Honeywell BW Flex Series Bedienungsanleitung

USER

MANUAL

Honeywell BW ™ Flex Series

Portable Multiple Gas Detector

M05-4002-003 EN-Rev. A

Table Of Contents

Safety 4

Introduction 5

Product Description 5

Standards and Certifications 5

What's in the Box 7

Overview 7

Display Elements 8

Operations 9

Out of the Box First Run 9

Set Language, Time, and Date 9

Activate the Detector 11

Self Test 11

Deactivate the Detector 12

Common Button Operations 12

Bluetooth Pairing 13

Calibration 14

Bump Test 23

Force Calibration and Bump 30

Zero Calibration 30

Capture Real Time Reading 30

Configure the detector Settings via DC 31

Maintenance 33

Clean the Detector 33

Charge the Battery 33

Update Firmware 36

Replace the Belt Clip or Klick Fast Stud 37

Replace the Sensor Filter 38

Replace a Sensor 39

BW Flex Series 2 User Manual

Sensor Poisons and Contaminants 41

Sensor Specifications 42

General Specifications 43

Troubleshooting 44

DataLogs and Event Logs 46

Alarms 47

Combustible Sensor Information 49

Filtered and Unfiltered Catalytic Bead Combustible (LEL) Sensor Information 50

User Preferences 53

Replacement Parts 56

Accessories 57

Security Information 58

BW Flex Series 3 User Manual

Additional Information 41

Safety

WARNINGS

lThe BW Flex Series detector with LEL-IR sensor (PN with W5) will not detect some

combustible gases like Hydrogen or Acetylene. For detectable combustible gases,See

"Combustible Sensor Information" on page49 for more information. If your application has

one or more of these hazards, please consult Honeywell Analytics to determine the best

solution.

lHigh off-scale LEL readings may indicate an explosive concentration.

CAUTION

lThe detector is a personal safety Device. It is your responsibility to respond properly to

lthe alarm.

lFor safety reasons, this equipment must be operated and serviced by qualified personnel

only.

lThe Li-ion battery in this product presents a risk of fire, explosion, and chemical burn if

misused. Do not disassemble, incinerate, or heat above 212°F (100°C). Batteries exposed to

heat at 266°F (130°C) for 10 minutes can cause fire and explosion. Batteries must only be

charged in a safe area free of hazardous gas.

lDeactivating the detector by removing the battery pack may cause improper operation and

harm the detector.

lUse only Honeywell approved battery chargers such as the vehicle Charger.

lDo not use the Detector if it is damaged. Inspect the Detector before use. Look for cracks

and missing parts.

lHoneywell recommends bumping test the sensors before each day's use to confirm their

ability to respond to gas by exposing the detector to a gas concentration that exceeds the

alarm setpoints. Manually verify that the audible and visual alarm activate. Calibrate if the

readings are not within the specified limits.

lProtect the catalytic combustible sensor from exposure to lead compounds, silicone, and

chlorinated hydrocarbons. Although certain organic vapors (Such as leaded gasoline and

halogenated hydrocarbons) may temporarily inhibit sensor performance, in most cases, the

sensor will recover after calibration.

lHoneywell recommends the catalytic combustible sensor be checked with a known

concentration of calibration gas after any known exposure to catalytic contaminants ot

poisons (sulfur compounds, silicons vapors, halogenated compounds, etc.).

lThe catalytic combustible sensor is factory calibrated to 50% LEL methane. If monitoring a

different combustible gas in the % LEL range, calibrate the sensor using the appropriate gas.

BW Flex Series 4 User Manual

CHAPTER

1Introduction

Learn what you need to know about the Honeywell BW™ Flex Series Gas Detector before

operating.

Product Description

The Honeywell BW™ Flex Series gas detector warns of hazardous gas at levels above user-defined

alarm setpoints. The detector can monitor up to four gases at a time.

Standards and Certifications

IECEx: IECEx SIR 20.0020X

With IR sensor installed: Ex ia op is I Ma, Ex ia op is IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

With LEL sensor installed: Ex da ia I Ma, Ex da ia IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

With IR and LEL sensor installed: Ex da ia op is I Ma, Ex da ia op is IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

Without IR and LEL sensor installed: Ex ia I Ma, Ex ia IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

ATEX: Sira 20ATEX2012X

With IR sensor installed:

I M1 Ex ia op is I Ma, -40°C≤ Tamb ≤ 60°C

II 1G Ex ia op is IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

With LEL sensor installed:

I M1 Ex da ia I Ma, -40°C≤ Tamb ≤ 60°C

II 1G Ex da ia IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

BW Flex Series 5 User Manual

With IR and LEL sensor installed:

I M1 Ex da ia op is I Ma, -40°C≤ Tamb ≤ 60°C

II 1G Ex da ia op is IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

Without IR and LEL sensor installed:

I M1 Ex ia I Ma, -40°C≤ Tamb ≤ 60°C

II 1G Ex ia IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

Contains FCC ID: SU3RMBLED

Contains IC: 20969-RMBLED

CAN ICES-3(A)/NMB-3(A)

FCC Compliance statement

This Detector complies with part 15 of the FCC Rules. operation is subject to the following two

conditions: (1) This Detector may not cause harmful interference, and (2) this Detector must

accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital

Detector, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his

own expense.

BW Flex Series 6 User Manual

What's in the Box

1 Honeywell BW™ Flex Series gas detector

1 Battery (factory-installed)

1 USB charger

1 Calibration cap

1 Klick Fast stud

1 Quick Reference Guide

1 Tubing

Overview

1 Alarm LED 6 Sensor

2 IntelliFlash 7 Clip

3 Display 8 Certification, model and Serial Number

4 Button 9 Charging and IR connection Port

5 Beeper

BW Flex Series 7 User Manual

Display Elements

lBattery full

lBattery half

lStatic icon

lBattery low, Battery charging

lFlashing icon: battery critical;

Battery can’t be charged

lBLE connected

lBLE fault

lIR connected

lProfile mode

lAVV failed

lStealth mode

lSensor fault

lSensor EOL

lCal fail / due

lCal countdown

lPredictive Cal due

lBump fail / due

lBump countdown

lInert Mode

lPress and hold the button

lWait

lWarning

lPass

lFail

lBack

lNext

lInformation

lBump

lZero

lCalibration

lExit

BW Flex Series 8 User Manual

CHAPTER

2Operations

Learn what you can do with your Honeywell BW™ Flex Series Detector, from commissioning to

Calibration.

Out of the Box First Run

This operation is only executed the first time the detector is turned on.

1. Turn on the Detector. LEDs flash red, Sensors warm up, and the Detector performs the

following Self-Tests: Battery, Firmware, BLE, Sensors, and Bump and Calibration due date.

2. After completing the Self-Test, you are asked to set the detector up in four ways: Manually,

BLE, IR Link, and IntelliDoX.

3. Single-press the button to select a setup method.

4. Press and hold the button to initiate the selected method. For a detailed description of each

method, go to See "Set Language, Time, and Date" below for more information.

5. After the initial setup is complete, the IntelliFlash flashes green every fifteen seconds, and the

detector goes to the Regular mode. You are now ready to select any operation from the main

menu.

Note: We strongly recommend to review the Alarm Settings after Start-Up.

Set Language, Time, and Date

Configure the Language, time, and Date in a new detector on the first run setup.

There are four ways to set the Time Zone and Language in a new detector:

lManual configuration via onscreen instructions.

lVia Device Configurator (DC) on a mobile device.

lVia Safety Suite Device Configurator (SSDC) on a computer.

lVia an IntelliDoX Docking Module. For further reference see the IntelliDoX User Manual.

Configure the Detector Manually

1. Turn on the Detector and wait until you see the "Setup Manually" screen.

2. On the "Setup Manually" screen, press and hold the button. The Language selection menu is

displayed.

You can select from the following languages:

English, Deutsch, Español, French, Italian, Portuguese, Russian, Nederlands, Simplified

Chinese, Traditional Chinese, and Korean.

BW Flex Series 9 User Manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell Touchpoint Plus Bedienungsanleitung

Honeywell

Honeywell SPM Flex Bedienungsanleitung

Honeywell

Honeywell BW MaxXT II Bedienungsanleitung

Honeywell

Honeywell Rae Systems MeshGuard Kurzanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell Gamewell-FCI E3 Series Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Benutzerhandbuch

Honeywell

Honeywell BW GasAlertMicroClip XT Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung

Honeywell

Honeywell MultiRAE Bedienungsanleitung

Honeywell

Honeywell NOTIFIER VGN Series Bedienungsanleitung

Honeywell

Honeywell BW IntelliFlash GasAlertMax XT II Bedienungsanleitung

Honeywell

Honeywell HON COCON 13 Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Bedienungsanleitung

Honeywell

Honeywell ToxyPoint Bedienungsanleitung

Honeywell

Honeywell MultiRAE Series Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert Quattro Bedienungsanleitung

Honeywell

Honeywell BW Icon Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell BW Technologies GasAlertQuattro 1 Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCL Bedienungsanleitung

Honeywell

Honeywell BW Solo Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung