Honeywell DF-RC Bedienungsanleitung

DF-RC

Honeywell

Manual

RF Remote Control Decorative Fire

Key Up

Key Down

Key Stop/Stand-by

Key Menu

Display

DISPLAY AND KEYS

Display

Manual operation.

Time schedule active.

Active time period.

Closed (left) or open ﬁre place type (right).

Decorative ﬁre is on.

Decorative ﬁre can be ignited.

Fault of decorative ﬁre can be reset.

Burner off/setting down (left), burner on/setting up (right).

Busy (for instance while decorative ﬁre is been ignited).

Fault.

Main plug of the decorative ﬁre is plugged in the other way round.

RF-communication.

Batteries are almost empty (symbol ﬂashes).

Time representation (24-hours or 12-hours).

Days of the week. Square indicates actual day.

Temperature representation.

Temperature sensor(s) are defect.

Keys

Enhance setting or change selection.

Lower setting or change selection.

Choose menu and menu selection.

Stop setting menu or go to stand-by.

SET UP FOR OPERATION

The RF remote control makes it possible to operate your decorative ﬁre

both manual as by means of a time schedule.*

The temperature and the ﬂame height can be manually controlled. The

time schedule only controls the temperature.

The possible time schedules are*:

A time schedule with the same settings for each day.

A time schedule with separate settings for the week days (monday to

friday) and the weekend.

A time schedule with separate settings for each day.

For each day, two, four or six different time periods can be set.*

The time schedule can easily be set by setting the begin time and the

temperature set point of each period.

Flame Symbol

A ﬂame symbol indicates that the burner of your decorative ﬁre has been

switched on.

Batteries

Before you can take the RF remote control in operation, the two supplied

batteries (type AA) have to be placed. After the batteries have been

placed, the RF remote control is ready for manual operation with ﬂame

height control. To save batterie life, some time after the last key pressure,

the display goes blanc*, unless the decorative ﬁre is switched on.

* The availability of the option depends on the factory setting of the

decorative ﬁre.

•

Binding RF Remote Control

The RF remote control can only communicate with a decorative ﬁre after

the RF remote control has been bound with that decorative ﬁre.

If both devices are switched on within 5 minutes after each other, the

binding goes automatically.

This display is shown if the RF remote control has

not been bound. The symbol ﬂashes. Make

sure the decorative ﬁre has not been switched on

for more than 5 minutes and start the binding as

follows:

Press keys and simultaneously.

The display below is shown.

This display is shown during binding. The symbol

ﬂashes. When the binding is ﬁnished, the default

display is shown.

Note: In case of replacement of the decorative ﬁre or the RF remote

control, the binding has to be initiated manual, see Binding RF

remote control, on page17.

Time and Day

The time schedule of the RF remote control can only be used if the

time has been set. The time and day can be set in the User Menu, see

Setting Time and Day on page 13. The time representation, 12-hours or

24-hours, can be set in the Installation Menu, see Choice 12- or 24-

Hours Representation on page 15.

OPERATION

The RF remote control is equipped with a display and four keys. Because

of this the decorative ﬁre can be easily operated and settings easily be

adjusted.

There are two setting menus available:

User menu

Installation menu

Press key once to select the User menu, or keep key pressed for

ten seconds to select the Installation menu.

Manual Operation

Dependent on the choice made in the User menu, the temperature or the

ﬂame height can be controlled manual.

Flame height control

The decorative ﬁre must be manually switched on and off.

Igniting decorative ﬁre

Press keys and simultaneously if the

adjacent display is shown.

•

This display is shown. The symbols and

are ﬂashing to indicate the decorative ﬁre is being

ignited.

After the decorative ﬁre has been ignited, the

display below is shown.

The ﬂame height can now be manually controlled.

Setting ﬂame height

Press key or once. The display below is shown.

The value of the current ﬂame height ﬂashes.

Set the required ﬂame height by pressing key

or . Dependent on the key pressed, the symbol

or is shortly visible on the display. The ﬂame

height can be set between1 and 15.

Wait a few seconds or press key to leave the menu.

Note: The ﬂame height can only be controlled if the decorative ﬁre has

been switched on.

Switching off the decorative ﬁre

Press key once to switch off the decorative ﬁre.

This display is shown. The symbol ﬂashes to

indicate the decorative ﬁre is being switched off.

After the decorative ﬁre has been switched off, the

default display is shown again.

Temperature control

The decorative ﬁre is automatically switched on and off according to

the heat demand. Press key or once to adjust the required

temperature. The display below is shown.

The current temperature set point ﬂashes. Set

the required set point by pressing key or .

Dependent on the key pressed, the symbol or

is shortly shown on the display. The temperature

can be set between 7,0 and 35,0 °C.

Wait a few seconds or press key to leave the menu.

Temporarily interrupting temperature control

When temperature control is used, the decorative ﬁre can temporarily be

switched off.

Press key once to switch off the decorative ﬁre.

This diplay is shown. The symbol ﬂashes to

indicate the decorative ﬁre is being switched off.

After the decorative ﬁre has been switched off, the

display below is shown.

The symbol ﬂashes to indicate the

decorative ﬁre has to be ignited manually by

pressing the keys and simultaneously.

When the decorative ﬁre is ignited again, the

temperature control becomes active.

Note: The temperature set point can not be changed during the

temporarily temperature control interruption.

Time Schedule

The temperature is controlled according to the time schedule, see Setting

Time Schedule on page 14. The decorative ﬁre is fully automatically

ignited and switched off.

Temporarily changing the temperature set point

The temperature set point of a time schedule period can temporarily be

enhanced or lowered. Press key or once to set the temporarily set

point. The display below is shown.

The current temperature set point ﬂashes. Set

the temporarily required temperature set point

by pressing key or . Dependent on the key

pressed, the symbol or is shortly shown on

the display.

Wait a few seconds or press key to leave the menu.

This display (example) is shown. The symbol

indicates that the temperature set point has been

adjusted manually.

The temporarily adjustment can be undone by setting the manually

adjusted set point back to the set point of the current time period. In

case of a transition to a new time period, the temporarily adjustment is

cancelled automatically.

Inhaltsverzeichnis

Andere Honeywell Fernbedienung Handbücher

Honeywell

Honeywell ADEMCO 5804BDV Bedienungsanleitung

Honeywell

Honeywell NOTIFIER LCD6000A Bedienungsanleitung

Honeywell

Honeywell Power Presenter RF Bedienungsanleitung

Honeywell

Honeywell Wireless Remote Control Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5804BDV Bedienungsanleitung

Honeywell

Honeywell 42136 Bedienungsanleitung

Honeywell

Honeywell Hometronic HRD 20 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5804BD Bedienungsanleitung

Honeywell

Honeywell YTH5320R Bedienungsanleitung

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Bedienungsanleitung

Honeywell

Honeywell 5834-4 Betriebsanleitung

Honeywell

Honeywell HS3FOB1S Bedienungsanleitung

Honeywell

Honeywell REDLINK ERM5220R Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT RA-2000 Bedienungsanleitung

Honeywell

Honeywell FocusPRO 6000 Series Bedienungsanleitung

Honeywell

Honeywell 40015 Bedienungsanleitung

Honeywell

Honeywell TS607 Bedienungsanleitung

Honeywell

Honeywell Silent Knight 6860 Technisches Handbuch

Honeywell

Honeywell TrueIAQ Bedienungsanleitung

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Bedienungsanleitung

Honeywell

Honeywell HCW 23 Bedienungsanleitung

Honeywell

Honeywell TCC800M Bedienungsanleitung

Honeywell

Honeywell Lyric RF6FOB Bedienungsanleitung

Honeywell

Honeywell REM5000R01 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung