Honeywell DCP 50 Bedienungsanleitung

Sensing and Control

DCP 50

Digital Controller Programmer

Product Manual

57-77-25-17

3/00

Revision – 3/00

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as being free of defective materials and faulty

workmanship. Contact your local sales office for warranty information. If warranted goods are

returned to Honeywell during the period of coverage, Honeywell will repair or replace without

charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all

other warranties, expressed or implied, including those of merchantability and fitness for a

particular purpose. Specifications may change without notice. The information we supply is

believed to be accurate and reliable as of this printing. However, we assume no responsibility for

its use.

While we provide application assistance personally, through our literature and the Honeywell

web site, it is up to the customer to determine the suitability of the product in the application.

Sensing and Control

Honeywell

11 West Spring Street

Freeport, Illinois 61032

About This Document

Abstract

The purpose of this manual is to support the installation, configuration, and operation of the DCP 50

Digital Controller Programmer.

Contacts

World Wide Web

The following lists Honeywell’s World Wide Web sites that will be of interest to our customers.

Honeywell Organization WWW Address (URL)

Corporate http://www.honeywell.com

Sensing and Control http://www.honeywell.com/sensing

International http://www.honeywell.com/Business/global.asp

Telephone

Organization Phone Number

United States and Canada Honeywell 1-800-423-9883 Tech. Support

1-888-423-9883 Faxback

1-800-525-7439 Service

Asia Pacific Honeywell Asia Pacific

Hong Kong (852) 2829-8298

Europe Honeywell PACE, Brussels, Belgium [32-2] 728-2111

Latin America Honeywell, Sunrise, Florida U.S.A. (854) 845-2600

HONEYWELL DCP 50

DIGITAL CONTROLLER/PROGRAMMER

PRODUCT MANUAL

CONTENTS

1BASE MODE1-1

1.1DISPLAY SEQUENCE - NO PROGRAM RUNNING1-1

1.2STARTING A PROGRAM1-2

1.3 PUTTING A PROGRAM IN HOLD1-2

1.4RELEASING A PROGRAM FROM HOLD1-2

1.5ABORTING A PROGRAM1-2

1.6DISPLAY SEQUENCE - PROGRAM RUNNING1-3

1.7RaPID CONTROL FEATURE1-4

1.8 PRE-TUNE FEATURE 1-4

1.9 ENGAGING BOTH PRE-TUNE AND RaPID FEATURES1-5

1.10 INDICATION OF PRE-TUNE AND RaPID STATUS1-5

1.11VIEWING THE HARDWARE DEFINITION CODE1-6

1.12MANUAL CONTROL1-7

2INSTALLATION2-1

2.1UNPACKING PROCEDURE 2-1

2.2 PANEL-MOUNTING THE CONTROLLER2-1

(v)

2.3CONNECTIONS AND WIRING2-2

3PROGRAM DEFINITION MODE

- CREATING/EDITING A PROGRAM3-1

3.1ENTRY3-1

3.2CREATING A PROGRAM 3-2

3.3 DEFAULT VALUES AND ADJUSTMENT RANGES3-9

3.4EXIT FROM PROGRAM DEFINE MODE3-9

4CONTROLLER SET-UP MODE4-1

4.1PARAMETER DETAILS4-3

4.2 EXIT FROM CONTROLLER SET-UP MODE4-9

5MODBUS COMMUNICATIONS5-1

5.1INTRODUCTION5-1

5.2MODBUS FUNCTIONS SUPPORTED5-1

5.3MESSAGE FORMATS5-1

5.4PARAMETER NUMBERS5-7

5.5 PROFILER STATUS BYTE 5-11

5.6 PROFILER COMMANDS 5-11

6CONFIGURATION MODE6-1

6.1ENTRY INTO CONFIGURATION MODE6-1

6.2HARDWARE DEFINITION CODE6-1

6.3 OPTION SELECTION6-3

6.4CONFIGURATION MODE PARAMETERS6-4

6.5EXIT FROM CONFIGURATION MODE 6-9

(vi)

7INTERNAL LINKS AND SWITCHES 7-1

7.1REMOVING THE CONTROLLER PROGRAMMER FROM ITS HOUSING7-1

7.2REMOVING/REPLACING THE OUTPUT 2/OUTPUT 3 OPTION PCBs7-3

7.3REMOVING/REPLACING THE RS485 COMMUNICATIONS OPTION PCB

OR REMOTE RUN/HOLD OPTION PCB7-3

7.4REPLACING THE INSTRUMENT IN ITS HOUSING7-3

7.5 SELECTION OF INPUT TYPE AND OUTPUT 1 TYPE7-4

7.6OUTPUT 2 TYPE/OUTPUT 3 TYPE7-6

APRODUCT CODESA-1

BPRODUCT SPECIFICATIONB-1

CSUMMARY OF DISPLAYSC-1

(vii)

1BASE MODE

1.1DIS PL AYSEQUENCE - NO PROGRAM RUNNING

1-1

1.2 STARTING A PROGRAM

To start a program running:

1.3PUTTING A PROGRAM IN HOLD

A program can be put in Hold (i.e. frozen) at any time whilst it is running. The program

setpoint will stay at its value at the instant the program entered Hold until the

program is released (see Subsection 1.4) or aborted (see Subsection 1.5). To put a

program in hold, momentarily press the RUNkey. The RUNindicator will flash whilst

the program is in hold.

1.4RELEASING A PROGRAM FROM HOLD

To release a program currently in Hold, momentarily press the RUNkey. The RUN

indicator will then go ON continuously.

1 -2

1.5ABORTING A PROGRAM

To abort the current-running (or held) program, hold down the RUNkey for 5

seconds. The program will be aborted, the RUNindicator will go OFF and the

normal Controller functions will be resumed.

NOTE: When a program is aborted, the instrument returns to the Controller

setpont value. If a program is successfully completed, the Controller setpoint is

automatically set to the final setpoint value of the program. If it is desired to

restore the initial Controller setpoint value after the program is completed,

theis value should be used as the program's Final Setpoint Value.

1.6DISPLAY SEQ UENCE - PROGRAM RUNNING

1-3

Inhaltsverzeichnis

Andere Honeywell Netzwerk-Router Handbücher

Honeywell

Honeywell ST799 Bedienungsanleitung

Honeywell

Honeywell SDC 7-21 Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell WEB-645 Bedienungsanleitung

Honeywell

Honeywell DC313XXHGP2/BS Bedienungsanleitung

Honeywell

Honeywell Q7751A Bedienungsanleitung

Honeywell

Honeywell DHC 23 Bedienungsanleitung

Honeywell

Honeywell RAE Systems RAEPoint Bedienungsanleitung

Honeywell

Honeywell RedLINK THM6000R Bedienungsanleitung

Honeywell

Honeywell 5210 Bedienungsanleitung

Honeywell

Honeywell Q7751A Bedienungsanleitung

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell SDC Bedienungsanleitung

Honeywell

Honeywell MDENR100 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung