Honeywell PS-HL-138 BM Series Bedienungsanleitung

PAK200467-HW_01A March 2020 2020 Honeywell Security

PS-HL-138xxBM Series : 13.8V dc Switch Mode Power Supplies

with Standby battery charging, fault monitoring & remote fault signalling

PS-HL-13805BM-4OP (5A / 4 x Fused Outputs) PS-HL-13810BM-8OP (10A / 8 x Fused Outputs)

FEATURES

High efficiency cost effective power supply range ideal for Access Control applications.

Featuring a regulated 13.8V dc output supplying continuous full rated current to load

and a universal mains voltage input. Standby battery recharging is achieved within 24h

for an 18Ah battery. Maximum battery life is assured using deep discharge protection

to prevent premature battery failure when operating in standby mode for extended

periods. Two sets of volt free contacts are provided to signal (i) loss of mains and (ii)

battery and loss of output faults. The 5A model is provided with 4 x 1.25A Fused

Outputs whilst the 10A model is provided with 8 x 1.25A Fused Outputs.

•Continuous full rated current to load

•18Ah Standby battery recharged to 80% within 24 hours

•Universal mains input voltage 90-264V ac

•High efficiency electronics for reduced running costs and lower operating

temperatures

•Installer safe design with all high voltage electronics fully shrouded

•Full electronic short circuit and overload protection on load output under mains

operation

•Mains transient protection circuit

•Lid and removal from wall tamper detection

•Green Mains present LED

•Red Fault LED

•Volt free contact signalling mains failure

•Volt free contact signalling output and battery faults

•Individually Fused Outputs

Honeywell Middle East

Emaar business Park, Tel: +971 4 450 5800

UAE : www.honeywell.com

PAK200467-HW_01A March 2020 2020 Honeywell Security

COMPLIANCE

This power supply unit meets the essential requirements of the following European

Directives:

Low Voltage 2014/35/EU EMC 2014/30/EU WEEE 2012/19/EU RoHS

2011/65/EU

SPECIFICATION

Input Specification

Voltage (rated)

100-240V ac

Voltage (operating)

90-264V ac

Frequency

50-60Hz

Max current

See Model Specification Table overleaf

Mains Input Fuse

See Model Specification Table overleaf

Max standby Power

See Model Specification Table overleaf

Output Specification

Voltage

13.5 –14.2V dc (13.8V dc nominal) on mains power

10.0 –12.3V dc on battery standby

Max load current

See Model Specification Table overleaf

Ripple

150 mV pk-pk max

Load output Fuse

See Model Specification Table overleaf

Overload

Electronic shutdown until overload or short circuit

removed (under mains power only)

Standby Battery

Battery Type

12V Valve Regulated Lead Acid

Battery Capacity

See below under enclosure size.

Battery Charging Fuse

protection

See Model Specification Table overleaf

Mechanical

Model

PS-HL-13805BM-4OP

PS-HL-13810BM-8OP

Enclosure Dimensions

w x h x d (mm) [external]

355 x 330 x 80

390 x 410 x 80

Max Battery Capacity

1 x NP17 (18Ah)

2 x NP17 (18Ah)

Weight (kg) excluding

battery

4.3

5.42

Environmental

Temperature

-10 to +40°C (operating) 95% RH non-condensing

-20 to +80°C (storage)

PAK200467-HW_01A March 2020 2020 Honeywell Security

Model Specification Table

PS-HL-13805BM-4OP

PS-HL-13810BM-8OP

Max Output Current to load

2 x 5A

Output Fuses* (20mm glass)

F5.0A (4 x 1.25A)

2 x F5.0A (8 x 1.25A)

Max Mains Input Current (at

90V ac)

2.0A

3.0A

Mains Input Fuse

(20mm 250Vac HBC)

T3.15A

Battery Fuse Protection

F5.0 A

2 x F5.0A

LOCAL INDICATORS

Local Indicators

MAINS LED (Green)

Mains present

FAULT LED (Red)*

Flashes (1s period) when: loss of mains, battery

disconnected, output fuse fail, battery fuse fail, output

short circuit or low output voltage

*For 10A model, only one Fault LED will be visible via front panel. Each module has

independent fault monitoring and signalling.

PAK200467-HW_01A March 2020 2020 Honeywell Security

CONNECTIONS

+LOAD 1,2,3,4

+ve voltage output to load equipment

-LOAD 1,2,3,4

-ve voltage output to load equipment

EPS Fault

Voltfree contacts for loss of mains indication

GEN Fault

Voltfree contacts for general faults (see signalling outputs)

+BATT

-BATT

+ve (Red lead) connection to standby battery

-ve (Black lead) connection to standby battery

SIGNALLING OUTPUTS

GEN Fault (general)

Open when battery disconnected, *output fuse fail,

battery fuse fail or output short circuit. (*Applies only to

O/P 1 of multiple fused units).

Rating: 0.1A @ 60V dc N/O volt free contact.

EPS Fault (mains)

Open when loss of mains for more than 10s.

Rating: 0.1A @ 60V dc N/O volt free contact.

Lid Tamper

Note: Contact open in when lid opened by normal

means or unit is removed from mounted surface

Rating: 3A @ 125V ac N/O volt free contact.

PAK200467-HW_01A March 2020 2020 Honeywell Security

INSTALLATION &COMMISSIONING

This unit is only suitable for installation as permanently connected equipment. The

PSU is NOT

SUITABLE for external installation. EQUIPMENT MUST BE EARTHED. Before installation,

ensure that external disconnect device is OFF. The PSU should be installed according to

all relevant safety regulations applicable to the application.

Mounting

1) Mount securely in correct orientation allowing minimum clearance –see diagram.

2) Route mains and low voltage output cables via different knockouts and/or cable

entry holes.

3) Use bushes and cable glands rated to UL94 HB minimum.

Mains Power Up

4) Attach correctly rated mains cable (minimum 0.5mm2[3A], 300/500V ac) and

fasten using cable ties.

5) Apply mains power. Check for 13.8V dc on load outputs. Check green Mains LED is

on.

6) Disconnect mains power.

Load Output

7) Attach correctly rated load cable and fasten using cable ties. Note polarity.

8) Apply mains power. Check green Mains LED is on.

9) NOTE: Red LED may be illuminated to indicate that no battery has been

connected. This is normal.

10) Verify load is operating correctly.

11) Disconnect mains power.

Standby Battery

12) Attach supplied battery cables to terminal block and battery.

NOTE: ensure correct polarity of battery connections: +ve use red lead, -ve use

black lead.

PAK200467-HW_01A March 2020 2020 Honeywell Security

13) Apply mains power. Check green Mains LED is on.

14) Check there is no fault indication on Red LED.

15) Disconnect mains power. Check that the batteries continue to supply voltage and

current to the load. The Green LED should be off.

NOTE: Batteries must have sufficient charge to supply the load

16) Reconnect mains power. Green LED should be on.

Tamper

17) Check that the tamper screw makes good contact with the mounting surface.

Check that the tamper switch is:

closed when the lid is closed, and the lid screw is fitted

open when the lid is open.

18) Close cover and secure using fastening screw(s) provided.

OPERATING INSTRUCTIONS

This unit is intended for use by Service Personnel only. There are NO USER

SERVICEABLE parts inside.

The green Mains LED will be illuminated whilst the mains supply is present. In the

event of a fault condition the red Fault LED will flash and the corresponding (EPS or

GEN) fault signal contacts will open.

PREVENTATIVE MAINTENANCE

This unit is intended for use by Service Personnel only. There are NO USER

SERVICEABLE parts inside.

There is no regular maintenance required of the PSU other than periodic testing,

calibration check and replacement of the standby batteries. Reference should be

made to the battery manufacturer's documentation to determine typical/expected

battery life with a view to periodic replacement of the battery.

CAUTION

Dispose of used batteries according to the battery manufacturer’s

instructions and all local and national regulations.

PAK200467-HW_01A March 2020 2020 Honeywell Security

This page has been intentionally left blank.

PAK200467-HW_01A March 2020 2020 Honeywell Security

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Stromversorgung Handbücher

Honeywell

Honeywell Notifier ACPS-610/E Bedienungsanleitung

Honeywell

Honeywell HPTV24-E Series Technisches Handbuch

Honeywell

Honeywell HP300ULX Technisches Handbuch

Honeywell

Honeywell HPTV2416UL Technisches Handbuch

Honeywell

Honeywell HP400ULACM4CB Bedienungsanleitung

Honeywell

Honeywell 900P01 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell HPTV2404 Technisches Handbuch

Honeywell

Honeywell HPTV2408UL Technisches Handbuch

Honeywell

Honeywell HP312CX Bedienungsanleitung

Honeywell

Honeywell Gamewell FCI GFPS-9 Bedienungsanleitung

Honeywell

Honeywell HPF24S8 Technisches Handbuch

Honeywell

Honeywell Notifier PSU7A Bedienungsanleitung

Honeywell

Honeywell HP300ULM Technisches Handbuch

Honeywell

Honeywell VX89301PWRSPLY Bedienungsanleitung

Honeywell

Honeywell 208414 Bedienungsanleitung

Honeywell

Honeywell HPF24S6 Bedienungsanleitung

Honeywell

Honeywell HPF-PS6 Bedienungsanleitung

Honeywell

Honeywell PEHA D 942 SPV Bedienungsanleitung

Honeywell

Honeywell PS1202A Bedienungsanleitung

Honeywell

Honeywell TC-RPCXX1 Bedienungsanleitung

Honeywell

Honeywell PRO32E1PS Gebrauchsanweisung

Honeywell

Honeywell Galaxy Power RIO Benutzerhandbuch

Honeywell

Honeywell HPR2416CBUL Bedienungsanleitung

Honeywell

Honeywell DCPSU-24 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung