Honeywell MultiRAE Series Bedienungsanleitung

Honeywell MultiRAE Series™

Portable Multi-gas Monitor

Table of Contents

Honeywell MultiRAE Series™ 1

Safety 1

Features Comparison 8

Standard Contents 11

General Information 14

Key Features 15

User Interface 19

Display Overview 19

Screen Display for Various Numbers of Active Sensors 26

Menus 27

Wireless Control and Submenus 32

Point-To-Point Wired Connection 35

Using Safety Suite Device Configurator (SSDC) to Set P2P Operation 35

Connecting a MultiRAE to a PC to Enable Point-To-Point Operation 39

Charging with the MultiRAE Desktop Cradle 41

Automatic PID Cleaning 42

Charging with The Travel Charger 43

Carrying the MultiRAE In A Vehicle 43

Charging with the AutoRAE 2 46

Replacing a Battery 46

Charging Batteries with A MultiRAE Battery Charger 47

Battery States 49

Alkaline Battery Pack 49

Turning the MultiRAE On and Off 52

Fast Access to Safety Suite Device Configurator (SSDC) 52

Turning the MultiRAE On 52

Turning the MultiRAE Off 53

Honeywell MultiRAE Series™ 2 User Manual

Testing Alarm Indicators 53

Glance Mode 53

Pump Status 54

Calibration Status 55

Bump Status 55

Toggle Display: Alternating Between Correction Factor and Reading 55

Enabling Benzene Operation & Sep-Tube Cartridge Tutorial 56

Modes of Operation 59

Hygiene Operation Mode 59

Search Operation Mode 59

Benzene-Specific Mode 59

Basic User Mode 66

Advanced User Mode 66

Programming 68

Enter Programming in Advanced Mode 68

Enter Programming in Basic Mode 69

Menus and Submenus 70

Policy Enforcement 114

Setting Policy Enforcement 114

Deactivating Policy Enforcement 118

Calibration and Testing 121

Manual Alarms Test 121

Bump Testing and Calibration 121

Zero/Fresh Air Calibration 126

Span Calibration 127

Three-Point Calibration for Enhanced Linearity with Extended- Range And ppb

PID Sensors 128

MultiRAE Pro Normal & Gamma Operation 134

Normal Mode for Simultaneous Radiation & Gaseous Threat Measurements 134

Gamma Radiation-Only Measurement Mode 134

Honeywell MultiRAE Series™ 3 User Manual

Datalog Transfer, Monitor Configuration, and Firmware Upgrades

Via Computer 138

Downloading Datalogs and Performing PC-Based Instrument Configuration and

Firmware Upgrades 139

Maintenance 142

Removing/Installing the Rubber Boot 142

Replacing the Filters 143

Replacing the Gas Inlet Adapter 144

Removing/Cleaning/Replacing Sensor Modules 144

Removing/Cleaning/Replacing A PID (Pumped Versions Only) 145

Replacing the Pump 147

Alarms Overview 149

Alarm Signals 149

Changing the Alarm Mode 149

Alarm Signal Summary 150

Troubleshooting 155

Pump Stall Threshold Adjustment 159

Entering Diagnostic Mode to Set the Pump Stall Threshold 159

Selecting the Pump Stall Threshold Method 160

Setting Pump Stall Threshold Values – Dynamic Method 160

Setting Pump Stall Threshold Values – Static Method 162

Configuring Wi-Fi Communication 166

Setting Wi-Fi Communication Parameters in Safety Suite Device Configurator

(SSDC) 166

Configuring Messaging 171

Configuring BLE 172

BLE Modes 172

Specifications 179

Honeywell MultiRAE Series™ 4 User Manual

Appendix 186

Alarm Limits 186

Sensors’ information 188

Honeywell MultiRAE Series™ 5 User Manual

IMPORTANT!

MultiRAE-series instruments use instrument firmware version 1.52/sensor firmware version 1.52.

MultiRAE series device uses instrument FW 1.31/ sensor FW 1.08A

MultiRAE lite with Wi-Fi option uses instrument FW 1.36/ sensor FW 1.36

Note: Fws 1.36 are not compatible with MultiRAE series device not using Wi-Fi module (and vice

and versa).

IMPORTANT! BUMP TEST THE MONITOR BEFORE EACH DAY’S USE

Prior to each day’s use, every gas detection monitor should be bump tested to confirm the

response of all sensors and activation of all alarms by exposing the monitor to a

concentration of target gas that exceeds the low alarm set point. A bump test is also

recommended if the monitor has been subjected to physical impact, liquid immersion, an

Over Limit alarm event, or custody changes, or anytime the monitor’s performance is in

doubt.

To ensure greatest accuracy and safety, only bump test and calibrate in a fresh air

environment.

The monitor should be calibrated every time it does not pass a bump test, but no less

frequently than every six months, depending on use and exposure to gas and contamination,

and its operational mode.

• Calibration intervals and bump test procedures may vary due to national legislation.

• Honeywell recommends using calibration gas cylinders containing the gas that is

appropriate to the sensor you are using, and in the correct concentration.

MultiRAE series device uses instrument FW 1.31/ sensor FW 1.08A

MultiRAE lite with Wi-Fi option uses instrument FW 1.36/ sensor FW 1.36

Honeywell MultiRAE Series™ 1 User Manual

CHAPTER

1Safety

CAUTION! Fws 1.36 are not compatible with MultiRAE series device not using Wi-Fi module

(and vice and versa).

WARNINGS

Read Before Operating

This manual must be carefully read by all individuals who have or will have the responsibility of

using, maintaining, or servicing this product. The product will perform as designed only if it is

used, maintained, and serviced in accordance with the manufacturer’s instructions.

CAUTION!

Never operate the monitor when the cover is removed. Remove the monitor rear cover or battery

only in an area known to be non-hazardous.

ANY RAPID UP-SCALE READING FOLLOWED BY A DECLINING OR ERRATIC READING MAY

INDICATE A GAS CONCENTRATION BEYOND UPPER SCALE LIMIT, WHICH MAY BE

HAZARDOUS.

TOUTE LECTURE RAPIDE ET POSITIVE, SUIVIE D’UNE BAISSE SUBITE AU ERRATIQUE DE LA

VALEUR, PEUT INDIQUER UNE CONCENTRATION DE GAZ HORS GAMME DE DÉTECTION QUI

PEUT ÊTRE DANGEREUSE

ONLY THE COMBUSTIBLE GAS DETECTION PORTION OF THIS INSTRUMENT HAS BEEN

ASSESSED FOR PERFORMANCE.

UNIQUMENT, LA PORTION POUR DÉTECTOR LES GAZ COMBUSTIBLES DE CET INSTRUMENT

A ÉTÉ ÉVALUÉE.

CAUTION: BEFORE EACH DAY’S USAGE, SENSITIVITY OF THE LEL SENSOR MUST BE TESTED

ON A KNOWN CONCENTRATION OF METHANE GAS EQUIVALENT TO 20 TO 50% OF FULL-

SCALE CONCENTRATION. ACCURACY MUST BE WITHIN 0 AND +20% OF ACTUAL.

ACCURACY MAY BE CORRECTED BY CALIBRATION PROCEDURE.

ATTENTION: AVANT CHAQUE UTILISATION JOURNALIERE, VERIFIER LA SENSIBILITE DU

CAPTEUR DE LIE AVEC UNE CONCENTRATION CONNUE DE METHANE EQUIVALENTE DE 20

A 50% DE LA PLEINE ECHELLE. LA PRECISION DOIT ETRE COMPRISE ENTRE 0 ET 20% DE

LA VALEUR VRAIE ET PEUT ETRE CORRIGEE PAR UNE PROCEDURE D’ETALONNAGE.

CAUTION: HIGH OFF-SCALE READINGS MAY INDICATE AN EXPLOSIVE CONCENTRATION.

Honeywell MultiRAE Series™ 2 User Manual

ATTENTION: DES LECTURES HAUTES ET HORS D’ECHELLE PEUVENT INDIQUER DES

CONCENTRATIONS DE GAZ INFLAMMABLES

CAUTION: Substitution of components may impair intrinsic safety.

Note: Users are recommended to refer to ISA-RP12.13, Part II-1987 for general information on

installation, operation, and maintenance of combustible gas detection instruments.

The MultiRAE multi-gas detector must be calibrated if it does not pass a bump test, or at least

once every 180 days, depending on use and sensor exposure to poisons and contaminants.

SPECIAL CONDITIONS FOR SAFE USE

1. The PGM-62xx shall only be fitted with Honeywell Battery Pack type M01-3053-000,

M01-3055-000, or Battery Adapter M01-3054-000 fitted with Duracell MN1500

batteries.

2. The PGM62xx shall only be charged outside hazardous areas.

3. No precautions against electrostatic discharge are necessary for portable equipment

that has an enclosure made of plastic, metal, or a combination of the two, except where

a significant static-generating mechanism has been identified. Activities such as placing

the item in a pocket or on a belt, operating a keypad or cleaning with a damp cloth, do

not present a significant electrostatic risk. However, where a static-generating

mechanism is identified, such as repeated brushing against clothing, then suitable

precautions shall be taken, e.g., the use of anti-static footwear.

The model PGM62xx is certified according to the IECEx scheme, ATEX and cCSAus (for US and

Canada). PGM62xx is intrinsically safe and may be used in hazardous locations.

SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY.

MARKING

The product is marked with the following information:

HONEYWELL

700 Mint St.

Charlotte, NC 28202, USA

Type PGM62x0, PGM 62x6, PGM 62x8

Honeywell MultiRAE Series™ 3 User Manual

Serial No/matrix: XXX-XXXX-000

IECEx SIR 11.0069X,

Ex ia IIC T4 Ga

Ex ia I Ma

(PGM62x0/PGM62x6)

Ex ia d IIC T4 Gb

Ex ia I Ma

(PGM62x8)

2460 SIRA

11ATEX2152X

II 1G Ex ia IIC T4

I M1 Ex ia I Ma

(PGM62x0/PGM62x6)

II 2G Ex ia d IIC T4

I M1 Ex ia I Ma

(PGM62x8)

Exia Cl I,

Dv 1

Gr. A, B, C, D,

T4;

Cl II, Dv 1 Gr.

E, F, G; T85ºC

C22.2 No

152-1984

ISA-12.13.01-

2000

IECEx TSA 13.0021X /

ANZEx 13.3023X

Ex ia IIC T4 Ga

Ex ia I Ma

(PGM62x0/PGM62x6)

Ex ia d IIC T4 Gb

Ex ia I Ma

(PGM62x8)

Warnings: Understand manual first before operating.

Warning:Do not change batteries in hazardous location.

Do not mix old/new or different type of batteries

PGM62x0: Use only Honeywell battery pack.

PGM62x6/62x8: Use only Honeywell battery pack, PN: M01-3053-000, M01-3055-000, or

M01-3054-000.

Um: 20V

-20º C ≤ Tamb ≤ +50º C

Honeywell MultiRAE Series™ 4 User Manual

FCC Part 15 Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Operation Area and Conditions

Hazardous Areas classified by Zones

PGM62x0/PGM62x6are intended to be used in hazardous areas zone 0, zone 1 or zone 2,and

PGM62x8 in hazardous areas zone 1 or zone 2 within the temperature range of -20º C to +50º

C, where gases of explosion groups IIA, IIB or IIC and T4 may be present.

Hazardous Areas classified by Divisions

PGM62x0/PGM62x6/PGM62x8are intended to be used in hazardous areas classified for Class

I &II Div. 1 or 2, within the temperature range of -20º C to +50º C, where gases of explosion

groups A, B, C, D, T4; Groups E, F, G; T85°C.

WARNINGS:

1. NDIR sensors shall not be installed in PGM62x0 or PGM 62x6 models.

2. NDIR LEL sensors shall not be installed in PGM62x8 diffusion models bearing cCSAus logo.

Proper Product Disposal at End of Life

The EU Directive 2012/19/EU: Waste Electrical and Electronic Equipment (WEEE)

This symbol indicates that the product must not be disposed of as general industrial or

domestic waste. This product should be disposed of through suitable WEEE disposal facilities.

For more information about disposal of this product, contact your local authority, distributor, or

the manufacturer.

Recommended Storage Conditions

Storage Temperature: 0° C to 20° C (32° F to 68° F)

Storage Humidity:15% to 90% RH (relative humidity), non-condensing; preferred 30% to

70% RH

0% RH preferred sealed storage for PID and NDIR sensors

Storage Pressure: 90 to 110kPa

Storage Life: 6 months in sealed container (no air)

Honeywell MultiRAE Series™ 5 User Manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell Midas Bedienungsanleitung

Honeywell

Honeywell Notifier VGS-EXP Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicroClip XT Bedienungsanleitung

Honeywell

Honeywell GasAlertMicro 5 Series Bedienungsanleitung

Honeywell

Honeywell Signalpoint Pro Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell BW Technologies GasAlert MicroClip XT Bedienungsanleitung

Honeywell

Honeywell SPM Flex Bedienungsanleitung

Honeywell

Honeywell PHD6 Referenzhandbuch

Honeywell

Honeywell XP Series Gebrauchsanweisung

Honeywell

Honeywell BW Technologies GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell BW Solo Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicroClip XT Bedienungsanleitung

Honeywell

Honeywell Notifier NCO-10 Bedienungsanleitung

Honeywell

Honeywell BW MaxXT II Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCL Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Benutzerhandbuch

Honeywell

Honeywell AreaRAE Plus Bedienungsanleitung

Honeywell

Honeywell BW Icon Bedienungsanleitung

Honeywell

Honeywell ToxyPoint Bedienungsanleitung

Honeywell

Honeywell Gamewell-FCI E3 Series Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell BW Clip Real Time Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung