Honeywell 5878 Bedienungsanleitung

K14395 6/06 Rev. A

5878

Wireless Wall Transmitter

USER GUIDE

GENERAL INFORMATION

The 5878 is a compact, 6-button wall-mounted

wireless transmitter that permits an alarm system

or home automation devices to be controlled

remotely. The transmitter is typically used for

security system arming and panic and controlling

output relay operations associated with home

automation devices. Check with your installer for

operation of the buttons on your unit.

OPERATING THE BUTTONS

To activate a programmed function, press and hold

the associated button(s) down. The LED will flash

green to indicate the unit has transmitted in

Standard mode, or red to indicate it has transmitted

in High-Security mode.

In order to minimize the possibility of

accidental transmissions, the buttons on

the 5878 must be pressed and held for at

least 1/2 second to activate the

transmitter.

5878-004-V0

LED

STAY

AWAY

Figure 1 - 5878 Transmitter

Table 1 - Transmitter Functions

(Complete this table with your installer)

Button Function

LOW BATTERY INDICATION

When a Button is pressed and a Low Battery

condition exists, a message is transmitted to the

control panel and LOW BAT will be displayed on

the keypad. The LED will not flash during

transmission if the battery is low.

Replacing the Battery

1. Slide out the battery tray located at the bottom

of the 5878.

2. Carefully remove the battery.

3. Press and hold any button for at least one

second.

4. Insert a new battery in case back location as

shown in Figure 2. Positive (+) end must face

up. Use Maxell CR2032, Duracell DL 20325, or

Varta CR2032 lithium battery only.

5. Slide the battery back into the 5878.

6. Press any button and verify that the LED

flashes.

Improper installation will result in

damage to the transmitter.

BATTERY

AWAY STAY

NOTE

POSITIVE (+) SIDE

MUST FACE UP

5878-002-V0

Figure 2 - Replacing the Battery

LIMITATIONS STATEMENT

Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach the alarm receiver.

Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object somehow

blocks the signal path.

Wireless button type transmitters that have visual and audible indications of status must be used to confirm that the

desired action (such as arming) has occurred after pressing a function button on any of these transmitters. Be sure to

listen for appropriate audible and visual indications that such action has occurred. Otherwise, you could inadvertently

leave yourself or your premises unprotected.

External factors such as humidity, high or low temperatures, or constant activation of a programmed button may

reduce battery life in a given installation. If the button unit is used infrequently, activate it regularly (once per week)

to confirm operation. A button type transmitter will report a low battery condition to the alarm control when a low

battery status is detected.

FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM,

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH WHICH THIS DEVICE IS USED.

FCC AND INDUSTRY CANADA STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS210 OF INDUSTRY CANADA. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS

DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

THE USER SHALL NOT MAKE ANY CHANGES OR MODIFICATIONS TO THE EQUIPMENT UNLESS AUTHORIZED BY THE

INSTALLATION AND SETUP GUIDE OR THE USER GUIDE.

12800 Brookprinter Place,Poway, CA 92064

www.honeywell.com/security

‡K14395TŠ

‡K14395TŠ‡K14395TŠ

‡K14395TŠ

K14395 6/06 Rev. A

Andere Honeywell Fernbedienung Handbücher

Honeywell

Honeywell TrueIAQ Bedienungsanleitung

Honeywell

Honeywell 40015 Bedienungsanleitung

Honeywell

Honeywell Versa-Pro UDC3000 Bedienungsanleitung

Honeywell

Honeywell REDLINK ERM5220R Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5804BD Bedienungsanleitung

Honeywell

Honeywell DF-RC Bedienungsanleitung

Honeywell

Honeywell Hometronic HRD 20 Bedienungsanleitung

Honeywell

Honeywell TCC800M Bedienungsanleitung

Honeywell

Honeywell FocusPRO 6000 Series Bedienungsanleitung

Honeywell

Honeywell TS607 Bedienungsanleitung

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Bedienungsanleitung

Honeywell

Honeywell REM5000R01 Bedienungsanleitung

Honeywell

Honeywell 5805-6A Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5804BDV Bedienungsanleitung

Honeywell

Honeywell TCC800MS Bedienungsanleitung

Honeywell

Honeywell HCW 23 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5804BDV-CN Bedienungsanleitung

Honeywell

Honeywell Wireless Remote Control Bedienungsanleitung

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell Power Presenter RF Bedienungsanleitung

Honeywell

Honeywell HS3FOB1S Bedienungsanleitung

Honeywell

Honeywell NOTIFIER LCD6000A Bedienungsanleitung

Honeywell

Honeywell 42136 Bedienungsanleitung

Honeywell

Honeywell YTH5320R Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung