to 27 VAC

§ Dependent on version

¶ Flammable catalytic versions: 10 to 90% RH. Operating the detector outside of this range may result drift and a

decrease detector accuracy.

3017M5000_1 HAA170019

Find out more

www.honeywellanalytics.com

Contact Honeywell Analytics:

Americas

Honeywell Analytics, Inc.

405 Barclay Blvd.

Lincolnshire, IL 60069

USA

Tel: +1 847 955 8200

Toll free: +1 800 538 0363

Fax: +1 847 955 8210

detectgas@Honeywell.com

Europe, Middle East, Africa

Life Safety Distribution GmbH

Javastrasse 2

8604 Hegnau

Switzerland

Tel: +41 (0)44 943 4300

Fax: +41 (0)44 943 4398

gasdetection@honeywell.com

Asia Paciﬁc, India

Honeywell Analytics Asia Paciﬁc, Co., Ltd.

7F SangAm IT Tower

434 Worldcup Buk-ro, Mapo-gu

Seoul 03922

South Korea

Tel: +82 (0)2 6909 0300

Fax: +82 (0)2 2025 0388

India Tel: +91 124 4752700

China Tel: +86 10 5885 8788 3000

analytics.ap@honeywell.com

www.honeywell.com

For full operating

instructions：

Andere Handbücher für Sensepoint XCL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell 3000 MkIII Series Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell BW Flex Series Bedienungsanleitung

Honeywell

Honeywell MBeacon Bedienungsanleitung

Honeywell

Honeywell BW Technologies Clip Real Time Bedienungsanleitung

Honeywell

Honeywell GasAlertMicro 5 Series Bedienungsanleitung

Honeywell

Honeywell Touchpoint 4 Bedienungsanleitung

Honeywell

Honeywell MultiRAE Series Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert Quattro Bedienungsanleitung

Honeywell

Honeywell Midas Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert MicroClip XT Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK Bedienungsanleitung

Honeywell

Honeywell PHD6 Referenzhandbuch

Honeywell

Honeywell 201T Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell NOTIFIER VGN Series Bedienungsanleitung

Honeywell

Honeywell MultiRAE Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicro Bedienungsanleitung

Honeywell

Honeywell BW Clip Real Time Bedienungsanleitung

Honeywell

Honeywell BW RigRat Bedienungsanleitung

Honeywell

Honeywell BW MaxXT II Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung