Honeywell Voyager XP 1472g Series Bedienungsanleitung

Voyager™ XP 1472g Series

Cordless Area-Imaging Scanner

Quick Start Guide

VG1472-EN-QS-01 Rev A

6/19

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Honeywell Voyager XP 1472G o

cerca il tuo prodotto tra le migliori offerte di Palmari e Barcode Scanner

Note: Refer to your user’s guide for information about cleaning

your device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off the computer’s power before connecting the base, then

power up the computer once the base is fully connected. When

the base is connected and powered up, put the scanner in the

base to establish a link. The green LED on the base flashes to

indicate the scanner’s battery is charging.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

USB Connection:

Keyboard Wedge Connection:

RS232 Serial Port Connection:

RS485 Connection:

Reading Techniques

The view finder projects an aim-

ing dot that should be centered

over the bar code, but it can be

positioned in any direction for a

good read.

Hold the scanner over the bar

code, pull the trigger, and center

the aiming dot on the bar code.

The aiming dot is smaller when

the scanner is closer to the code

and larger when it is farther from the code. Hold the scanner

close to smaller bar codes, and farther away from large bar

codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need

to tilt the scanner at an angle so the bar code can be scanned.

Note: If the scanner razzes when scanning a bar code, the link

has not been established. If the scanner beeps once, the

link has been established.

Standard Product Defaults

The following bar code resets all standard product default set-

tings.

Note: PDF and 2D bar codes can only be read by Voyager model

1472g2D and cannot be read by model 1472g1D.

Standard Product

RS485 Interface

The RS485 interface defaults to port 5B. If you have an IBM POS

terminal using port 9B, scan the appropriate code below to pro-

gram the terminal, then power cycle the cash register.

Note: For additional RS485 interface selections, see the User’s

Guide for your product.

USB Serial

Scan the following code to program the scanner to emulate a

regular RS232-based COM Port. If you are using a Microsoft®

Windows® PC, you will need to download a driver from the Hon-

eywell website (www.honeywellaidc.com). The driver will use the

next available COM Port number. Apple® Macintosh computers

recognize the scanner as a USB CDC class device and automati-

cally use a class driver.

Note: No extra configuration (e.g., baud rate) is necessary.

IBM Port 9B HHBCR-1

Interface

IBM Port 9B HHBCR-2

Interface

USB Serial

USB PC Keyboard

Scan the following code to program the scanner for a USB PC

Keyboard.

Keyboard Country

Scan the appropriate country code that follows to program the

keyboard layout for your country or language. By default,

national character replacements are used for the following

characters: #$@[\]^‘{|}~ Refer to the ISO 646 Character

Replacements chart in your User Guide to view the character

replacements for each country.

USB PC Keyboard

USA (Default)

Belgium

Denmark

Finland

France

Note: For a complete list of country codes, see the User’s Guide

for your product.

Germany/Austria

Great Britain

Italy

Norway

Spain

Switzerland

Locked Link

If you link a scanner to a base using the Locked Link Mode,

other scanners are blocked from being linked if they are inad-

vertently placed into the base. If you do place a different scan-

ner into the base, it will charge the scanner, but the scanner will

not be linked.

To use a different scanner, you need to unlink the original scan-

ner by scanning the Unlink Scanner bar code.

Override Locked Scanner

If you need to replace a broken or lost scanner that is linked to a

base, scan the Override Locked Scanner bar code with a new

scanner, and place that scanner in the base. The locked link will

be overridden; the broken or lost scanner’s link with the base will

be removed, and the new scanner will be linked.

Unlinking the Scanner

If the base has a scanner linked to it, that scanner must be

unlinked before a new scanner can be linked. Once the previous

scanner is unlinked, it will no longer communicate with the

base. Scan the Unlink Scanner bar code to unlink a scanner.

Locked Link Mode

(Single Scanner)

Override Locked Scanner

Unlink Scanner

Trigger

The following bar codes will allow you to use the scanner in

Manual Trigger - Normal Mode (need to press the trigger to

read) or Presentation mode (the scanner is activated when it

“sees” a bar code).

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add

Tab Suffix bar code. Otherwise, scan the Remove Suffix bar

code to remove the suffixes.

Manual Trigger - Normal

(Default)

Presentation Mode

Add CR Suffix

Add Tab Suffix

Remove Suffix

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Scanner Handbücher

Honeywell

Honeywell A700 Bedienungsanleitung

Honeywell

Honeywell Vuquest 3330g Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell Granit 1280i Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell 4800dr - Document Camera Bedienungsanleitung

Honeywell

Honeywell 4850DR Bedienungsanleitung

Honeywell

Honeywell Vuquest 3320g Bedienungsanleitung

Honeywell

Honeywell Voyager XP 1470g Series Bedienungsanleitung

Honeywell

Honeywell Voyager XP 1470g Series Bedienungsanleitung

Honeywell

Honeywell Xenon XP 1950g Bedienungsanleitung

Honeywell

Honeywell Voyager 1452g Series Bedienungsanleitung

Honeywell

Honeywell QuantumT MS3580 Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell HH480 Bedienungsanleitung

Honeywell

Honeywell Voyager 1400g Series Bedienungsanleitung

Honeywell

Honeywell OrbitCG MS7180 Bedienungsanleitung

Honeywell

Honeywell 3900 Bedienungsanleitung

Honeywell

Honeywell Xenon Series Bedienungsanleitung

Honeywell

Honeywell QuantumT 3580 Bedienungsanleitung

Honeywell

Honeywell Xenon 1932 Bedienungsanleitung

Honeywell

Honeywell YOUJIE YJ-HH360 Bedienungsanleitung

Honeywell

Honeywell Voyager 147 Series Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung