Honeywell DR 4300 Leitfaden

Form 43-DR-33-74 Page 1 of 3

Model DR 4300

Circular Chart Recorder

Replacement Instruction

Display Module Printed Circuit Assembly (51404459-501)

Document Number Form: 43-DR-33-74

Effective: 3/98

Supersedes: None

Kit Contents This Display Module Printed Circuit Assembly (PCA) Kit contains the

following parts:

•Display PCA

•#6 x 3/8 Plastite Screws (2)

•Cables (2)

Summary Enclosed are a new display module PCA and parts for your DR4300

recorder. Use the following procedure to install the new display module.

WARNING Never access components inside the case with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 43-DR-33-74

Component Location Refer to Figure 1 for the component locations and Table 1 for the

installation procedure.

24229

Screws

Display

ModulePCA

Cable

Pen 2

Cable

Pen 1

Figure 1 – Component Location

Kit Instruction, continued

Form 44-DR-33-74 Page 3 of 3

Installation Procedure Follow the procedure in Table 1 to install the new display module PCA in

your recorder.

Table 1 – Display Module Printed Circuit Assembly Installation

Step Action

1Power down the recorder. Open the chart door and swing the chart

plate out.

2 Note cable orientation before removing the two screws holding the

display module PCA to the top of the case.

3 Disconnect cable(s) from the back side of old PCA. Pull outward

on the connector’s end tabs then pull out the ribbon cable(s).

You can leave the cable(s) attached to J4 on the main PCA(s)

unless you are also replacing the cable. If you are replacing the

cable(s), disconnect each one from J4 on its specific PCA and

remove it, noting the routing layout.

4 Install the cable(s) on the new display PCA. Insert the cable in the

connector and push in on end of connector tabs to lock cable(s) in

place.

If you are replacing the cable(s), go to Step 5.

If you are using the existing cable(s), go to Step 6.

5 Feed the pen 1 ribbon cable behind the transmitter power

assembly, behind the Main PCA for pen 1 (right side of case) to its

J4 connector (upper right corner).

If applicable, run the pen 2 ribbon cable behind the transmitter

power assembly, behind the pen 1 Main PCA, bringing it to the J4

connector on the Main PCA for pen 2 (left side of case). This

ribbon should be on top of the pen 1 ribbon cable.

6 Secure the new display PCA to the case with the screws provided.

7 Close the chart plate and apply power. Check for normal display

indication.

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell 90DM4 Bedienungsanleitung

Honeywell

Honeywell MI Wireless Kurzanleitung

Honeywell

Honeywell SmartLine RMA800 Bedienungsanleitung

Honeywell

Honeywell E-Mon Class 6200 Bedienungsanleitung

Honeywell

Honeywell QA 10 DN 25 G I Bedienungsanleitung

Honeywell

Honeywell HG4930 Bedienungsanleitung

Honeywell

Honeywell FE260 Bedienungsanleitung

Honeywell

Honeywell MicroMAX Pro Betriebsanleitung

Honeywell

Honeywell TWM 9000 Verdrahtungsschema

Honeywell

Honeywell EK205 Bedienungsanleitung

Honeywell

Honeywell Vertex M Bedienungsanleitung

Honeywell

Honeywell HEN04112 Bedienungsanleitung

Honeywell

Honeywell Minitrend Bedienungsanleitung

Honeywell

Honeywell RMA300-ME Bedienungsanleitung

Honeywell

Honeywell AirAlert 96d Handbuch

Honeywell

Honeywell Versatilis Signal Scout Bedienungsanleitung

Honeywell

Honeywell ENCAL 3000 Bedienungsanleitung

Honeywell

Honeywell APT4000PH Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW VORTEX 200 Verdrahtungsschema

Honeywell

Honeywell BendixKing KLR 10 Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW SONIC 2000 Beilage

Honeywell

Honeywell A700 Bedienungsanleitung

Honeywell

Honeywell Themis alpha EI2 Betriebsanleitung

Honeywell

Honeywell EWA600C-RF55C Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung