Honeywell LYNXR-I Series Betriebsanleitung

K14945 1/08 Rev. A

LYNXR

LYNXRLYNXR

LYNXR-

-I Series

I SeriesI Series

I Series

Security Systems

Security SystemsSecurity Systems

Security Systems

New Features and Additional Programming Changes

The LYNXR-I Series Security System includes several new features that must be programmed in accordance

with this supplement. These features and programming steps are not included in the Installation and Setup

Guide or the Programming Guide that are provided with this control.

Please follow the new and revised diagrams and procedures contained in this supplement when installing

and programming the new features.

The new LYNXR-I Series features include:

•Compatibility with the AlarmNet GSML/GSMVL Communications Devices

•New 24-hour Carbon Monoxide Monitor Zone Type 14 and compatibility with the 5800CO Carbon

Monoxide Sensor.

•Remote Services (requires compatible AlarmNet Communications device)

Wiring Overview

The following diagram provides an overview of the LYNXR-I Series control’s wiring connections. A summary

of connections diagram is also provided.

09012-009-V0

SUPER HIGH-CAPACITY

BATTERY CONNECTOR

TERMINAL

STRIP

TELEPHONE

CONNECTIONS

LRR/IP

COMMUNICATIONS

PORT

GSML/GSMVL

COMMUNICATIONS

PORT

LOCAL

SOUNDER

DISABLE

STANDARD

HIGH-CAPACITY

BATTERY CONNECTOR

LYNXR-I Series Wiring Connections

- 2 -

Installing the AlarmNet GSML/GSMVL Communications Device

1. Install the module into the control back plate and secure it with the three provided screws.

2. Insert the antenna into the retaining slots in the control back plate.

3. Use double-stick tape to secure antenna to the control back plate.

4. Connect the provided communications cable between the GSML/GSMVL module and the control’s PC

board. This cable provides DC power and ground for the module and data in/data out connections.

5. If using the GSMVL, connect the provided shielded audio cable between the GSMVL module and the

control’s PC board.

COMMUNICATIONS

CABLE

GSMVL

ANTENNA

09012-017-V0

SCREW (3)

AUDIO CABLE

(GSMVL ONLY)

Installing the GSML/GSMVL Communications Module

GSML/GSMVL Programming

If you are installing a GSML/GSMVL Communications Device, it must be programmed in the control via the

following new and revised Data Fields.

*55 Reporting Channels

*77 Dynamic Signaling Delay/Dynamic Signaling Priority

*78 Programmable Tone Generation Time

- 3 -

Field ✻55

The allowable combinations of communication reporting channels and reporting options are shown in the

table below. The available options, which depend upon whether AAV is enabled in field *91, are programmed

in field *55. Program the preferred reporting channel in field *77.

If the GSM/IP (Digital Communication with AAV) feature is used (options 5 and 7 in *55), there may be restrictions when

dialing the numbers entered in *41, *42 and *46 (i.e.; #, ✻, pause may not be allowed, or phone number extensions may

not be dialed, etc) depending on the service provider.

Reporting Option

AAV

Enabled? *55 Communication Reporting Channel

Primary Phone only Y/N 0 = Telco Line only (no radio) (see Note 1)

Redundant reports to both channels Y/N 1 = LRR/IP (Digital Communication only) and Telco Line (see Note 1)

Primary Phone is the preferred channel Y/N 1 = LRR/IP (Digital Communication only) and Telco Line (see Note 1)

Y 7 = LRR/IP (Digital Communication w/AAV) and Telco Line (see Notes 2 & 3)

LRR/IP is the preferred channel Y/N 1 = LRR/IP (Digital Communication only) and Telco Line (see Note 1)

LRR/IP Only N 3 = LRR/IP (Digital Communication only) (no Telco Line) (see Notes 4 & 5)

Y 5 = LRR/IP (Digital Communication w/AAV) (no Telco Line) (see Notes 4, 5, 6)

NOTES

1. AAV mode can be established only on Telco Line.

2. AAV mode can be established either on Telco Line or LRR/IP (Digital Communication with Voice Capabilities)

3. Primary phone number programmed in *41 is shared between Telco Line and LRR/IP (Digital Communication with Voice Capabilities)

4. Follow Me System, Follow Me Reminder and Pager features are not supported. These features will not work if selected in *49.

5. Speaker Phone and Remote Phone Access are not available. These features should be disabled in *47 and *91. Download over the

Phone Line feature is also unavailable.

6. AAV mode can be established only on LRR/IP (Digital Communication with AAV Capabilities)

7. If AAV is selected and LRR/IP communications device is enabled, you must enter “0” (primary dialer preferred channel) as the second

entry in Field *77.

8. The PABX phone number entered in field ✻40 is not dialed on GSM/IP (Digital Communication with AAV). However, it is used for dialing

on the Telco Line.

Legend

LRR/IP (Digital Communication only) = Digital GSM Communication Channel

LRR/IP (Digital Communication with AAV) = GSM Communication Channel with voice capabilities (a radio with voice

capability is required to use AAV options)

Telco Line = Land Phone Line

✻55 Reporting Channels

0 = Telco Line (no Radio)

1 = LRR/IP(Digital Communication only) and

Telco Line

3 = LRR/IP (Digital Communication only) (no

Telco Line)

5 = LRR/IP (Digital Communication with AAV)

(no Telco Line)

7 = LRR/IP (Digital Communication with AAV)

and Telco Line

This option is used to enable/disable Central Station

reporting via the LRR/IP Communications Device (See

Field *77). Upload/ download via the Internet IP module

is not affected by this entry.

The option specifies the channel that the control will use

when sending reports to the Central Station (Follow Me

phone, and Pager). Select some or all channels as required.

IMPORTANT NOTE

Make sure that selected channels are physically available and

functional.

Note: Zone 103 can not be bypassed.

- 4 -

✻77 Dynamic Signaling Delay/Dynamic

Signaling Priority

1st Entry (delay before switching Central Station

reporting path)

0 = Redundant reporting

on dialer and LRR/IP

communications

device

7 = 105 seconds

8 = 120 seconds

9 = 135 seconds

#10 = 150 seconds

1 = 15 seconds #11 = 165 seconds

2 = 30 seconds #12 = 180 seconds

3 = 45 seconds #13 = 195 seconds

4 = 60 seconds #14 = 210 seconds

5 = 75 seconds #15 = 225 seconds

6 = 90 seconds

2nd Entry

0 = Primary Dialer Preferred Channel

1 = LRR/IP Preferred Channel

2 = LRR/IP reporting only

Intended for use with LRR/IP communication device

reporting. This field’s 1st Entry allows you select the time-

out period the panel will wait for acknowledgment from

the first reporting destination (preferred channel) before it

attempts to send a message to the second destination. This

delay is per message. The 2nd entry allows you to select

the (Dynamic Signaling Priority) preferred reporting

channel.

Notes: (1) You must also enable/disable LRR/IP Device in field *55.

(2) If Remote Phone Access is enabled, and Primary Phone

is used as a Preferred Channel, Dynamic Signaling

Delay should be at least 30 sec in order to prevent

duplicate reports.

(3) For UL installations Dynamic Signaling Delay cannot

exceed 15 sec. If Primary Phone is used as a Preferred

Channel, duplicate reports may sent.

1st Entry

Enables Dynamic Signaling Delay. The entry of digits 1-9

or #10-#15. Delays can be selected from 0 to 225 seconds,

in 15-second increments. If 0 is entered, the control panel

will send redundant reports to both Primary Dialer and

the LRR/IP communications device.

2nd Entry

The second entry determines the alternate Central Station

communication path that will be initiated after the time-

out period.

✻78 Programmable Tone Generation Time

00 = Disabled

01-09 = 100-900 ms

10-99 = 1.0 – 9.9 secs.

This field is used to set the time delay between when a

connection is established on a Radio (digital

communication with voice capabilities) session to when the

2100 Hz “training”tone is terminated. Enter any digit

between 00 and 99.

Note: This field only applies when a GSMVL radio is installed in the

control. Otherwise, enter “00” to disable.

Installing a 5800CO Carbon Monoxide Sensor

Zone type 14 can be assigned to any wireless zone with a carbon monoxide detector. If you are installing a

5800CO Carbon Monoxide Sensor, program it in Field *56 (Enhanced Zone Programming Mode) as ZT14 (24-

hour Carbon Monoxide Monitor), Input Type 3 (Supervised RF) and Loop 1. This zone type is always active

and cannot be bypassed. ZT14 is also available in Field *80 Device Programming Menu Mode.

When a Carbon Monoxide alarm is detected, Zone Type 14 causes the sounder output to pulse. The Temporal

pulse sounding for a CO alarm consists of the following: 4 pulses –pause –4 pulses –pause –4 pulses –

pause. . .. Additionally, the system will announce “Carbon Monoxide Alarm”or “Carbon Monoxide Fault”

and the associated zone number. Additionally, the Contact ID®Reporting Code 162 (Alarm, Carbon

Monoxide Detector) will be sent to the Central Station.

- 5 -

Remote Services

Honeywell now offers a new series of web based services that provides consumers with the ability to

communicate with their security system remotely via three new features. In order to use these services, a

compatible AlarmNet Communications device must be installed.

Remote Access feature - Allows users to access their security system from a computer via a website.

Multi-Mode (E-mail Notification) feature –Provides users with notifications of system events via e-mail and

text message.

SMS feature –Allows users to perform system functions and receive confirmations via text messages.

Dealers will initially enroll their customers for web services during account programming through the

AlarmNet Direct website. https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx

The features that can be enabled include Remote Access and Multi-Mode. Once enabled, the specific

programming fields associated with these features can be programmed either remotely using the AlarmNet

Direct website or locally using the 7720P local keypad programming tool. Additionally, if you are enabling

the Multi-mode feature, it must be programmed in the LYNXR-I Series control.

LRemote Access and Multi-Mode have not been evaluated by UL.

Remote Access Feature

Remote Access enables the user to remotely control the security system using a standard web browser.

To Enable Remote Access:

•Remote Access must be enabled as part of Communications Device Programming on the AlarmNet

Direct website.

•A keypad address of "1" must be enabled in the communication device in order for the device to talk to

the control panel.

To Select the User Interface:

Select “LYNX Keypad”as the User Interface during account programming on the AlarmNet Direct website.

Multi-mode Feature

Multi-mode enables users to receive e-mail notification of system events. Since the communication device is

emulating a 4204 or two 4204 modules, there is no additional hardware to install.

E-mail notification is intended as a convenience for the user, and does not replace Central Station reporting of critical

events (alarms, troubles, etc.).

Configuring Multi-Mode

The communication device emulates one or two standard 4204 relay modules for purposes of triggering

events for sending e-mail reports. If "4204 Sourced" is selected as part of Communications Device

Programming, you must enable Multi-Mode Address 6 or 7 in Programming Field *86 in the Control Panel.

If "2-4204 Sourced" is selected as part of Communications Device Programming, you must enable both.

When "4204 Sourced" is selected, the user can be notified of up to four events, and when "2-4204 Sourced" is

selected, the user can be notified of up to eight system events. The Multi-Mode Address on the website must

match the address of the Multi-mode (e-mail notification) address(es) enabled in the LYNXR-I Series control

panel in Field *86.

Events used to send e-mail messages are defined on the Honeywell Total Connect website, and must

correspond to (e-mail) event triggers programmed in the control panel as events 09-16 in field *80 Device

Programming Menu Mode.

Programming Multi-mode (E-mail) Event Triggers

The following new programming field has been added to support the Multi-mode features.

- 6 -

✻86 Multi-mode (E-mail notification)

Address(es)

0 = Disable multi-mode devices

1 = Enable multi-mode device address #6 only

2 = Enable multi-mode device address #7 only

3 = Enable multi-mode addresses #6 & #7

Enable if using AlarmNet Remote Services e-mail

notification (multi-mode) feature. The address(es) used

must also be enabled in the AlarmNet communication

device. For more information refer to the instructions

provided with the Communications Device being installed.

Field * 80, which is normally used to program X10 Powerline Carrier Devices, is now also used to program

Multi-mode (e-mail) Event Triggers. Up to eight events can be programmed; these are assigned as Device

Numbers 09-16 in *80.

Programming Default Tables

In addition to adding new defaults associated with these new features, the start/end defaults for Daylight

Savings time have been revised. The revised defaults are as follows:

Function Table 1 Table 2 Table 3 Table 4

*29 Daylight saving time start/end month 3,11 3,11 3,11 3,11

*30 Daylight saving time start/end weekend 2,1 2,1 2,1 2,1

*55 Reporting Channels 0 0 0 0

*78 Programmable Tone Generation Time 0,0 0,0 0,0 0,0

*86 Multi-mode (E-mail notification) 0 0 0 0

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 1 and 2 (devices 01-07 and 09-15 have no default values)

Start Stop

Device Number

Action

Event

Zone List

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

16 2 33 36

✻80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 4 (devices 02-07 and 10-15 have no default values)

Start Stop

Device Number

Action

Event

Zone List

Zone Type

System Operation

Restore of

Zone List

Zone type

System operation

09 2 2 1 2

16 2 33 36

For ZT42 (Low Batt) use only as a start, with a stop of ZT22 (disarm). If ZT42 is used for

both start and stop it will not trigger.

- 7 -

WEEKLY TESTING IS

REQUIRED TO ENSURE

PROPER OPERATION

OF THIS SYSTEM

POWER SHUTDOWN NOTE: AT 6.0VDC THE SYSTEM WILL NOT OPERATE.

PREMISES

TELEPHONE

SOUNDERS PLCD AC

K10145X10 PLUG-IN

TRANSFORMER

9VAC, 25VA

EARTH

GROUND

INCOMING

TELEPHONE

LINE

TO 24HR 110VAC

UNSWITCHED

OUTLET

TO 24HR 110VAC

UNSWITCHED

OUTLET

PIEZO

6-14VDC

120mA max.

(e.g. WAVE2EX)

6-14VDC

30mA max.

SYNC

COM

DATA

BELL

07000-016-V2

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

THIS EQUIPMENT SHOULD BE INSTALLED IN

ACCORDANCE WITH THE NATIONAL FIRE PROTECTION

ASSOCIATION STANDARDS ANSI/NFPA 70 NATONAL

ELECTRIC CODE AND NFPA 72 NATIONAL FIRE ALARM

CODE, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOC.,

BATTERYMARCH PARK, QUINCY, MA 02269). PRINTED

INFORMATION DESCRIBING PROPER INSTALLATION,

EVACUATION PLANNING AND REPAIR SERVICE IS TO BE

PROVIDED WITH THIS EQUIPMENT.

X10 ONLY

CONNECTIONS

FCC ID: CFS8DLLYNXREN-6

(LYNXR-I) COMPLIES WITH

FCC RULES, PART 68 FCC

REGISTRATION

No. 5GBUSA-25623-AL-E

RINGER EQUIVALENCE: 0.6B

NOTE

USE ONLY THE K10145X10

OR K10145CN CLASS 2

TRANSFORMERS

PROVIDED

LYNXR-I SUMMARY OF CONNECTIONS

LYNXR-I ALSO COMPLIES WITH THE FOLLOWING:

CANADIAN STANDARDS ASSOCIATION (CSA)

C22.1, CANADIAN ELECTRICAL CODE, PART 1,

SAFETY STANDARD FOR ELECTRICAL

INSTALLATIONS AND CAN/ULC-S540

INSTALLATION OF RESIDENTIAL FIRE

WARNING SYSTEMS.

THE LYNXR-I CONTROL IS COMPATIBLE WITH

THE FOLLOWING INTEGRAL RECHARGEABLE

BATTERY PACKS:

EXTERNAL SOUNDERS

AND POWERLINE

CARRIER DEVICES HAVE

NOT BEEN EVALUATED

BY UL.

FUTURE USE

GND

REPLACE EVERY FOUR YEARS

P/N LYNXRCHKIT-SC

P/N LYNXRCHKIT-HC

P/N LYNXRCHKIT-SHA

*WHEN AVAILABLE

1 2 3 4

BLACK

RED

YELLOW

GREEN

PL513

POWERLINE

INTERFACE

(IF USING

X10 DEVICES)

4-WIRE MODULAR PHONE

CORD WITH FLYING LEADS

K10145CN

PLUG-IN

TRANSFORMER

9VAC, 25VA

915 16

13 14

FOR CANADIAN INSTALLATIONS

RING

TIP

RING

TIP ( ) ( ) (+)

(+)

( ) DATA

OUT

SYNC

POWERLINE

CARRIER DEVICES

GND

D ATA I N

DATA OUT

INCOMING

PHONE

LINE

HANDSET

PHONE

LINE

WARNING:

TO PREVENT RISK OF

SHOCK DISCONNECT

TELEPHONE LINE

AT TELECOM JACK

BEFORE SERVICING

THIS UNIT.

ALL OUTPUT CIRCUITS ARE POWER LIMITED.

123486

511

710 12 15 16

13 14

PHONE

FUTURE

USE SOUNDERS PLCD AC

EARTH

GROUND

RING

TIP

RING

TIP ( ) ( ) (+)

(+)( ) DATA

OUT

SYNC

RJ11

POS

JACK

GND

LOCAL SOUNDER

DISABLE SHUNT

REMOVE TO DISABLE

UL NOTE

THE MINIMUM WIRE SIZE USED FOR TELEPHONE

INSTALLATIONS MUST BE #26 GAUGE

SUPER HIGH-CAPACITY

BATTERY CONNECTOR

LRR/IP

COMMUNICATIONS

PORT

GSML/GSMVL

COMMUNICATIONS

PORT

STANDARD

HIGH-CAPACITY

BATTERY CONNECTOR

UL INSTALLATIONS

THE MINIMUM WIRE

SIZE USED FOR

TELEPHONE

INSTALLATIONS

MUST BE #26 GAUGE

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14945TŠ

K14945 1/08 Rev. A

Inhaltsverzeichnis

Andere Honeywell Sicherheitssystem Handbücher

Honeywell

Honeywell Galaxy Keyprox Technische Daten

Honeywell

Honeywell ADEMCO VISTA-48A Montageanleitung

Honeywell

Honeywell GENT Nano panel-based Schulungshandbuch

Honeywell

Honeywell Optiflex Interactive Bedienungsanleitung

Honeywell

Honeywell Lynx Plus Series Montageanleitung

Honeywell

Honeywell 5800WAVE - Ademco Wireless Siren Montageanleitung

Honeywell

Honeywell FG8MS Bedienungsanleitung

Honeywell

Honeywell First Alert FA130CP Bedienungsanleitung

Honeywell

Honeywell SEF8MS Bedienungsanleitung

Honeywell

Honeywell VISTA-128BP Montageanleitung

Honeywell

Honeywell ADEMCO 4110XM Bedienungsanleitung

Honeywell

Honeywell Frieland FGGA06 Series Bedienungsanleitung

Honeywell

Honeywell PID-95P Leitfaden

Honeywell

Honeywell LYNX TOUCH L5200 Bedienungsanleitung

Honeywell

Honeywell VISTA-128BPT Montageanleitung

Honeywell

Honeywell Gamewell-FCI E3 Series Bedienungsanleitung

Honeywell

Honeywell Ademco Vista-12D Montageanleitung

Honeywell

Honeywell 013002 Bedienungsanleitung

Honeywell

Honeywell HS-6270 Bedienungsanleitung

Honeywell

Honeywell ADEMCO LYNXR-ENSIA Bedienungsanleitung

Honeywell

Honeywell First Alert 145C Bedienungsanleitung

Honeywell

Honeywell INTELLIGUARD 9000 Bedienungsanleitung

Honeywell

Honeywell L5200 Series Bedienungsanleitung

Honeywell

Honeywell VISTA-20PSeries Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung