Honeywell Evohome Bedienungsanleitung

evohome

Installation Guide

The connected heating controller

evohome Controller

Digital Room Thermostat

(DTS92)

Wireless Relay Box (BDR91)

Wireless Cylinder Thermostat

Transceiver (CS92)

Wireless Cylinder Thermostat

Strap-on Sensor (CS92)

Wireless Cylinder Thermostat

Insertion Sensor (CS92)

Radiator Controller (HR92)

Radiator Controller (HR80)

Wireless OpenTherm Bridge

(R8810)

Mixing Valve Controller

(HM80)

Underﬂoor Heating Controller

(HCE80 or HCC80)

evohome Controller Wall Bracket

(ATF600)

evohome Controller Table Stand

(ATF800 )

Room Temperature Sensor

(HCW82)

Single Zone Thermostat

(Y87RF)

Room Temperature Sensor

(HCF82)

Hot Water Kit (ATF500DHW)

Icon key

evohome Installation Guide

Thanks for choosing evohome

evohome means more comfort, and

more control of the heating system. It’s

simple to install and easy to use.

Follow these instructions to set up the

evohome system. Devices that need to be

connected to the mains electricity supply

should be installed by a competent person.

Before you start

Make sure you have all the devices you need

for your system. If you used our ‘Design

your evohome system’ guide, match each

device to the room or zones in your plan.

It’s a good idea to carry out all the mains

electrical and other wiring work ﬁrst.

In this guide

Step 1: Wire up the heating system 3

Step 2: Set up your evohome Controller 9

Step 3: Power up and bind devices 13

Step 4: System test 29

Conﬁguration and modiﬁcation 37

Appendix 41

2Step 1: Wire up the heating system

Step 2: Set up your evohome Controller

Power up the evohome Controller, connect to a WiFi network and follow the on-screen instructions

for your system

Go to Installer Menu Go to Guided Conﬁguration Go to Home screen

You have…

a Connected Pack

Un-bound devices

You have…

an un-bound evohome

Controller

Un-bound devices

You have…

a Connected Pack

No additional devices

Step 3: Power up and bind devices

Power up all devices, including the battery powered ones,

and bind them to the evohome Controller

Step 1: Wire up your heating system

Connect all mains powered devices to the heating system

Step 4: Test the system

Check that all the devices are working properly

evohome Installation Guide

In this section

Wireless Relay Box (BDR91) 4

Wireless Cylinder Thermostat (CS92) 5

Mixing Valve Controller (HM80), Underﬂoor Heating Controller (HCE80/HCC80),

Opentherm Bridge (R8810) 7

Step 1: Wire up the

heating system

evohome communicates using wireless on a robust 868Mhz

signal that is unaffected by common remote controls or WiFi.

Some devices need mains power or to be connected to external

equipment and it's best to wire up these items ﬁrst to simplify the

binding process later in the setup. The evohome controller will

give on screen instructions when these should be powered up.

Before you power up your evohome Controller and install

the radiator controllers, it's best to install any devices which

are mains powered or need speciﬁc installation.

4Step 1: Wire up the heating system

Turn off at mains and

isolate the supply before

starting

!If you’re ﬁtting a Wireless Relay Box

(BDR91) to your boiler, zone valve or

Sundial valve

Mount the Wireless Relay Box on a non-

metal surface at least 30cm from your boiler,

other wireless devices or metal objects

Release the clip on the bottom to open the front cover

Follow the wiring diagram (see Appendix: Figures

5-10) to connect the Wireless Relay Box to your

boiler’s thermostat terminals, zone valve or sundial

valve, and to the mains electricity supply

Replace the cover

Refer to boiler instruction to locate the room thermostat terminals,

determine if the boiler required a permanent live supply.

Wireless Relay Box (BDR91)

BOILER

MINIMUM

30CM

REPLACE

FRONT

COVER

evohome Installation Guide

If you’re ﬁtting a Wireless Cylinder

Thermostat (CS92)

You will need to install the CS92 Transceiver and only

one of the two sensors (CS92 Strap-on Sensor or

CS92 Insertion Sensor).

To ﬁt the CS92 Strap-on Sensor

Cut away a section of cylinder insulation

slightly larger than the sensor unit

Clean the exposed cylinder surface

Place the sensor on the cylinder surface

and secure it using the ﬁxing strap – cut

the strap to size if it’s too long

Install the CS92 Transceiver in a suitable location

close enough for the cable from the sensor to reach

Connect the cable from the sensor

to the CS92 Transceiver

Position the sensor from one quarter to a

third of the way up the cylinder.

Wire to CS92 Transceiver

Wireless Cylinder Thermostat (CS92)

1/4 – 1/3

TOTAL

HEIGHT

45MM

80MM

MINIMUM

30CM

A x B Cy

6Step 1: Wire up the heating system

Wireless Cylinder Thermostat (CS92) continued

To ﬁt the CS92 Insertion Sensor

Fit in the cylinder immersion well with suitable ﬁttings to

provide strain relief and prevent accidental removal

If the sensor doesn’t ﬁt tightly in the immersion

well ﬁll the space with heat-conductive compound

to ensure maximum heat transfer

Install the CS92 Transceiver in a suitable location

close enough for the cable from the sensor to reach

Connect the cable from the sensor to the CS92 Transceiver.

The wires are polarity free, so can be connected

in any order. Provide appropriate strain relief

to this end of the sensor cable as well.

If this sensor is used in

an unvented hot water

storage application, the

cylinder manufacturer’s

instructions must be

followed to ensure

compliance with all

safety regulations.

If in doubt, contact the

cylinder manufacturer.

Wire to CS92 Transceiver

A x B Cy

evohome Installation Guide

If you’re ﬁtting a Mixing Valve

Controller (HM80), Underﬂoor

Heating Controller (HCE80/HCC80),

OpenTherm Bridge (R8810)

Refer to the installation instructions

supplied with each device

Mixing Valve Controller (HM80), Underﬂoor Heating

Controller (HCE80/HCC80), OpenTherm Bridge (R8810)

8Step 1: Wire up the heating system

Andere Handbücher für Evohome

Inhaltsverzeichnis

Andere Honeywell Netzwerk-Router Handbücher

Honeywell

Honeywell Q7751A Bedienungsanleitung

Honeywell

Honeywell SDC Bedienungsanleitung

Honeywell

Honeywell WEB-645 Bedienungsanleitung

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell SDC 7-21 Bedienungsanleitung

Honeywell

Honeywell ST799 Bedienungsanleitung

Honeywell

Honeywell MDENR100 Bedienungsanleitung

Honeywell

Honeywell DHC 23 Bedienungsanleitung

Honeywell

Honeywell DCP 50 Bedienungsanleitung

Honeywell

Honeywell 5210 Bedienungsanleitung

Honeywell

Honeywell Q7751A Bedienungsanleitung

Honeywell

Honeywell DC313XXHGP2/BS Bedienungsanleitung

Honeywell

Honeywell RedLINK THM6000R Bedienungsanleitung

Honeywell

Honeywell RAE Systems RAEPoint Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung