Honeywell HP300ULX Technisches Handbuch

HP300ULX

Access Control Power Supply/Charger

PN 52386:A 12/29/05 ECN 04-350

Honeywell

12 Clintonville Road

Northford, CT 06472

http://www.honeywellpower.com

Product Installation Document

This product follows under the UL1481 Fire Alarm Systems, UL603 Burglary Alarm Systems and UL294 Access Control

Systems. The HP300ULX unit is to be installed in a fail safe mode unless authorized by the local AHJ. This product must

be installed in compliance with Article 760 of the National Electrical Code, NFPA70, as well as NFPA72 National Fire

Alarm Code and all applicable local codes.

1 Description

The HP300ULX is a 12VDC or 24VDC power supply with AC fail and Battery fail supervision. The unit has not been

evaluated as elevator equipment, and is not authorized for bell output in Mercantile applications.

2 Specifications

1. Input voltage: 120VAC 60Hz; Current: 1.50A max.

2. Output Voltage: 12VDC or 24VDC, jumper selectable; Current: 2.5A continuous output maximum, 2.0A plus battery

charger (not supervised).

3. Fail safe dry contact output on AC Failure (within one minute).

4. Built-in charger for sealed lead acid or gel cell type batteries.

5. Instantaneous transfer to stand-by battery on AC failure.

6. Battery presence detection (within 1 minute)

7. Battery low disconnect at 9.90VDC or 19.90VDC.

8. High voltage disconnect at 15VDC or 30VDC.

9. Yellow LED (L3) indication for battery disconnected and battery low.

10. Fail safe dry contact output for Battery trouble (Fail Safe).

11. Battery polarity reversal protection.

12. Thermal overload and short circuit protection.

13. DC output PTC activated indication by Red LED (L2).

14. DC output failure indication by Red LED ( L4 ).

15. AC presence indication by Green LED ( L1 ).

16. DC output indication by Red LED ( L5 ).

17. Battery Leads included.

18. Power Board Dimensions: 5”L x 3.9”W x 1.5”H.

19. Enclosure Dimension: 17”L x 13.5”W x 4.75”H. Accommodates two 12 Volt 12AH batteries. When using larger

batteries, a UL approved enclosure must be used.

3 Installation Instructions

1. Mounting

The power supply should be installed in accordance with all Governing National Electrical and Local Codes. Mount the

power supply securely in the desired location using the four (4) mounting holes.

2. Power Supply Input Connection

Continued on next page...

2HP300ULX Installation Document P/N 52386:A 12/29/05

Before connecting power, review the entire wiring diagram for correct installation (see Fig. 1). With the AC power

disconnected, connect 120VAC to the Fuse Block as follows; L=Black (HOT), N=WHITE (Neutral), G=GREEN

(Ground). Select the output voltage 12VDC or 24VDC using Jumper J1 of the Power Board J1 OFF=12VDC, J1

ON=24VDC. Voltage is Factory set and Re-Adjusting will void Warranty.

3. Output Connections

Connect the load to the DC (+) and DC (-) terminals observing polarity.

4. Alarm/Trouble Output

a.) AC Fail: Connect the “AC Fail” output “Form C” dry contacts to the monitoring device. In case of AC loss the

relay, which is Fail Safe, will de-energize within one (1) minute.

b.) Battery Fail: Connect the Battery Fail output “Form C” dry contacts to the monitoring device. If a Battery is not

connected or improperly connected, the Yellow LED (L3) will turn ON within one (1) minute and the Battery Fail

output relay, which is Fail Safe, will de-energize.

5. Power Up

When all wiring is complete and checked, switch ON the AC Power. The Green Led (L1) will come ON indicating AC

presence and the AC relay will be energized. Connect Battery observing the correct polarity. For 24VDC use the battery

link provided to connect the two (2) 12 Volt Batteries in series. Secure the enclosure with the 4 screws and with the Key

Lock provided.

NOTE: For UL603 or UL294 applications use a Tamper Switch (Catalog number HPVM3 available separately),

and included enclosure key lock. Connect the tamper switch NC outputs to monitoring device to notify of

enclosure tampering.

4 Maintenance

This unit should be tested at least once a year to verify correct operation in accordance with the following

recommendations;

• Output Voltage Test

Voltage output should be tested under normal load conditions to verify correct levels.

• Battery Test

Battery should be checked for full charge under normal load conditions. This check should verify correct voltage at

both battery terminals and also at the Battery output point on the board to ensure the integrity of all connecting

wiring.

Note: It is recommended to replace the battery at least every 4 years.

WARNING: To reduce risk of electric shock, do not expose unit to rain or excess moisture, and disconnect

power before servicing unit.

For continuous protection against hazard, replace fuses only with exact type and rating. A readily accessible

switched circuit breaker must be available to disconnect main power as required. All power limited wiring should

be routed so that it cannot touch non-power limited wiring; minimum spacing 1/4”. Installation and servicing

should only be made by qualified personnel; contains no user-serviceable parts. Install in accordance with all local

regulations and the National Electrical Code.

Continued on next page...

HP300ULX Installation Document P/N 52386:A 12/29/05 3

5 LED Indications

6 Battery Stand-By Mode Specification Chart

LED Number Power Board (staus when lit)

L1 Green LED - AC present

L2 Red LED - PTC activated

L3 Yellow LED - Battery low or disconnected

L4 Red LED - DC power failure

L5 Red LED - DC output present

Output Battery

Capacity STBY/ALRM 4Hr Stand-By

15Mins/ALRM

24Hr Stand-By

15Mins/ALRM

60Hr Stand-By

5Mins/ALRM

12Ah-12V

STBY 2.00A N/A N/A

ALRM 2.00A N/A N/A

17Ah-12V

STBY 2.00A 200mA N/A

ALRM 2.00A 2.00A N/A

55Ah-12V

STBY 2.00A 1.50A 300mA

ALRM 2.00A 2.00A 2.00A

12Ah-24V

STBY 2.00A N/A N/A

ALRM 2.00A N/A N/A

17Ah-24V

STBY 2.00A 200mA N/A

ALRM 2.00A 2.00A N/A

55Ah-24V

STBY 2.00A 1.50A 300mA

ALRM 2.00A 2.00A 2.00A

UL Listing UL294

UL603

UL294

UL603

UL1481

Continued on next page...

4HP300ULX Installation Document P/N 52386:A 12/29/05

For additional information:

• Visit our website at http://www.honeywellpower.com

• Contact Technical Support at 1(877) HPP-POWR

• E-mail us at hpp.techserv@honeywell.com

Inhaltsverzeichnis

Andere Honeywell Stromversorgung Handbücher

Honeywell

Honeywell PS1202C Bedienungsanleitung

Honeywell

Honeywell VX89301PWRSPLY Bedienungsanleitung

Honeywell

Honeywell Notifier PSU7A Bedienungsanleitung

Honeywell

Honeywell PS-HL-138 BM Series Bedienungsanleitung

Honeywell

Honeywell Notifier AMPS-24/E Bedienungsanleitung

Honeywell

Honeywell HP600ULM Bedienungsanleitung

Honeywell

Honeywell Notifier ACPS-610/E Bedienungsanleitung

Honeywell

Honeywell Gamewell FCI GFPS-9 Bedienungsanleitung

Honeywell

Honeywell HPF-PS6 Bedienungsanleitung

Honeywell

Honeywell PRO32E1PS Gebrauchsanweisung

Honeywell

Honeywell PS1202A00 Bedienungsanleitung

Honeywell

Honeywell GENT VCS-PSU-N Bedienungsanleitung

Honeywell

Honeywell HPTV2404 Technisches Handbuch

Honeywell

Honeywell HP24100ULWP Bedienungsanleitung

Honeywell

Honeywell 9000311PWRSPLY Bedienungsanleitung

Honeywell

Honeywell NOTIFIER APS2-6R/E Bedienungsanleitung

Honeywell

Honeywell 900P01 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell Fire-Lite FL-PS6 Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT SK-PS6 Bedienungsanleitung

Honeywell

Honeywell HP312CX Bedienungsanleitung

Honeywell

Honeywell 9007AX01 Bedienungsanleitung

Honeywell

Honeywell HPF24S6 Bedienungsanleitung

Honeywell

Honeywell HP400ULACM4CB Bedienungsanleitung

Honeywell

Honeywell NOTIFIER ALI50EN Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung